- SCM PC
Transcription
- SCM PC
Deutsch IDE CF Carddrive 3,5’’ 775-0051-05 Produktbeschreibung Das IDE CF Carddrive 3,5’’ RoHS ist ein Kartenkaufwerk, welches an die IDESchnittstelle angeschlossen wird. Das Laufwerk unterstützt CompactFlash Karten Typ I und Typ II sowie Microdrive. Das IDE CF Carddrive konvertiert automatisch den 50 Pin ATA-Modus der CompactFlash-Karte auf einen 40-poligen IDE-Anschluss. Im Bios erscheint das Laufwerk bei gesteckter CompactFlash Karte direkt als IDE-Laufwerke. Das IDE CF Carddrive 3,5’’ RoHS hat die gleiche Größe wie eine 3,5’’ Diskettenlaufwerk und kann ohne viel Aufwand frontseitig in den Computer eingebaut werden, wodurch man einen einfachen Zugriff auf das Laufwerk hat. Installation 1. Schalten Sie den Computer aus. 2. Entfernen Sie das Gehäuse von Ihrem Computer. 3. Entfernen Sie die Frontplatte des für das Laufwerk vorgesehenen 3,5’’ Schachtes. 4. Schieben Sie das IDE CF Carddrive 3.5’’ RoHS in den freien 3,5’’ Schacht und befestigen sie es dann mit den beiliegenden Schrauben. 5. Schließen Sie ein 40-poligen IDE-Kabel an das IDE CF Carddrive an und verbinden Sie dieses dann mit dem Mainboard des Rechners. Die rote Ader des IDE-Kabels muss dabei sowohl auf dem Mainboard wie auch am Carddrive an Pin 1 (eins) angeschlossen werden. 6. Verbinden Sie ein Netzkabel von Ihrem Computer Netzteil mit dem Netzanschluss des IDE-Laufwerkes. Aufgrund der Form des Netzsteckers ist es nicht möglich, diesen falsch anzuschließen. 7. Schließen Sie das Gehäuse des Computers. 8. Die Installation eines Treibers ist nicht erforderlich. Hinweis 1. Das IDE-Laufwerk unterstützt keine CF-Adapter und I/O Karten. Diese Karten sind nicht kompatibel mit dem ATA & ATAPI Protokoll. 2. Das IDE CF Carddrive 3.5’’ RoHS unterstützt kein Hot-Swap. Schalten Sie den Rechner aus, bevor Sie eine CompactFlash-Karte einstecken oder entfernen. English Introduction The IDE CF Carddrive 3.5’’ RoHS is an IDE interface card drive in one inch height. Just connect IDE drive to a personal computer with an IDE controller, the card drive then support Compact Flash Type I & Type II (Micro Drive). The card drive automatically sets the 50 pins ATA mode of CompactFlash Card connect a 40-pin IDE connector allowing the system Bios to access the card directly as an IDE drives. The IDE CF Carddrive 3.5’’ RoHS is the same size as a 3.5’’ floppy disk drive so it can be mounted on the front of a Computer's case. This gives you convenient access to the drive, installation is easy - simply mount the drive in a free 3.5" drive mount on the front of the computer, connect he IDE cable and then connect the standard power cable from your computer's power supply to the power connector at the rear of the drive. Installation steps: 1. Turn off your computer. 2. Remove the case from your computer. 3. Remove the protect faceplate that covers a free 3.5’’ disk drive bay in your computer. 4. Insert the IDE CF Carddrive 3.5’’ RoHS in to the computer's 3.5’’ disk drive bay and secure the drive by affixing fours screws to the bay's rails. 5. Connect a specific 40-pin IDE cable from the ATA to IDE drive's IDE connector and then to the IDE connector on the mainboard. Make sure that the cable's red edge is connected to pin 1 on each of the connectors. 6. Connect a power cable from your computer's power supply to the power connector on the ATA to IDE drive. Owing to the shape of the cable and connector, it is impossible to plug in this cable incorrectly. 7. Replace the case on your computer. 8. A driver installation is not required. Notice: 1. 2. IDE drives didn't support CF adapter & I/O card, due to these cards does not comply with ATA & ATAPI Command. The IDE CF Carddrive 3.5’’ RoHS does not support Hot-Swap. Shutdown your PC before inserting or removing a CF card.