Mini WhiteSON and White SON High Pressure Sodium Lamps
Transcription
Mini WhiteSON and White SON High Pressure Sodium Lamps
Mini WhiteSON and White SON High Pressure Sodium Lamps Warnings, Cautions and Operating Instructions WARNING: These lamps must be operated in fixtures designed for use with High Pressure Sodium lamps. The fixture wattage rating must match the wattage indicated on the outer glass bulb. Do not scratch the outer bulb or subject it to pressure as this could cause the outer bulb to crack or shatter. A partial vacuum in the outer bulb may cause glass to fly if the glass is struck. Operating the lamp improperly may result in PERSONAL INJURY, PROPERTY DAMAGE, BURNS AND FIRE. 1. If the outer glass bulb is broken, shut off power immediately and remove the lamp after it has cooled. 2. Use only auxiliary equipment meeting Philips and/or ANSI standards. Use within voltage limits recommended by ballast manufacturer. A. Operate lamp only within specified limits of operation. B. For total supply load refer to ballast manufacturers electrical data. C. Operate Mini WhiteSON lamps only on approved electronic ballasts. 3. Protect lamp base, socket and wiring against moisture, corrosive atmospheres and excessive heat. 4. Replace the lamp if the outer glass bulb has been scratched, cracked or damaged in any way. 5. If a lamp bulb support is used, be sure to insulate the support electrically so as to avoid possible decomposition of the bulb glass. 6. Do not use this lamp in a fixture which redirects a substantial portion of the energy toward the arc tube and its immediate vicinity, as this may lead to very early lamp failure. 7. Take care in handling and disposing of lamps. If arc tube is broken, avoid skin contact with any of the contents or fragments. 8. The arc tube of this lamp contains sodium and mercury. Dispose of in accordance with federal, state and local requirements. 9. It is possible that the light color will suddenly change. After some time the lamp will regain its old color. 10. In order to prevent damage to the ballast, the lamp should be replaced as quickly as possible at the end of its lifetime (lamp color turns yellow, lamp flickers and fails to start). 11. For Mini WhiteSON lamps, after 10,000 hours of burning the light color will become yellow. The lamp must then be replaced. 12. For WhiteSON lamps, after 7,500 hours of burning the light color will become yellow. The lamp must then be replaced. MASTER SDW-T MASTER SDW-T 100W/825 PG12-1 1SL Lampe Sodium blanc Données du produit • Caractéristiques Générales Description système Culot Forme de la lampe Matériaux ampoule Finition ampoule Position fonctionnement Durée de vie 5% de mortalité Durée de vie 20% de mortalité Durée de vie utile Durée de vie 50% de mortalité Tension réseau [200-250V] PG12-1 T31 [T 31mm] Verre dur Clair toutes [Universelle] 5000 hr 10000 hr 10000 hr 15000 hr 530 cd/cm2 • Caractéristiques électriques Puissance lampe Puissance lampe EM Tension de la lampe Courant lampe EM Gradable 100 W 97.0 W 98 V 1.31 A Non • Caractéristiques environnementales Contient du mercure 11 mg • Exigences conception du luminaire • Caractéritiques techn. de lumière Code couleur Indice de rendu des couleurs Désignation teinte Température de couleur Température de couleur techn. Coordonnée chromatique X Coordonnée chromatique Y Flux lumineux EM Eff. lum. lampe sur ballast EM Maintien du flux à 2000 h Maintien du flux à 5000 h Luminance sur ballast EM 825 [CCT of 2500K] 80 (min), 83 (nom) Ra8 Blanc doré 2500 K 2500 K 464 404 5000 Lm 52 Lm/W 85 % 80 % Température culot Température ampoule 120 (max) C 450 (max) C • Dimensions en mm. Longeur totale C Diamètre ampoule D Hauteur du centre lumineux L Longeur arc O 149 (max) mm 32 (max) mm 91 mm 19 mm • Données produit Code commercial Code produit EOC Nom produit Désignation 734044 15 871150073404415 MASTER SDW-T 100W/825 PG12-1 1SL MASTER SDW-T 100W/825 PG12-1 1SL/12 MASTER SDW-T Pièces par pack Config. Emballage Packs par carton Code barre produit Code barre carton regroup. 1 12 12 8711500734044 8711500831163 Code usine Code ILCOS Poids net unitaire 928154109227 STH-100-H/E-PG12 0.055 kg Mises en garde et sécurité • S'utilise exclusivement avec un ballast philips dédié. Schéma dimensionnel SDW-T, PG12-1 D Product C (Max) D (Max) L (Norm) O (Norm) 32 91 18.3 L C O SDW-T 100W/825 PG12-1 149 12 PG12-1 Données photométriques [ W / (5nm. lm)] 300 250 200 150 100 50 300 400 500 600 700 [nm] MASTER SDW-T 2012, janvier 12 Les données sont sujettes à changement MASTER SDW-T © 2012 Koninklijke Philips Electronics N.V. Tous droits réservés. Les données sont sujettes à changement sans préavis. Les noms et marques sont la propriété de Koninklijke Philips Electronics N.V. ou de leurs ayants droits respectifs. www.philips.com/lighting 2012, janvier 12 Les données sont sujettes à changement