Montageanleitung HALFEN Fertigteilanschluss HVL
Transcription
Montageanleitung HALFEN Fertigteilanschluss HVL
Montageanleitung Instructions HALFEN Fertigteilanschluss HALFEN precast connection HVL - 03/09 Seite Page 1/2 Montage- und Einbauteile Assembly and installation components Montageteil HVL-M, vormontiert bestehend aus: ▪ Hammerkopflasche mit Zahnung, ▪ 1 gezahnte Gegenplatte, ▪ 2 Schraubenbefestigungssätze (Halfenschraube HS 38/17 - M 12 x 50 + U-Scheibe + Kegeldruckfeder) 1 Einbauteil HVL-E = Halfenschiene HTA 38/17 - 300 - UB im anzuschließenden Betonfertigteil Halfenschiene HTA 38/17 senkrecht einbetoniert in Betonpfeiler 1 Tie assembly HVL-M, pre-assembled consists of: ▪ hammer head strap with serration, ▪ 1 toothed counter plate, ▪ 2 bolt fixing sets (HALFEN bolt HS 38/17 - M 12 x 50 + washer + tapered compression spring) 2 3 Insert HVL-E = HALFEN cast-in HTA 38/17 - 300 - UB in the precast concrete element to be connected HALFEN cast-in channel HTA 38/17 vertically installed in concrete column Auf die richtige Lage der Rastungsplatte achten! The appropriate position of the toothed counter plate must be observed! Betonfertigteil Precast concrete element Die Zahnungen müssen ineinander greifen! Teeths of serrations must interlock! Montageanleitung Instructions Montage HALFEN Fertigteilanschluss HALFEN precast connection HVL - 03/09 Seite Page 2/2 Assembly Montage: 1. Anzuschließendes Betonfertigteil grob ausrichten. 2. Lasche mit Hammerkopf in die Halfenschiene im Pfeiler und mit beiden vormontierten Halfenschrauben in das Einbauteil HVL-E im Anschlussbauteil einsetzen. 3. Schrauben eindrücken, um 90° im Uhrzeigersinn drehen und wieder loslassen. 4. Lage des anzuschließenden Betonfertigteil genau ausrichten. Für seitliche Justierung Rastungsplatte anheben. 5. Auf richtigen Sitz der Rastungsplatte achten, ggfs. richtigstellen. 6. Muttern auf den Schrauben mit dem erforderlichen Anzugsdrehmoment von 25 Nm festziehen. 7. Mörtelverguss im Endzustand. 3 Betonfertigteil Precast concrete element 25 Nm 1 25 Nm 2 U - 159 - 03/09 Assembly: 1. Align the connecting precast element approximately. 2. Insert the tie with the T-head into the HTA Channel in the column and with the 2 pre-assambled HALFEN bolts in the HVL-E insert in the connecting pre-cast element. 3. Press the Halfen bolts into the channel slot of the HVL-E insert, turn clockwise by 90° and unhand them. 4. Align the connecting precast-element precisely. For lateral adjustment raise the serrated counter plate. 5. Check the correct seating of the serrated counter plate and adjust if necessary. 6. Tighten the nuts on the HALFEN bolts to the required torque of 25 Nm. 7. Fill the remaining recess with mortar as final step. Betonpfeiler Concrete column Halfen GmbH Das Qualitätsmanagementsystem von Halfen GmbH ist für die Standorte in Deutschland, in der Schweiz und in Polen zertifiziert nach DIN EN ISO 9001:2000, Zertifikat-Nr. QS-281 HH. The Quality Management System of Halfen GmbH is certified for the locations in Germany, Switzerland and Poland according to %*/&/*40, Certificate No. QS-281 HH. 567 Liebigstr. 14 ⋅ 40764 Langenfeld ⋅ GERMANY +49 - (0)2173 / 970-9020 +49 - (0)2173 / 970-450 E-Mail: [email protected] www.halfen.com