MAZDA Miata - Directechs.com
Transcription
MAZDA Miata Back view 3 4 5 6 7 8 9 10 11 12 N.c. Blue* White* conn. Black* Red* Blue* White* Black* Red* Orange/Green Brown Ignition Data 1.B Connector 2 (White): Make the connections 1.C Connector 3 (White): Make the connections 3 1 3 +12V Ground Rev. 20100119 1 Press and hold the programming button. Insert connector 1. Insert connector 2. If the LED is flashing at this point the module is already programmed and can’t be programmed again. (To prevent malicious use this module can be programmed in only one vehicle.) 4 D2D connector WWW.XPRESSKIT.COM Connector 1 (White): Determin the type of installation: - INSTALLATION WITH D2D - INSTALLATION WITHOUT D2D 2 Red/Black CAUTION: Be careful NOT to plug connector into the Black port Connector 1 (White - 4 pins): which also accepts a 4-pin Determine the type of installation: connector. Relay 1a Light Green Relay 1b Orange/Brown PKALL Make the connections to the vehicle: 1.A N.c. Black/White Front view of the module 1 While holding the programming button. 3 Programming button CUT 2 INSTALLATION WITHOUT D2D 1 2 Immobilizer module Located near steering column Data Purple/White Yellow/Black N.c. Blue/White (-) While running Green N.c. Ignition Pink Black N.c. INSTALLATION WITH D2D 2001-2004 2 LED Module Diagnostics : On: Activated. OFF: Not activated. Flash: Not programmed. U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product. Insert connector 3. 5 Release the programming button when the LED turns ON. Press 1 time on the programming button. The LED turns OFF and turns ON. 6 Cut off one plug of the D2D connector, connect the blue wire to +12V and the black wire to ground. *Wire colors may vary on the kit you have purchased. Press 5 more times on the programming button and the LED will flash 4 times. 7 OFF conn. Connector 4 (White - 4 pins): Connect with the XK Loader for web update. IGN 8 4 START XK Loader Connector conn. Turn the ignition key to the START position. If the LED flashes 10 times, the module is programmed. If the LED stays ON, verify your connections and repeat from step 1. 9 OFF Back view of the module Connect wire to Remote-Starter/Alarm Connect wire to vehicle TECHNICAL SUPPORT INFORMATION OUTPUT INPUT 10 IGN Turn the Ignition key to the OFF position. START web resources: www.xpresskit.com www.xpressvip.com www.directechs.com 11 Remove the key and start the vehicle using the remote starter to ensure functionality. MAZDA Miata Vue de dos 3 4 5 6 7 8 9 10 11 12 Noir/Blanc Rouge/Noir ATTENTION : S'assurer de ne pas brancher le connecteur dans le Connecteur 1 (White - 4 pins): port noir qui peut aussi accepter Déterminez le type d’installation: un connecteur 4-broches. Data Bleu* Blanc* conn. Noir* Rouge* Bleu* Blanc* Noir* Rouge* 1.B Connecteur 2 (Blanc): Effectuez les branchements. 1.C Connecteur 3 (Blanc): Effectuez les branchements. Brun N.c. Ignition Vue de face du module Orange/Vert 2 3 1 1 Connecteur D2D +12V conn. Rev. 20100119 Maintenez le bouton de programmation enfoncé. Insérez le connecteur 1. Insérez le connecteur 2. Si la DEL clignote alors le module a déjà été programmé sur un véhicule et ne peut être programmé à nouveau. (Dans le but de prévenir toute utilisation malicieuse, ce module peut être programmé dans seulement (1) un véhicule.) 4 3 WWW.XPRESSKIT.COM Connecteur 1 (Blanc): Déterminez le type d’installation: - Pour l’INSTALLATION D2D - Pour l'INSTALLATION NON D2D Relais 1a Vert Pâle Relais 1b Orange/Brun N.c. Mauve/Blanc Data Jaune/Noir N.c. Bleu/Blanc (-) While running Vert N.c. Pink Ignition Noir N.c. PKALL Effectuez les connexions au véhicule: 1 CUT Programming button 1 1.A 2 INSTALLATION SANS D2D 1 2 Gardez le bouton de programmation enfoncé et 3 Module d'immolisation localisé près de la colonne de direction INSTALLATION AVEC D2D 2001-2004 2 Diagnostique du DEL du module Allumé: Le module est activé. Éteint: Le module n'est pas activé. Flash: Le module n'est pas programmé. U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product. insérez le connecteur 3. Lorsque la DEL s’allume, relâchez le bouton de programmation. 5 Masse Appuyez 1 fois sur le bouton de programmation. La DEL s'éteint et se rallume. 6 Coupez les 4 fils à l’extrémité de l’un des deux connecteurs D2D. Connectez le fil bleu au 12V et le fil noir à la masse du véhicule. *Les couleur des fils peut varier selon le kit acheté. Appuyez 5 autres fois sur le bouton de programmation et la DEL clignotera quatre coups. 7 Connecteur 4 (Blanc - 4 pins): Connectez avec le XK Loader pour les mises à jour par internet. 4 OFF conn. 8 IGN Connecteur XK Loader conn. La DEL clignote 10 fois le MODULE est programmé. Vue de dos du module 9 Branchement du filage au véhicule TECHNICAL SUPPORT INFORMATION Si la DEL reste allumée, vérifiez vos connexions et recommencez la programmation à partir de l'étape 1. OFF Branchement du filage au démarreur à distance/Alarme Tournez la clef en position START. START SORTIE ENTRÉE 10 IGN START Tournez la clef à OFF. web resources: www.xpresskit.com www.xpressvip.com www.directechs.com 11 Retirez la clé du barillet et démarrez le véhicule avec le démarreur à distance.
Documents pareils
HYUNDAI Tucson V6 2005-2007
U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product.
Plus en détailHONDA Prelude - Directechs.com
If the LED is flashing at this point the module is already programmed and can’t be programmed
Plus en détailHYUNDAI XG350 - Directechs.com
U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product.
Plus en détailLEXUS RX330 2004-2006
Insert one functional key into the ignition barrel. (do not turn the key).
Plus en détailHyundai Tiburon V6 2002-2008
U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product.
Plus en détail