HONDA Prelude - Directechs.com
Transcription
HONDA Prelude 1997 1 Immobilizer module Located at the base of the steering column Data Ground Out 2 Start Enable Light Blue conn. N.c. N.c. 1 conn. NOTE : REQUIRED ON SOME VEHICLES. Make this connection if the car does not start when remote started. Brown/Yellow Start Enable Ignition Black/Yellow Programming button Purple/White Yellow/Black Blue/White Green Pink Black 2 3 7 8 5 6 See bottom of the page 1.B Connector 2 (White): Make the connections 1.C Connector 3 (White): Make the connections 2 Press and hold the programming button. Insert connector 1. 1 1 4 B A Insert connector 2. Data 3 If the LED is flashing at this point the module is already programmed and can’t be programmed again. (To prevent malicious use this module can be programmed in only one vehicle.) Ignition conn. 3 4 Relay 1a Relay 1b While holding the programming button. 3 Light Green Orange/Brown Orange/Green Brown Rev.20100119 Connector 1 (White): Determin the type of installation: - INSTALLATION WITH D2D - INSTALLATION WITHOUT D2D 1.A CONNECTOR A PKALL WWW.XPRESSKIT.COM Make the connections to the vehicle: 2 LED Module Diagnostics : On: Activated. OFF: Not activated. Flash: Not programmed. U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product. Insert connector 3. N.c. N.c. 5 Release the programming button when the LED turns ON. conn. Connector 4 (White - 4 pins): Connect with the XK-Loader for web update. Back view of the module Connector 1 (White- 4 pins): Détermine the type of installation: Blue* INSTALLATION WITH D2D White* Black* Red* conn.INSTALLATION 1 7 CAUTION: Be careful NOT to plug connector into the Black port which also accepts a 4-pin connector. WITHOUT D2D Blue* Press 1 more time on the programming button and the LED will flash once. OFF 4 XK Loader Press 1 time on the programming button. The LED turns OFF and turns ON. 6 IGN 8 +12V Turn the Ignition to the ON position. START White* Black* Ground If the LED flashes 10 times, the module is programmed. If the LED stays ON, verify your connections and repeat from step 1. Red* 9 OFF Cut off one plug of the D2D connector, connect the blue wire to +12V and the black wire to ground *Wire colors may vary on the kit purchased. Connect wire to Remote-Starter/Alarm Connect wire to vehicle TECHNICAL SUPPORT INFORMATION OUTPUT INPUT 10 IGN START Turn the Ignition key to the OFF position. web resources: www.xpresskit.com www.xpressvip.com www.directechs.com 11 Remove the key and start the vehicle using the remote starter to ensure functionality. Make Model HONDA Prelude Year(s) 1997 KEY-OVERRIDE-ALL V.3.03 & + 1 Module d'immolisation situé à la base de la colonne de direction CONNECTEUR A 2 Bleu pâle conn. N.c. Data Ground Out Start Enable Ignition N.c. Noir/Jaune 1 conn. Voir le bas de la page. Vue de face du module Start Enable NOTE : REQUIS SUR CERTAINS VÉHICULES SEULEMENT. Branchez si le véhicule ne démarre pas au démarrage à distance. Brun/Jaune Programming button Mauve/Blanc Jaune/Noir Bleu/Blanc Vert Pink Noir 2 3 7 8 5 6 1.B Connecteur 2 (Blanc): Effectuez les branchements. 1.C Connecteur 3 (Blanc): Effectuez les branchements. 2 Maintenez le bouton de programmation enfoncé. Insérez le connecteur 1. Insérez le connecteur 2. Si la DEL clignote alors le module a déjà été programmé sur un véhicule et ne peut être programmé à nouveau. (Dans le but de prévenir toute utilisation malicieuse, ce module peut être programmé dans seulement (1) un véhicule.) Data 3 Ignition conn. Relais 1a Relais 1b 3 4 N.c. Gardez le bouton de programmation enfoncé et 3 Vert Pâle Orange/Brun Orange/Vert Brun insérez le connecteur 3. N.c. Lorsque la DEL s’allume, relâchez le bouton de programmation. 5 4 Connecteur 4 (Blanc - 4 pins): Connectez avec le XK-Loader pour les mises à jour par internet. Connecteur XK Loader Vue de dos du module Rev.20100119 Connecteur 1 (Blanc): Déterminez le type d’installation: - Pour l’INSTALLATION D2D - Pour l'INSTALLATION NON D2D 1.A 11 1 4 B A PKALL WWW.XPRESSKIT.COM Effectuez les connexions au véhicule: 2 Diagnostique du DEL du module Allumé: Le module est activé. Éteint: Le module n'est pas activé. Flash: Le module n'est pas programmé. U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product. Appuyez 1 autre fois sur le bouton de programmation et la DEL clignotera un coup. 7 ATTENTION : S'assurer de ne pas brancher le connecteur dans le port noir qui peut aussi accepter un connecteur 4-broches. OFF Connecteur 1 (Blanc - 4 pins): Déterminez le type d’installation: Appuyez 1 fois sur le bouton de programmation. La DEL s'éteint et se rallume. 6 conn. INSTALLATION ÀVEC D2D Bleu* Blanc* Noir* 1 Bleu* Blanc* Noir* 8 +12V IGN Tournez la clef en position START. START Masse Rouge* Coupez les 4 fils à l’extrémité de l’un des deux connecteurs D2D. Connectez le fil bleu au 12V et le fil noir à la masse du véhicule. *Les couleur des fils peut varier selon le kit acheté. La DEL clignote 10 fois le MODULE est programmé. 9 Si la DEL reste allumée, vérifiez vos connexions et recommencez la programmation à partir de l'étape 1. OFF Rouge* INSTALLATION SANS D2D Branchement du filage au démarreur à distance/Alarme Branchement du filage au véhicule TECHNICAL SUPPORT INFORMATION SORTIE ENTRÉE 10 IGN START Tournez la clef à OFF. web resources: www.xpresskit.com www.xpressvip.com www.directechs.com 11 Retirez la clé du barillet et démarrez le véhicule avec le démarreur à distance.
Documents pareils
Honda CRV 2007-2010
If the LED is flashing at this point the module is already programmed and can’t be programmed again. (To prevent malicious use this module can be programmed in only one vehicle.)
Plus en détailHYUNDAI Tucson V6 2005-2007
U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product.
Plus en détailHYUNDAI XG350 - Directechs.com
U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product.
Plus en détailHyundai Tiburon V6 2002-2008
U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product.
Plus en détailLEXUS RX330 2004-2006
Insert one functional key into the ignition barrel. (do not turn the key).
Plus en détail