Nissan XTerra - Directechs.com
Transcription
Nissan XTerra - Directechs.com
Nissan XTerra NOT INTELLIGENT-KEY R Tach £ Start Enable R Door Trigger R Trunk Trigger R Hood Trigger £ Radio Off R Transponder Bypass £ PK3, Passlock £ Sliding Door £ Defrost £ Heat Seats £ Gas Door £ Window Roll Open £ Hatch £ Brake Signal Orange 8 8 1 Programming button 14 White/Red Violet/White Tach conn. (-) While Running (status) Blue/White 2 N.C. Lock White/Black Grey ~ Violet/Black Light Green Blue Ignition Pink Hood Trigger Red/White 14 * Only if the vehicle is equipped with a hood trigger. 1 Back of the module 3 Brown Orange/Green Orange/Brown Light Green Yellow White/Black Grey Violet/White Blue/White Green Brown violet/Black Orange/Green Orange/Brown Blue Light Green Red/White White/Violet Lt. Green Pink 14 20 19 18 17 16 15 14 13 12 11 10 9 8 Make the connections of the DLPK to the vehicle: N.C. 1.A Unlock Trunk 1.B Connector 2 (White): Make the connections 1.C UNLOCK Connector 3 (White, located at the back of the module): Make the connections LOCK 7 6 5 4 3 1 Press the programming switch while inserting the main wires harness (CONN 1) into the DLPK module. The LED will illuminate to indicate you are in programming mode, release the programming button. 2 1 3 Connect the other connectors (CONN. 2). WARNING: Connector 2 can be easily plugged in backwards. N.C. (CAN High) Data (CAN Low) Data N.C. 4 Connect the other connectors (CONN. 3). OR Pin 6 N.C. (CAN High) Data (CAN Low) Data IGN 5 6 Turn the key to the "ON" position. START 14 N.C. Pin14 Once the LED starts to flash rapidly turn the key to the OFF position. Connect wire to vehicle TECHNICAL SUPPORT INFORMATION OUTPUT INPUT web resources: www.xpresskit.com www.xpressvip.com www.directechs.com 6 The LED will turn off to indicate the module has been programmed. OFF Connect wire to Remote-Starter/Alarm 4 Connector 1 (Black): Determine the type of installation: INSTALLATION WITH D2D INSTALLATION WITHOUT D2D 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 4 1 7 OFF 4 Brown Orange/Green Orange/Brown Light Green 4 2 Programming button 1 Brown Orange/Green Orange/Brown Light Green 1 2 Front view of the BCM connector located on the driver kick panel or above the acceleration pedal. 1 White/Red 1 7 7 For vehicles equipped with OEM alarm, connect the following wires to the empty pins on the BCM to control door-locks and OEM-alarm.. Front of the module 8 N.C. Green Door + Trunk Trigger White/Violet Orange violet/Black Blue Red/White D2D (2 way) Connect: Yellow Green White/Violet Lt. Green Pink Yellow Rev.: 20091112 White/Black Grey Violet/White Blue/White Vehicle security light Orange Driver Door Trigger 1 White/Red LED DLPK WWW.XPRESSKIT.COM D2D (1 way) Connect: 3 Functional if equipped R Lock R Unlock £ Arm £ Disarm R Trunk 2005 U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product. IGN The module is now ready for use. START Nissan XTerra Programming button NOT INTELLIGENT-KEY 2005 U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product. DLPK WWW.XPRESSKIT.COM Rev.: 20091112 Connector 1 (Black - 4 pins): Determine the type of installation: INSTALLATION WITH D2D 1 1 D2D Cable INSTALLATION WITHOUT D2D Blue* Black* 1 +12V Ground Cut off one plug of the D2D connector, connect the blue* wire to +12V and the black* wire to ground. *Wire colors may vary on the kit you have purchased. Front of the module Connect wire to Remote-Starter/Alarm Connect wire to vehicle OUTPUT TECHNICAL SUPPORT INFORMATION INPUT web resources: www.xpresskit.com www.xpressvip.com www.directechs.com Nissan XTerra NOT INTELLIGENT-KEY Sièges Chauffants £ £ Porte Essence £ Contrôle Portes £ Hayon Arrière £ Signal de Frein Orange conn. (-) Masse d’activation (status) Bleu/Blanc 2 1 Blanc/Rouge Violet/Blanc Tach 8 Blanc/Noir Violet/Noir Vert pâle Programming button Vue de face de la prise du BCM située dans le panneau latéral côté conducteur ou au-dessus de la pédale d’accélération. 1 4 1 Vue de dos du module Brun Orange/Vert Orange/Brun Vert Pâle 3 Brun Orange/Vert Orange/Brun Vert Pâle Jaune Blanc/Noir Gris Violet/Blanc Bleu/Blanc Vert Brun Orange/Vert Violet/Noir Orange/Brun Bleu Vert pâle Rouge/Blanc Blanc/Violet Vert pâle Rose 14 1 4 7 Effectuez les connexions du DLPK au véhicule: 1 Connecteur 1 (Noir): Déterminez le type d’installation (D2D ou non D2D) Pour l’installation D2D assurez vous de la présence du connecteur D2D sur le démarreur. Pour installation non D2D voir INSTALLATION SANS D2D. 1.A Valise 1.B Connecteur 2 (Blanc): Éffectuez les branchements 1.C DÉVERROUILLAGE Connecteur 3 (Blanc, situé au dos du module): Éffectuez les branchements VERROUILLAGE 2 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 Maintenez le bouton de programmation enfoncé en insérant le connecteur 1 dans le DLPK. Le DEL s'allume pour indiquer le début de la programmation, relâchez le bouton de programmation. 2 1 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 3 Branchez le connecteur 2 (CONN. 2). ATTENTION: Ne pas brancher le connecteur à l’envers. N.C. (CAN High) Data (CAN Low) Data N.C. 4 Branchez le connecteur 3 (CONN. 3). OU Pin 6 N.C. (CAN High) Data (CAN Low) Data N.C. 11 IGN 5 6 Tournez la clef en position ignition. START 14 Pin14 4 Branchement du filage au démarreur à distance/Alarme 1 4 7 7 Pour les véhicules avec l'alarme d'origine, ajoutez des fils dans les espaces vides du BCM pour contrôler les portes électriques et l'alarme d'origine du véhicule. Vue de face du module N.C. Rouge/Blanc 14 Brun Orange/Vert Orange/Brun Vert pâle Déverrouillage Bleu Rose Ignition * Seulement si le véhicule est équipé du contact pour le capot. Vert Contact Porte + Valise Blanc/Violet N.C. Verrouillage 1 N.C. Contact Capot Gris ~ Violet/Noir Bleu Rouge/Blanc 14 8 Blanc/Rouge Vert Blanc/Violet Vert pâle Rose Jaune Orange Blanc/Noir Gris Violet/Blanc Bleu/Blanc D2D (2 way) Brancher: Jaune 1 Contact Porte Chauffeur 1 3 Programming button Orange 8 Blanc/Rouge Lumière de sécurité du véhicule Rev.: 20091112 D2D (1 way) Branchez: DEL DLPK WWW.XPRESSKIT.COM OFF Radio Off £ R Transponder Bypass £ PK3, Passlock £ Portes Coulissantes £ Dégivrage Branchement du filage au véhicule TECHNICAL SUPPORT INFORMATION SORTIE ENTRÉE web resources: www.xpresskit.com www.xpressvip.com www.directechs.com 6 Lorsque le DEL clignote rapidement, tournez la clef en position OFF. OFF Tach R £ Active Démarreur R Status de Porte R Status de Valise R Status de Capot 2 Fonctionnel si équipé Verrouillage R R Déverrouillage £ Armement £ Désarmement R Valise 2005 U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product. IGN START Le DEL s'éteint pour indiquer que le module est programmé. Nissan XTerra Programming button NOT INTELLIGENT-KEY 2005 U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product. DLPK WWW.XPRESSKIT.COM Rev.: 20091112 Connecteur 1 (Noir - 4 pins): Determinez le type d’installation : 1 INSTALLATION AVEC D2D 1 D2D Cable INSTALLATION SANS D2D Bleu* Noir* 1 +12V Masse Coupez les 4 fils à l’extrémité de l’un des deux connecteurs D2D. Connectez le fil bleu* au 12V et le fil noir* à la masse du véhicule. *La couleur des fils peut varier selon le kit. Vue de face du module Branchement du filage au démarreur à distance/Alarme Branchement du filage au véhicule SORTIE TECHNICAL SUPPORT INFORMATION ENTRÉE web resources: www.xpresskit.com www.xpressvip.com www.directechs.com
Documents pareils
NISSAN Maxima - Directechs.com
violet/Black Orange/Green Orange/Brown Blue Light Green Red/White
Plus en détailPontiac G6 - Directechs.com
U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product.
Plus en détailPontiac G5 Pursuit 2007-2009
Press the programming switch while inserting the main wires harness (CONN 1) into the DLPK module. The LED will illuminate to indicate you are in programming mode, release the programming button.
Plus en détailPontiac Solstice
Press the programming switch while inserting the main wires harness (CONN 1) into the DLPK module. The LED will illuminate to indicate you are in programming mode, release the programming button.
Plus en détail