2003-2007 HONDA Accord
Transcription
2003-2007 HONDA Accord
HONDA Accord Programming Button N.C. Trunk Trigger Tach conn. Orange White/Red Violet/White (-) While Running (status) 1 8 1 ~ Blue/White 2 Defrost Lock Ignition Heat Seats Gas Door Window Roll Down Hatch Brake Signal White/Violet Light Green Pink Connect: Yellow White/Black Gray Green Violet/Black Orange White/Red Violet/White Blue/White White/Violet Lt. Green Pink N.C. 1 Unlock Trunk 7 Connector 1 (Black - 4 pins): Determine the type of installation: 1 Blue* Black* 1 N.C. 3 Connect the other connectors (CONN. 2) Connect the other connectors (CONN. 3) 21 20 19 18 17 16 15 14 13 12 11 10 3 8 7 6 5 4 3 2 1 IGN 5 START Turn the key to the "ON" position. Brown/Red Back of the module Once the LED starts to flash rapidly turn the key to the OFF position. Connect wire to vehicle TECHNICAL SUPPORT INFORMATION ALL RIGHTS RESERVED OUTPUT INPUT web resources: www.xpresskit.com www.xpressvip.com www.directechs.com 6 The LED will turn off to indicate the module has been programmed. OFF Connect wire to Remote-Starter/Alarm Copyright © 2010, DIRECTED ELECTRONICS INC 4 7 WARNING: Connector 2 can be easily plugged in backwards. 4 N.C. 9 1 Press the programming switch while inserting the main wires harness (CONN 1) into the DLPK module. The LED will illuminate to indicate you are in programming mode, release the programming button. Wires located in driver kick panel, PIN-4, bottom row of 21-pin GREEN plug. (CAN SW) Data Brown Yellow White/Black Gray Green Brown Violet/Black Orange/Green Orange/Brown Blue Light Green Red/White Connector 3 (White, located at the back of the module): Make the connections 2 conn. N.C. 14 1 Connector 2 (White): Make the connections Cut off one plug of the D2D connector, connect the blue* wire to +12V and the black* wire to ground. *Wire colors may vary on the kit you have purchased. Orange/Brown Orange/Green 4 8 OFF Light Green 1 Orange White/Red Violet/White Blue/White White/Violet Lt. Green Pink Connector 1 (Black): Determine the type of installation: INSTALLATION WITH D2D INSTALLATION WITHOUT D2D +12V Ground Fuse Panel conn. 1.A 1.C conn. D2D (2 way) Connect: 7 1.B INSTALLATION WITHOUT D2D Yellow White/Black Gray Green Brown violet/Black Orange/Green Orange/Brown Blue Light Green Red/White Make the connections of the DLPK to the vehicle: N.C. D2D Cable 4 1 Hood Trigger Door Trigger Red/White INSTALLATION WITH D2D 1 8 14 conn. Front of the module Rev.: 2010113 N.C. Blue 14 WWW.XPRESSKIT.COM D2D (1 way) 1 Radio Off Transponder Bypass PK3, Passlock Slidding Door Defrost DLPK 3 Tach Start Enable Door Trigger Trunk Trigger Hood Trigger Lock Unlock Arm Disarm Trunk 2 Fonctionnal if equipped 2003-2007 U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product. IGN START The module is now ready for use. HONDA Accord Radio Off Transponder Bypass PK3, Passlock Portes Coulissantes Dégivrage Sièges chauffants Porte essence Contrôle portes Hayon arrière Signal de Frein Orange Contact Valise Blanc/Rouge Tach Violet/Blanc Programming Button N.C. conn. (-) Masse d’activation (status) 1 1 ~ Bleu/Blanc 2 Dégivrage Verrouillage Ignition 8 Blanc/Violet Vert pâle Rose Connect: Orange Jaune Blanc/Noir Gris Vert Violet/Noir 1 N.C. Déverrouillage Valise 1.B Connecteur 1 (Noir - 4 pins): Determinez le type d’installation: 1 Bleu* Noir* D2D Cable 1 conn. 4 N.C. 3 Blanc/Rouge Violet/Blanc Bleu/Blanc Blanc/Violet Vert pâle Rose Jaune Blanc/Noir Gris Brun Vert Orange/Vert Violet/Noir Orange/Brun Bleu Vert pâle Rouge/Blanc 14 Connecteur 2 (Blanc): Éffectuez les branchements Connecteur 3 (Blanc, situé au dos du module): Éffectuez les branchements Maintenez le bouton de programmation enfoncé en insérant le connecteur 1 dans le DLPK. Le DEL s'allume pour indiquer le début de la programmation, relâchez le bouton de programmation. Branchez le connecteur 2 (CONN. 2) ATTENTION: Ne pas brancher le connecteur à l'envers. 8 7 6 5 4 3 2 1 Branchez le connecteur 3 (CONN. 3) IGN 5 Tournez la clef en position ignition. START Brun/Rouge Copyright © 2010, DIRECTED ELECTRONICS INC ALL RIGHTS RESERVED SORTIE ENTRÉE web resources: www.xpresskit.com www.xpressvip.com www.directechs.com 6 Lorsque le DEL clignote rapidement, tournez la clef en position OFF. OFF Branchement du filage au véhicule TECHNICAL SUPPORT INFORMATION 4 7 Vue de dos du module Branchement du filage au démarreur à distance/Alarme 1 Déterminez le type d’installation (D2D ou non D2D) Pour l’installation D2D assurez vous de la présence du connecteur D2D sur le démarreur. Pour installation non D2D voir INSTALLATION SANS D2D. 21 20 19 18 17 16 15 14 13 12 11 10 9 1 OFF Brun N.C. 4 3 (CAN SW) Data N.C. 4 8 Connecteur 1 (Noir): Couper les 4 fils à l’extrémité de l’un des deux connecteurs D2D. Connecter le fil bleu* au +12 V et le fil noir* à la masse du véhicule. *La couleur des fils peut varier selon le kit. Orange/Brun Orange/Vert 1 7 2 conn. Fils situés dans le panneau latéral du côté chauffeur, PIN-4, dernier rang du connecteur vert de 21 PINS. Vert pâle Orange +12V Masse Panneau à fusible 1 1.A 1.C conn. D2D (2 way) Connect: Effectuez les connexions du DLPK au véhicule: 7 INSTALLATION SANS D2D Rev.: 2010113 Jaune Contact Capot Contact Porte Rouge/Blanc INSTALLATION AVEC D2D 1 Blanc/Noir Gris Brun Vert Violet/Noir Orange/Vert Orange/Brun Bleu Rouge/Blanc Vert pâle 14 conn. Vue de face du module WWW.XPRESSKIT.COM N.C. Bleu 14 8 Blanc/Rouge Violet/Blanc Bleu/Blanc Blanc/Violet Vert pâle Rose N.C. DLPK D2D (1 way) 1 Tach Active Démarreur Status de Porte Status de Valise Status de Capot 3 Verrouillage Déverrouillage Armement Désarmement Valise 2 Fonctionnel si équippé: 2003-2007 U p d at e A l e r t : F i r m w a r e updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of this product. IGN START Le DEL s'éteint pour indiquer que le module est programmé.