ASCO Model 184 Installation Manual
Transcription
ASCO Model 184 Installation Manual
Series 100 Model 184 (Edco CAT6-5POE) CAT6/CAT5 Power-Over-Ethernet Surge Protective Device Technical Documentation The ASCO Model 184 is designed to work on Category 5 Power-Over-Ethernet transmission lines as well as Category 6 applications. Ideal to protect expensive equipment against surges and transients entering a building on exposed transmission lines. Key Specs • Voltage: 0-57 VDC • Current: 350 mA • Connection: Input: female RJ-45 Output: female RJ-45 General Technical Specifications • Mounting: NA Operating Voltage 0-57 VDC Clamping Voltage 68 VDC Operating Current 350 mA Peak Surge Current *See Ordering Information for model number selection 60 A (10 x 1000 μs) Frequency Range 0 to 250 MHz Insertion Loss < 0.1 dB at 20 MHz SPD Technology Silicon Avalanche Diode (SAD) Connection Type Female-Female RJ-45 Jacks Operating Temperature -40°C to +85°C Dimensions (in / mm) 0.8˝ H x 1.0˝ W x 2.3˝ L [20.3 x 25.4 x 58.4 mm] Weight (oz / kg) 1 oz [0.02 kg] Warranty 1 year Features • Exceeds Cat 5 & 6 transmission values • CAT5 POE compatible • CAT6 compatible • Applications up to 57 VDC @ 350mA • 1 year warranty Caution Do not place this product in service on any signal line capable of supplying more than 350 mA continuously. Attention Ne pas placer ce produit dans le service sur une ligne de signal capable de fournir en permanence plus de 350 mA ampères. V DANGER! Only qualified personnel should install or service this system. Electrical safety pre-cautions must be followed when installing or servicing this equipment. To prevent risk of electrical shock, turn off and lock out all power sources to the unit before making electrical connections or servicing. Seulement le personnel qualifié doit installer ou maintenir ce systéme. Des précautions de sécurité en électricité doivent être suivis lors de l’installation ou de la maintenance de cet equipement. Pour eviter tout risque de choc électrique, débranchez et verouiller toutes les sources d’alimentation de cet equipement avant de. Certifications • IEEE802.3af compliant (POE) Installation Instructions 1. Mount the SPD as close as possible to the protected equipment. 2. Connect the supply cable (with RJ-45 connector) to the INPUT side of the SPD. 3. Complete the circuit by connecting the output of the SPD to the protected equipment. Circuit Diagram 2 2 Typical (4x) IN 1 Low Capacitance Neg Steering Diodes OUT 1 Silicon Avalanche Diodes Low Capacitance Pos Steering Diodes Ordering Information Dimensional Information MODEL Former Model Name 184D065S060SRJN0 184D065S060SRJN0 Edco CAT6-5POE-FF 0.8” [20.3] 184D065S060SRMN0 Edco CAT6-5POE-MF APPLICATION RJ-45 (female-to-female) RJ-45 (male-to-female) 2.3” [58.4] 1.0” [25.4] 14550 58th Street North Clearwater, Florida 33760 P (800) 237-4567 P (727) 535-6339 F (727) 539-8955 E [email protected] While every precaution has been taken to ensure accuracy and completeness herein, ASCO Power Technologies assumes no responsibility, and disclaims all liability, for damages resulting from use of this information or for any errors or omissions. Specifications are subject to change without notice. ID-50109 Rev- 07-16