System Display with Fan Control System
Transcription
System Display with Fan Control System
BEDIENUNGSANLEITUNG www.conrad.com System-Display mit Lüftersteuerung Version 09/05 ° Best.-Nr. 99 90 15 Bestimmungsgemäße Verwendung Das Produkt ist zum Einbau in einen Computer vorgesehen und zeigt über das Display verschiedene Informationen an, die über die mitgelieferte Software ausgewählt werden können. Weiterhin integriert ist eine automatische Lüftersteuerung für 4 Kanäle. Alle enthaltenen Firmennamen und Produktbezeichnungen sind Warenzeichen der jeweiligen Inhaber. Alle Rechte vorbehalten. Wenn Sie einen internen USB-Port nutzen wollen, so achten Sie auf die richtige Belegung der Anschlussstecker, andernfalls wird der das Produkt und auch das Mainboard zerstört In der Bedienungsanleitung zu Ihrem Mainboard finden Sie die Belegung der Stiftleisten eines internen USBPorts. • Lüfter können mit den 3poligen Anschlüssen verbunden werden. Alternativ liegen Adapterkabel für Lüfter mit 5.25"-Stromanschluss bei. • Verbinden Sie den 5.25"-Stromanschluss des zu Beginn angesteckten Spezialkabels mit einem passenden Stecker des ATX-Netzteils. • Kontrollieren Sie nochmals die Verbindung aller Kabel. Verlegen Sie die Kabel so, dass sie nicht in einen Lüfter des Computers gelangen, verwenden Sie Kabelbinder zur Fixierung. • Verschließen Sie das Computergehäuse und verbinden Sie Ihren Computer mit der Netzspannung und schalten Sie alle Geräte ein. Lieferumfang • Einschub • Kabelsatz • Schraubensatz • CD mit Treiber und Software • Engl. Anleitung des Herstellers • Dt. Kurzanleitung Merkmale • Einbau in 5.25"-Schacht eines PC-Gehäuses • Display mit Beleuchtung • USB-Anschluss für Ansteuerung des Displays • Software für Auswahl und Übertragung von Informationen ans Display (Steuerung des Displays ausschließlich über diese Software möglich; es wird ein aktuelles Windows-Betriebssystem benötigt, z.B. Windows XP) • Lüftersteuerung mit 4 Kanälen Einbau Falls Sie keine Fachkenntnisse für den Einbau besitzen, so lassen Sie den Einbau von einer FACHKRAFT oder einer entsprechenden Fachwerkstatt durchführen! Durch unsachgemäßen Einbau wird sowohl das Produkt als auch Ihr Computer und alle angeschlossenen Geräte beschädigt. Vorsicht, Lebensgefahr! Schalten Sie den Computer, in den das Produkt eingebaut werden soll und alle angeschlossenen Geräte aus und trennen Sie alle Geräte von der Netzspannung, ziehen Sie den Netzstecker! Das Ausschalten über den Ein-/Ausschalter genügt nicht! • Öffnen Sie das Gehäuse Ihres Computers und nehmen Sie den Gehäusedeckel vorsichtig ab. • Entfernen Sie die Abdeckung eines 5.25"-Einbauschachtes. Eventuell muss zusätzlich eine Metallabschirmung innen im Einbauschacht entfernt werden. Abhängig vom verwendeten Computergehäuse ist dazu die Entfernung der kompletten Frontblende erforderlich. • Achtung, verbinden Sie zuerst das mitgelieferte Spezial-Stromkabel (5.25"Anschluss auf 4poligen Mini-Stecker) mit dem zugehörigen Anschluss "C" (siehe engl. Anleitung des Herstellers, Seite 5) der Platine. Der Anschluss auf der Platine ist mit "JP3" bzw. "5V GND GND +12V" beschriftet). Der wie ein 3.5"-Stromanschluss aussehende Stecker auf der Platine dient als Anschluss für das USB-Kabel! Bei falschem Anschluss wird das Produkt zerstört, Verlust von Garantie/Gewährleistung! • Schließen Sie die anderen Kabel an. In der engl. Anleitung finden Sie dazu entsprechende Abbildungen. Je nachdem, ob Sie einen internen USB-Port auf dem Mainboard oder eine herkömmliche USB-Typ-A-Buchse nutzen wollen, können Sie das entsprechende USB-Anschlusskabel verwenden. OPERATING INSTRUCTIONS www.conrad.com System Display with Fan Control Version 09/05 ° Item-No. 99 90 15 • Fans can be connected with the 3-pin plugs. Alternatively, use the fan adapter cables with the 5.25" power connector, which have been supplied. • Connect the 5.25" power connector of the special power cable already connected to an appropriate plug on the ATX power unit. • Recheck all cable connections. Secure all cables so that they cannot become entangled in the fan of the computer. Use cable ties to fix them in place. Intended use This product is intended for installation in a computer and displays information which can be selected using the software supplied. An automatic fan control for 4 channels has also been integrated. • Close the computer case and connect your computer to the mains supply and switch all devices on. All company and product names mentioned in this document are registered trademarks of the respective owners. All rights reserved. Scope of delivery • If the computer does not start correctly, switch it off immediately and check all settings and cable connections. Before opening the computer case again, disconnect the computer from the mains supply (see above). • Insert • Cable set • Screw set • CD with driver and software • Engl. manufacturer's instructions • En. brief instructions Driver and software installation Treiber- und Software-Installation Features Tips and information Legen Sie die mitgelieferte CD in das entsprechende Laufwerk Ihres Computers ein. Nach dem Start der Hardwareerkennung findet Windows die passenden Treiber auf der CD und installiert sie. Danach ist die Software selbst zu installieren. Falls die Softwareinstallation nicht automatisch gestartet ist, führen Sie das Programm "Install.exe" auf der CD aus. Folgen Sie allen Anweisungen. Diese Vorgehensweise könnte sich bei neueren Versionen der CD evtl. ändern. • Insert into a 5.25" bay of a computer case • Display with lighting • USB connection for controlling the display • Software for selecting and transferring information on to the display (Controlling the display exclusively with this software is possible. A current Windows operating system is required, for example, Windows XP) • Fan control with 4 channels • Refer to the English version of the manual for extensive information on the different functions of the software. • The software can show a great variety of information on the display, for example, memory data, CPU data, time, etc. • There is also a plug-in to Winamp in the delivery scope so that the volume indicator and, if applicable, also the song title can be displayed. If Winamp is installed after the control software has been installed, the necessary plug-in must be copied manually into the plug-in directory for Winamp (see English version of manual, p. 21). Before Winamp data can be sent to the display, the plug-in must be activated. Also, in Winamp "Preferences" select the domain "Visualisation" under "Plug-ins" and activate the plug-in "LIS Control-Center". • A maximum current of about 0.8A is available for each fan. The use of fans with a greater current will destroy the product. • Do not adjust the plug-in jumper on the circuit board. • When Bluetooth is installed, it is possible that the software provided will no longer recognise the driver software of the device. The reason is that Bluetooth takes up many COM interfaces. Remedy: First, uninstall your Bluetooth adapter. Then, install the system display / fan control as described above. You can then reinstall your Bluetooth adapter. • With some systems which run on Windows XP the computer might not shut down properly. If this happens, on the first attempt to shut down the computer, only the display software will be exited (similar effects are, incidentally, also possible with other software/hardware). Remedy: Simply click the "Start" button again and then shut down the computer. • Startet der Computer nicht richtig, so schalten Sie ihn sofort aus und kontrollieren Sie sämtliche Einstellungen und Kabelverbindungen. Vor dem erneuten Öffnen des Computergehäuses ist der Computer von der Netzspannung zu trennen, siehe oben! Tipps & Hinweise Installation • In der engl. Anleitung finden Sie umfangreiche Hinweise zu den verschiedenen Funktionen der Software. • Die Software kann viele verschiedene Informationen auf das Display ausgeben, beispielsweise Daten zu Speicher, CPU, Uhrzeit uvm. • Im Lieferumfang enthalten ist auch ein Plug-In zu Winamp, so dass die Aussteuerungsanzeige und ggf. auch der Liedtitel angezeigt werden können. Falls Winamp erst nach der Installation der Steuersoftware installiert wird, so muss das benötigte Plug-In von Hand in das Plug-In-Verzeichnis von Winamp kopiert werden, siehe engl. Anl. auf Seite 21. Damit Winamp Daten an das Display liefert, muss das Plug-In gestartet werden. In den Eigenschaften ("Preferences") von Winamp ist dazu unter "Plug-ins" der Bereich "Visualization" auszuwählen und das Plug-In "LIS Control-Center" zu starten. • Pro Lüfteranschluss steht ein Maximalstrom von ca. 0,8A zur Verfügung. Die Verwendung von Lüftern mit höherem Strom führt zur Zerstörung des Produkts. • Die Steckbrücken auf der Platine dürfen nicht verstellt werden. • Bei vorhandenem Bluetooth ist es möglich, dass die mitgelieferte Software die Treibersoftware das Gerät nicht mehr erkennt. Grund ist, dass Bluetooth viele COM-Schnittstellen belegt. Abhilfe: Deinstallieren Sie zuerst Ihren Bluetooth-Adapter. Danach ist das SystemDisplay/Lüftersteuerung zu installieren, wie oben beschrieben. Abschließend können Sie Ihren Bluetooth-Adapter wieder installieren. • Bei manchen Systemen mit Windows XP kann es unter Umständen vorkommen, dass der Computer nicht korrekt herunterfährt und sich ausschaltet. Beim ersten Versuch, den Computer herunterzufahren, wird dabei nur die Displaysoftware beendet (ähnliche Effekte sind übrigens auch mit anderer Software/Hardware möglich). Abhilfe: Klicken Sie einfach ein zweites Mal auf den "Start"-Knopf und fahren Sie den Computer nun herunter. • Open the case of your computer and remove the cover carefully. Entsorgung • Connect the other cables. Corresponding illustrations for this are in the English version of the manual. Depending on whether you choose to use an internal USB port on the motherboard or a conventional USB type A port, you can use the corresponding USB connecting cable. Entsorgen Sie das Produkt am Ende seiner Lebensdauer gemäß den geltenden gesetzlichen Bestimmungen. If you have no specialist knowledge of installation procedures, arrange for the installation to be carried out by a SPECIALIST or an appropriate specialist shop. Incorrect installation will damage the product, your computer and all connected devices. Caution, danger of fatal injury! Switch off the computer in which the product is to be installed and all connected devices. Disconnect all devices from the mains supply and pull out the mains plug. Switching off using the on/off switch is not enough! • Remove the cover of an empty 5.25" drive bay. There may be metal shielding in the drive bay, which also needs to be removed. Depending on the computer case, the front panel might have to be removed completely. • Note: First connect the special power cable (5.25" connector to 4-pin mini plug) to port "C" (see page 5. of the manufacturer's manual in English) on the circuit board. The port on the circuit board is labelled "JP3" or "5V GND GND +12V". Insert the CD supplied in the appropriate drive of your computer. After starting hardware recognition, Windows finds the correct driver on the CD and installs it. After that, you can install the software yourself. If the software installation program does not start automatically, open the file "Install.exe" on the CD. Follow all instructions. This procedure may differ for later versions of the CD. Disposal When the device has become unusable, dispose of it in accordance with the applicable statutory regulations. The plug that looks like a 3.5" power connector on the circuit board is the connector for the USB cable. The product will be destroyed if it is incorrectly connected up, and warranty/guarantee will lapse. • Slide the module into the bay of the computer case and screw it in tightly. • Connect the cables to their corresponding ports. • Schieben Sie das Modul in den Einbauschacht des PC-Gehäuses und schrauben Sie es fest. • Verbinden Sie die Kabel mit den entsprechenden Anschlüssen. Diese Bedienungsanleitung ist eine Publikation der Conrad Electronic GmbH, Klaus-Conrad-Straße 1, D-92240 Hirschau. Diese Bedienungsanleitung entspricht dem technischen Stand bei Drucklegung. Änderung in Technik und Ausstattung vorbehalten. © Copyright 2005 by Conrad Electronic GmbH. Printed in Germany. If you choose to use an internal USB port, make sure you identify the correct pin assignment of the connector. Otherwise, the product and the motherboard will be destroyed. Refer to the manual for your motherboard for the pin assignment of an internal USB port. These operating instructions are published by Conrad Electronic GmbH, Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany. The operating instructions reflect the current technical specifications at time of print. We reserve the right to change the technical or physical specifications. © Copyright 2005 by Conrad Electronic GmbH. Printed in Germany. MODE D’EMPLOI Afficheur système avec commande de ventilateur www.conrad.com Version 09/05 ° N° de commande 99 90 15 Utilisation conforme Ce produit est conçu pour être monté sur un ordinateur et affiche sur écran différentes informations pouvant être sélectionnées via le logiciel fourni avec le produit. Une commande de ventilateur automatique pour 4 canaux est en outre intégrée au produit. Tous les noms de sociétés et toutes les désignations de produits sont des marques déposées de leurs propriétaires respectifs. Tous droits réservés. Contenu de la livraison • Tiroir • Faisceau de câbles • Kit de vis • CD avec pilote et logiciel • Mode d'emploi en anglais du fabricant • Mode d'emploi condensé en allemand Si vous souhaitez utiliser un port USB interne, veillez à l'affectation correcte des connecteurs, sinon le produit et la carte mère seront endommagés. Vous trouverez l'affectation des barrettes à broches d'un port USB interne dans le mode d'emploi de votre carte mère. • Les ventilateurs peuvent être reliés à des raccordements à 3 pôles. Sinon, vous pouvez utiliser les câbles adaptateurs pour ventilateur avec raccordement électrique de 5,25" fournis avec le produit. • Reliez le raccordement électrique de 5,25" du câble spécial branché au début avec un connecteur correspondant du bloc d'alimentation ATX. • Contrôlez à nouveau la liaison de tous les câbles. Disposez les câbles de manière à ce qu'ils ne pénètrent pas dans un ventilateur de l'ordinateur, utilisez des serrecâbles pour les fixer. • Refermez ensuite le boîtier de l'ordinateur, branchez l'ordinateur sur la tension secteur et mettez tous les appareils en marche. • Si votre ordinateur ne démarre pas correctement, éteignez-le immédiatement et contrôlez tous les réglages, ainsi que les raccordements de câbles. Avant d'ouvrir à nouveau le boîtier de votre ordinateur, débranchez-le de la tension secteur, voir plus haut ! Installation des pilotes et du logiciel Caractéristiques • Montage dans une baie de 5,25 pouces dans un boîtier d'ordinateur • Ecran avec éclairage • Raccordement USB pour commande de l'écran • Logiciel de sélection et de transfert d'informations à l'écran (commande de l'écran uniquement possible via ce logiciel ; système d'exploitation requis : version Windows actuel, par ex. Windows XP) • Commande de ventilateur à 4 canaux Insérez le CD fourni dans le lecteur correspondant de votre ordinateur. Après le démarrage de reconnaissance de matériel, Windows trouve le pilote adéquat sur le CD et l'installe. Installez ensuite le logiciel. Au cas où l'installation de logiciel ne démarre pas automatiquement, exécutez le programme « Install.exe » sur le CD. Suivez toutes les instructions. Il est possible que la méthode d’installation soit différente avec des versions plus récentes du CD. Conseils & indications Montage Si vous n'avez pas les connaissances spécialisées nécessaires pour le montage, veuillez confier cette opération à un SPECIALISTE ou à un atelier spécialisé ! Un raccordement incorrect est susceptible d'endommager non seulement le produit, mais aussi votre ordinateur et tous les appareils qui y sont raccordés. Attention, danger de mort! Eteignez l'ordinateur sur lequel le produit doit être monté, ainsi que tous les appareils connectés, et les débrancher du secteur en retirant les fiches des prises de courant ! La mise hors circuit de l'appareil par le biais de l'interrupteur marche/arrêt ne suffit pas ! • Ouvrez le boîtier de votre ordinateur et retirez son couvercle avec précaution. • Retirez le cache du logement de montage de 5,25". Il est possible qu'une protection métallique à l'intérieur du logement doivent également être retirée. A cet effet, en fonction du boîtier de PC utilisé, il peut être nécessaire de retirer l'ensemble du cache avant. • Attention, reliez en premier le câble électrique spécial fourni avec le produit (raccordement 5,25" sur un mini-connecteur à 4 pôles) au raccordement « C » correspondant (voir le mode d'emploi en anglais du fabricant, page 5) de la platine. Le raccordement sur la platine porte l'inscription « JP3 »ou « 5V GND GND +12 V »). Le connecteur sur la platine qui ressemble à un raccordement électrique 3,5" sert de raccordement au câble USB ! En cas de mauvais raccordement, le produit est endommagé, ce qui annule toute garantie ! • Raccordez les autres câbles. Vous trouverez les illustrations correspondantes dans le mode d'emploi en anglais. En fonction de l'utilisation envisagée : port USB interne sur la carte mère ou douille USB traditionnelle de type A, vous pouvez utiliser le câble de raccordement USB correspondant. • Insérez le module dans le logement du boîtier d'ordinateur et vissez-le. • Reliez les câbles aux raccords correspondants. • Dans le mode d'emploi anglais, vous trouverez des remarques complètes relatives aux différentes fonctions du logiciel. • Le logiciel peut afficher de nombreuses informations différentes à l'écran, par exemple des données relatives à la mémoire, la CPU, l'horloge etc. • Le produit est livré avec un Plug-In pour Winamp, pour permettre l'affichage de contrôle de niveau et éventuellement le titre du morceau. En cas d'installation Winamp ultérieure à celle du logiciel de commande, vous devez copier le Plug-In requis dans le répertoire Plug-In de Winamp, voir le mode d'emploi en anglais page 21. Pour que Winamp fournisse des données à l'écran, vous devez démarrer le PlugIn. Pour cela, sous le point de menu Propriétés (« Favoris ») de Winamp, sous « Plug-ins », sélectionnez le champ « Visualisation », et démarrez le Plug-In « LIS Control-Center ». • Un courant maximum d'env. 0,8 A est disponible pour chaque prise ventilateur. L'utilisation de ventilateurs avec un courant supérieur endommage le produit. • Ne modifiez pas les cavaliers sur la platine. • Si Bluetooth est installé, il est possible que le logiciel fourni ne reconnaisse plus le logiciel pilote de l’appareil puisque Bluetooth occupe de nombreuses interfaces COM. Solution : désinstallez tout d’abord votre adaptateur Bluetooth, puis installez votre afficheur système/commande de ventilateur comme décrit ci-dessus. Vous pouvez ensuite réinstaller votre adaptateur Bluetooth. • Il est possible qu’avec certains systèmes, sous Windows XP, le système de votre ordinateur ne s’arrête pas correctement et que votre ordinateur s’éteigne. Lorsque vous essayez la première fois d’arrêter le système de votre ordinateur, seul le logiciel d’affichage s’éteint (des effets similaires sont d’ailleurs également possibles avec d’autres logiciels/matériels). Solution : appuyez une seconde fois sur le bouton « Start » (démarrer), puis arrêtez le système de votre ordinateur. Elimination des éléments usés Il convient de procéder à l'élimination du produit au terme de sa durée de vie conformément aux prescriptions légales en vigueur. Cette notice est une publication de la société Conrad Electronic GmbH, Klaus-Conrad-Straße 1, D-92240 Hirschau/Allemagne. Cette notice est conforme à la règlementation en vigueur lors de l´impression. Données techniques et conditionnement soumis à modifications sans aucun préalable. *09-05/HK © Copyright 2005 par Conrad Electronic GmbH. Imprimé en Allemagne.