USB-Kartenleser für CompactFlash-/ ° Smartmedia-/SD
Transcription
USB-Kartenleser für CompactFlash-/ ° Smartmedia-/SD
BEDIENUNGSANLEITUNG www.conrad.de Version 04/02 USB-Kartenleser für CompactFlash-/ ° Smartmedia-/SD-/MMC-Speicherkarten Best.-Nr. 97 60 99 Bestimmungsgemäße Verwendung Das Produkt kann an einen USB-Port eines PCs angeschlossen werden und dient dort zum Lesen und Beschreiben von Speicherkarten in den Formaten CompactFlash, Smartmedia, SD und MMC. Einstecken/Entnehmen von Speicherkarten Stecken Sie die Speicherkarte korrekt in den zugehörigen Einschub des USBKartenlesers; nur eine Orientierung ist richtig. Wenden Sie beim Einstecken keine Gewalt an! Wenn Lese-/Schreibzugriffe auf die Speicherkarte erfolgen, so warten Sie, bis diese abgeschlossen sind. Ziehen Sie erst danach die Speicherkarte heraus. Wird die Speicherkarte während einem Lese-/Schreibzugriff herausgezogen, so können die Daten auf der Speicherkarte beschädigt werden, möglicherweise ist danach sogar eine neue Formatierung der Speicherkarte erforderlich. An- und Abstecken des USB-Kartenlesers Entnehmen Sie vor einem An- bzw. Abstecken des USB-Kartenlesers die evtl. eingesetzten Speicherkarten; ansonsten können Daten auf den Speicherkarten beschädigt werden. Lieferumfang Auslesen/Beschreiben von Speicherkarten • USB-Kartenleser • CD mit Treiber (für Windows ME/XP nicht nötig!) • Bedienungsanleitung Jeder der 3 Einschübe wird wie ein herkömmliches Wechseldatenträger-Laufwerk eingebunden. Drei zusätzliche Laufwerksbuchstaben werden von Windows automatisch vergeben. Merkmale • • • • Ein Einschub für CompactFlash-Speicherkarte Ein Einschub für Smartmedia-Speicherkarte Ein Einschub für SD-/MMC-Speicherkarte LEDs für Anzeige des eingelegten Speicherkartentyps (LED an) bzw. Lese/Schreibzugriff (LED blinkt) • Zum Betrieb ist mindestens Windows 98 nötig Im Datei-Explorer können Sie nun die Daten auf der Speicherkarte auslesen (oder Daten auf die Speicherkarte speichern), genauso wie von Festplatte oder Diskettenlaufwerk. Verzeichnis-Strukturen auf der Speicherkarte sollten Sie jedoch nicht löschen, da sie sonst in MP3-Player, Kamera, PDA usw. wieder formatiert werden muss. Tipps & Hinweise Anschluss & Software-Installation Stecken Sie den USB-Kartenleser in einen freien USB-Port Ihres PCs ein. Bei Windows ME bzw. XP sind die Treiber bereits im System enthalten, die mitgelieferte Treiber-CD ist nicht nötig! Folgen Sie allen Anweisungen von Windows ME/XP. Bei der Verwendung einer CompactFlash-Festplatte ist ein High-Power-USB-Port erforderlich; dies ist ein USB-Port, der einen Strom von 500mA liefern kann (z.B. der USB-Port eines Motherboards oder USB-Hubs mit Netzteil). Beim Löschen oder Beschreiben von Speicherkarten im SD-Format ist darauf zu achten, dass der Schreibschutz ausgeschaltet ist. Diese Bedienungsanleitung ist eine Publikation der Conrad Electronic GmbH, Klaus-Conrad-Straße 1, D-92240 Hirschau. Bei Windows 98 bzw. Windows 98SE legen Sie die mitgelieferte Treiber-CD in Ihr CD-ROM-Laufwerk ein. Folgen Sie allen Anweisungen von Windows. OPERATING INSTRUCTIONS www.conrad.de Inserting/Removing Memory Cards Put a memory card correctly into the insert of the USB-card reader; only one orientation is correct. Version 04/02 USB-Card Reader for CompactFlash-/ Smartmedia-/SD-/MMC-Memory Cards ° Item-No. 97 60 99 Do not force the card into the insert! If there are reading or writing accesses in process on the memory card wait until they are completed. Only then pull out the memory card. If the memory card is pulled out during a reading or writing access the data on the memory card might be damaged, it might even become necessary to format the memory card once more. Prescribed Use The product may be connected to an USB-port of a PC and serves for reading and writing on memory cards in the formats CompactFlash, Smartmedia, SD and MMC. Scope of Delivery • USB-card reader • CD with driver (not required for Windows ME/XP!) • Operating instructions Features • • • • Insert for a CompactFlash memory card Insert for a Smartmedia memory card Insert for a SD- /MMC-memory card LEDs for displaying the inserted type of memory card (LED on) or reading/writing access (LED is flashing) • Operation requires at least Windows 98 Connection & Software Installation Plugging in and Disconnecting the USB-Card Reader Remove the inserted memory card, if any, prior to plugging in or disconnecting the USB-card reader; otherwise the data stored on the memory card may be damaged. Reading out/Writing on Memory Cards Every single one of the 3 inserts is integrated like a conventional running carriage for exchangeable data carrier. Three additional letters for running carriages are automatically assigned by Windows. In the file explorer you may now read out data on the memory card (or store data on the memory card) like you do with a hard disk or a diskette running carriage. The structure of the dictionaries on the memory card, however, should not be changed as otherwise they have to be formatted again when used in a MP3-player, camera, PDA, etc. Tips & Notes When using a CompactFlash hard disk a High-Power-USB-port is necessary, this is a USB-port which is able to supply current of 500mA (e.g. USB-port of a motherboard or USB-hub with mains unit). Plug the USB-card reader into a free USB-port of your PC. With Windows ME or XP the drivers are included in the system, the supplied driverCD is not required! Follow all instructions of Windows ME/XP. With Windows 98 or Windows 98SE insert the supplied driver-CD in the CD-ROMrunning carriage. Follow all instructions of Windows. When writing on or deleting memory cards in the SD-format make sure that the write protection is deactivated. These operating instructions are published by Conrad Electronic GmbH, Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany. MODE D’EMPLOI www.conrad.de Introduire/retirer les cartes mémoires Introduisez la carte mémoire en faisant attention à la bonne orientation dans la baie du lecteur de cartes USB; une seule orientation est correcte. Version 04/02 Lecteur de carte USB pour cartes mémoires flash/smartmedia/SD/MMC ° N° de commande 97 60 99 Utilisation prévue Le présent produit est prévu pour être connecté à un port USB de micro-ordinateur et permet la lecture de et la mémorisation sur des cartes mémoires des formats Compactflash, Smart-Media, SD et MMC. Contenu de l’emballage • Lecteur de cartes USB • Cédérom de pilotage (inutile pour Windows ME/XP !) • Notice d’emploi Ne forcez pas en introduisant la carte ! Attendez avant de retirer la carte mémoire que les opérations de lecture/écriture sur la carte mémoire soient bien terminées. Retirez la carte mémoire seulement après. Si vous enlevez la carte pendant la lecture / l’écriture, vous risquez d’endommager les données mémorisées sur la carte et même qu’il faille re-formater celle-ci à nouveau. Connexion/déconnexion du lecteur de cartes USB Avant toute connexion / déconnexion du lecteur de cartes USB, veuillez retirer toute carte mémoire y étant introduite encore, sinon vous risquez d’endommager les données qu’elle contient. Lecture / enregistrement de cartes mémoire Chaque baie du présent lecteur de cartes USB est traitée comme un support de données amovible ordinaire. Trois lettres de lecteur supplémentaires sont attribuées automatiquement par Windows . Caractéristiques • • • • une baie pour carte mémoire Compactflash une baie pour carte mémoire Smart-Media une baie pour carte mémoire SD/MMC témoins indiquant le type de carte introduite (voyant allumé) ou la lecture/mémorisation (voyant clignotant) • pour le bon fonctionnement, Windows 98 au moins est nécessaire Branchement et installation du logiciel Introduisez le lecteur de cartes USB dans un port USB libre de votre micro-ordinateur. Dans Windows ME ou XP, les pilotes sont déjà intégrés au système et le CD pilote joint est inutile ! Suivez toutes les instructions données par Windows ME/XP. Pour Windows 98 ou Windows 98SE, mettez le CD pilote dans votre lecteur de CD. Suivez toutes les instructions données par Windows. A l'aide de l'explorateur de fichiers, vous pouvez maintenant lire les données se trouvant sur la carte mémoire (ou enregistrer des données sur celle-ci), de la même manière que sur le disque dur ou sur le lecteur de disquettes. Il est cependant préférable de ne pas effacer l'arborescence de dossiers installée sur la carte mémoire, car autrement elle devra être reformatée sur le lecteur MP3, le caméscope, l’assistant personnel etc. Trucs & astuces Si vous utilisez un disque dur compact-flash, un port de puissance élevée est nécessaire; ceci est un port pouvant fournir un courant de 500 mA (comme par ex. le port USB d'une carte mère ou d'un concentrateur USB avec son propre bloc d'alimentation). Cette notice est une publication de la société Conrad Electronic GmbH, *04-02/36-WM Klaus-Conrad-Straße 1, D-92240 Hirschau/Allemagne.