angie 00-3543-bw-bwu - Leds-C4
Transcription
angie 00-3543-bw-bwu - Leds-C4
ANGIE 00-3543-BW-BWU IN TECHNICAL CHARACTERISTICS The photograph may not match the reference exactly. Please read the product description to identify the finish. Type: Pendant IP Protection degrees: IP20 Location: DRY Light source 1: 1 x E26 MAX 100W Maximum lamp length: 200.00 mm Maximum lamp diameter: 150.00 mm Total power consumption (W): 100 Voltage / Frequency: 120V/60Hz Units per box: 1 Pes net (lb): 8.28 EAN: 8435381436933 MATERIALS / FINISHES Download photometric file .ldt /.ies Structure material: Steel Polycarbonate Diffuser material: ABS Structure finish: Matt white Transparent Diffuser finish: LEDS-C4 reserves the right to make the necessary technical changes they deem adequate, in order to improve the features of the product. Please consult the sales team to clarify any doubt. White (+34) 973 468 100 [email protected] www.leds-c4.com Luminaire Code 00-3543-BW-BW Name Colgante ANGIE 100W A55 E27 Line - LEDS-C4 Measurem. Code 00-3543-BW-BW Name Colgante ANGIE 100W A55 E27 Date 12-06-2015 Lamp Code Number Position Efficiency 45.83% Coordinate system CG Total Flux Maximum value 242.79 cd Position C=15.00 G=25.00 Double Symmetrical 500 mm 280 mm Height Height STANDAR GOC 100W O 1 Universal 1340.00 lm Round Luminaire Round Luminous Area Diam. Diam. Horizontal Luminous Area Emitting area on Plane 0° Emitting area on Plane 90° 0.061575 m2 0.000000 m2 0.000000 m2 Emitting area on Plane 180° Emitting area on Plane 270° Glare area at 76° 0.000000 m2 0.000000 m2 0.014896 m2 Symmetry Type Measurement Distance Double Symmetrical 6.44 Maximum Gamma Angle Measurement Flux 180 1271.00 lm Operator Temperature Humidity Notes Asselum T2 25.00 °C 54.00 % Source voltage Source current Photocell 230.00 V Prc Luminaire Lamps Code Name STANDAR GOC 100W O STANDAR GOCCIA 100W E27 OPALE Line PHILIPS 2005 ILCOS IA,IB,IC C.I.E. F UTE 440 mm 0 mm 55 79 94 86 46 0.39 D + 0.06 T D DIN 5040 B NBN Flux [lm] 1340.00 Pow. [W] Q.ty 100.00 1 B41 BZ 3 / 0.8 / BZ 4 Diam=500mm 90 Gamma Angles 180° 120° 0 50 105° 105° 180 270 90° 90° C Halfplanes 180.0 0.0 270.0 90.0 50 75° 75° 100 60° 60° 150 ULOR 6.46 % DLOR 39.37 % RN 14.10 % 45° 45° 200 cd 250 30° LITESTAR (c)OxyTech Srl www.oxytech.it 15° 0° 15° 30° Page 1 LEDS, C4 S.A. CIF/VAT: A-59.410.910 C/ Afueras s/n -TORA- 25750 (LLEIDA) SPAIN TEL: 34 (73) 46 81 02 FAX: 34 (73) 46 81 06 SHEET: 1/1 EDITION: 01 REF: 00-3543U FIGURE Nº 1. UNPACK THE FIXTURE: CHECK THE CONTENTS OF THE BOX. YOU SHOULD RECEIVE: FIGURE Nº 1. DÉBALLER LE PLAFONIER: VÉRIFIER LE CONTENU DU CARTON, VOUS DEVEZ RECEVOIR: FIGURE 7 FIGURE 6 FIGURE 8 INSTALLATION INSTRUCTIONS FOR HANGING FIXTURES FIGURE 3, 4 AND 5 MOUNTING HARDWARE. NOTE: TEST THE CONNECTOR BY GENTLY PULLING IT. IF IT PULLS OUT THE CONNECTION, TRY AGAIN TILL YOU HAVE A FIRM CONNECTION. MAKE SURE NO BARE STRANDS OF WIRE STICK OUT FROM UNDER THE CONNECTORS. WHITE OR MARKED WIRE FROM FIXTURE WHITE WIRE FROM OUTLET BOX FIGURE 3 BLACK OR UNMARKED WIRE BLACK FIGURE 4 FIGURE 5 INSTRUCTIONS D'INSTALLATION POUR PLAFONIERS FIGURE 3, 4 ET 5 MONTAGE DE L'ÉQUIPE. IMPORTANT: ESSAYER DE TIRER LE CÂBLE D'ALIMENTATION DOUCEMENT.S'IL SORT DE LA CONNECTION, IL FAUDRAIT ASSURER QUE LA CONNECTION SOIT FERME. S'ASSUSER QUE LES FILS DES CÂBLES NE SONT PAS À DÉCOUVERT DU CONNECTEUR. CÂBLE BLANC OU MARQUÉ DU PLAFONIER CÂBLE BLANC DE LA BOÎTE FIGURE 3 CÂBLE NOIRE OU NOU-MARQUÉ FIGURE 4 NOIRE FIGURE 5 CAUTION: ATTENTION: "Warning", "This product is to be installed by a qualified electrician only." "Suitable for dry locations only" "Attention", le raccordement électrique sera effectué par un téchnicien électricien qualifié" "Adéquat seulement en lieux secs." CAUTION: 1.- Wrong lighting installation can be dangerous for your safety. 2.- Before starting, disconnect the power by turning off the general switch of the electric installation. 3.- Install light bulbs (not provided) that must not exceed markings on the fixture. 4.- To change the bulbs, disconnect the power by turning off the general switch and wait for the bulbs cool down. INSTALLATION: 1.- Make electrical connections, carefully read the Electrical Connection section. 2.- Assemble lighting onto the outlet box as shown on fig. 6, & 7. ELECTRICAL CONNECTIONS: (See fig. 3,4 y 5) 1.- Connect the white wire from the fixture to the white wire of the electric installation. 2.- Connect the black wire from the fixture to the black wire of the electric installation. 3.- Connect the grounding conductor from the fixture to the grounding wire of the electric installation. 4.- Spread out the electrical wires so that the black ones are on one side of the outlet box and the white ones are on the other side, and carefully introduce them into the outlet box. ATTENTION: 1. Une mauvaise installation peut compromettre votre sécurité. 2. Déconnecter la tension du réseau d'alimentation avant de réaliser toute opération. 3. Installer les ampoules (non fournies), ne pas utiliser d'ampoules d'un autre type ou d'une puissance supérieure à celle indiquée sur l'étiquette de la lampe. 4. Pour changer les ampoules, déconnecter la tension du réseau d'alimention et laisser refroider les ampoules. INSTALLATION: 1. Connecter au réseau, lire attentivement la section de "Raccordements électriques" 2. Installer l'appareil à la boîte de distribution comme indiqué dans les dessins 6 et 7. RACCORDEMENTS ÉLECTRIQUES (dessins 3,4 et 5) 1. Connecter le câble blanc de l'appareil au câble blanc de l'installation électrique. 2. Connecter le câble noir de l'appareil au câble noir de l'installation électrique. 3. Connecter le câble conducteur de prise de terre au câble de prise de terre de l'installation électrique. 4. Distribuer les câbles pour que tout le câblage noir soit par dehors et le câblage blanc soit par dedans. Ajuster et immobiliser à la boîte sans coincer aucun câble.