ASCO Model 130 Data Sheet
Transcription
ASCO Model 130 Data Sheet
Series 100 Model 130 (Edco PB Series) Intercom/Speaker Punch Block Protection Surge Protective Device Technical Documentation The ASCO Model 130 modules are solid-state protectors for Intercom Extension Pairs. As a new alternative to the “Model 132,” the standard ASCO intercom protector, the Model 130 adds fusing and a new component layout. These hybrid protectors are intended to be used in conjunction with the ASCO MGBW ground rail and a standard M150 punch down block. The Model 130 modules feature solid-state resettable fuses (PTCs) between the protected equipment and the over voltage clamping components. This unique design prevents problems with “All-Call” in the event of catastrophic protector failure. Key Specs • Voltage: 0-12 VDC, 0-56 VDC • Current: 150mA • Connection: Clips into 66M1-50 Block using MGBW ground rail. • Mounting: MGBW ground rail *See Ordering Information for model number selection General Technical Specifications Operating Voltage 130D021S200SPDN0 = 12 VDC 130D070S500MPDN0 = 56 VDC Features Clamping Voltage 130D021S200SPDN0 = 21 VDC 130D070S500MPDN0 = 70 VDC • Over current protection Operating Current 0.15 A Peak Surge Current 130D021S200SPDN0 = 0.2 kA 130D070S500MPDN0 = 0.5 kA Frequency Range 0 to 20 MHz Insertion Loss SPD Technology < 0.1 dB at 20 MHz • Replaces bridging clips on M1-50 bock • Utilizes MGBW grounding rail • 5 year warranty 130D021S200SPDN0 = SAD w/ Series PTC 130D070S500MPDN0 = MOV w/ Series PTC Connection Type Clip to M1-50 Punch Down Block Operating Temperature -40°C to +85°C Dimensions (in / mm) 1.25˝ H x 0.4˝ W x 2.8˝ L [31.75 x 10.16 x 71.12 mm] Weight (oz / kg) 1 oz [0.03 kg] Certifications UL497B Caution The hybrid design of this product includes series resistance. Do not place this product in service on any signal line capable of continuously supplying more than 150 mA. Attention La conception hybride de ce produit inclut la résistance en série. Ne pas placer ce produit dans le service sur une ligne de signal capable de fournir en permanence plus de 150 mA. V DANGER! Only qualified personnel should install or service this system. Electrical safety pre-cautions must be followed when installing or servicing this equipment. To prevent risk of electrical shock, turn off and lock out all power sources to the unit before making electrical connections or servicing. Seulement le personnel qualifié doit installer ou maintenir ce systéme. Des précautions de sécurité en électricité doivent être suivis lors de l’installation ou de la maintenance de cet equipement. Pour eviter tout risque de choc électrique, débranchez et verouiller toutes les sources d’alimentation de cet equipement avant de. Certifications • UL 497B Installation Instructions PROTECTED SIDE UNPROTECTED SIDE (Equipment Side) (Field Side) Protection Module MGBW M1-50 Block 10 AWG wire to building approved ground – keep short. Note: DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. Ordering Information MODEL Former Model Name 130D021S200SPDN0 Edco PBCLN 130D070S500MPDN0 Edco PBSPK APPLICATION Call-In Circuit Speaker Circuit ACCESSORIES Former Accessory Name MGBW MGBW-LUG Ground Rail for 66M1-50 Block Installation 14550 58th Street North Clearwater, Florida 33760 P (800) 237-4567 P (727) 535-6339 F (727) 539-8955 E [email protected] While every precaution has been taken to ensure accuracy and completeness herein, ASCO Power Technologies assumes no responsibility, and disclaims all liability, for damages resulting from use of this information or for any errors or omissions. Specifications are subject to change without notice. ID-50114 Rev- 07-16