franche-comte

FRANCHE-COMTE
A harmonious large shape
Large Format Small Curve Tile
MORE POWER TO YOUR ROOF
44 cm
Base de 5 cm de large
FRANCHE-COMTE
26,5 cm
Overall dimensions in cm
3 Contour precision
3 Fitting tolerances
3 Curved flow area
TECHNICAL CHARACTERISTICS
Type
Number of tiles per m2
Unit weight
Weight per m2
Overall length Overall width Linear cover
Theorical gauge
Longitudinal fitting tolerance
Transversal fitting tolerance
Linear metre of battens/m2
Laying
Product standard
Application standard
Silicone product
Number of tiles per pallet
Weight per pallet
TUILES DE TERRE CUITE
Classe 1 d’imperméabilité
Méthode E
d’essais de résistance au gel subis
PRESCRIPTION RECOMMENDATION
www.marque-nf.com
The tile shall be in terracotta, from the large format small curve tile family,
Interlocking relief clay tile, large format,
double interlocking and double overlap, more or less 12,6 pieces per square meter,
double interlocking, double overlap
type Franche-Comté from Monier or similar.
≈ 12,6
Its fitting tolerance shall be 1,4 cm long and 0,4 cm transverse. It shall be laid
≈ 3,4 kg
in straight joints from right to left, on battens according to the standard
≈ 42,8 kg
of the NF P 31-202 [DTU 40-21].
≈ 44 cm
Its installation shall be carried out using all parts specially designed
≈ 26,5 cm
for dry mortarless laying of ridges and edges as specified in the DTU.
≈ 21,9 cm
≈ 36,3 cm
± 0,7 cm*
30 YEARS
± 0,2 cm*
This tile has been developed
and tested in the wind
2,8 ml
tunnel at the Monier
M
Technical Center.
FROST
Laid with straight joints right to left
RESISTANCE
CLAY TILES
M
Class 1 watertightness
NF EN 1304
Method E
CONCRETE ROOF TILE
CONCRETE ROOF TILE
freezing resistance trials carried oubis
NF P 31-202 [DTU 40.21]
* Usual fitting tolerance stated apply from actual average gauges and widths checked on delivery as per DTU.
An additive is required for sealing
30
300
For YEARS
any projects developed within the context of an HQE® approach, an Environmental
1020 kg
and Health Declaration Sheet for this tile is available on request.
gUarantEE
www.marque-nf.com
www.marque-nf.com
TUILES DE TERRE CUITE
Classe 1 d’imperméabilité
Méthode Classe Montagne
d’essais de résistance au gel subis
www.marque-nf.com
FROST
RESISTANCE
Minimum de 15 mm de large
COLOR KEY
TUILES DE TERRE CUITE
Classe 1 d’imperméabilité
Méthode E
d’essais de résistance au gel subis
www.marque-nf.com
Black
Red
Antique Brown
Earth Brown
The firing process of the clay may produce slight differences in colour. To obtain a roof with a homogeneous appearance, we recommend mixing tiles from different pallets.
The printing processes do not necessarily guarantee a faithful reproduction of colours. Ask to see them in situ.
These values are given for information purpose only and are likely to change.
www.marque-nf.com
the main features
veRGEs
The wide range of Franche-Comte fittings
offers choice of two verge finishes:
• verge tile,
• standard verge, left and right.
Laying with gable tiles
Laying with standard verges
Gable tiles and tiles
Standard verges and tile
d=
1±1 16,5±1
6
d=
22,5±1 1±1
multiple of Lc
11,5
multiple of Lc
Standard verges, 1/2 tile and tile
Gable tile, 1/2 tile and tiles
Screw 50 Screw 70
Verges direction is determined
by placing them facing the pitch.
24
working height 6
d=
1±1 16,5±1
d=
22,5±1 1±1
multiple of Lc
7
25
9,3
44
25,5
5
working height 11,5
14,5
Dimensions in cm
lc = linear cover
15,5
multiple of Lc
14,5
44
13
44
26,5
25,5
43,7
18,2
18,2
16,3
8,5
Standard verge left
Verge tile right
Verge tile left
43,7
Standard verge right
Half tile
HIP / RIDGE
Monier recommends laying dry with ventilated
weather stripping in a roll.
Semi round ridge
tile 50
3-way apex
Ridge board
Ridge weather
stripping
This system enables the ridge and hip to adapt
to the nature movements of the roof.
Ridge board
support
Tile
Interlocking hip 40
Interlocking hip
starter 40
The ridge courses are made by cutting the tiles
closest to the ridge board.
The dry ridge/hip is quick to lay, provides good
ventilation, and makes future work easier.
30
20,8
27
54
24,2
20,8
48,5
46,5
working
height
small part 8,5
Semi round
ridge tile 50
overall height
small part 7,2
overall height
small part 8
39
overall
height
small part 7,2
Figaroll® plus
(28/32 cm)
4,5
± 0,5 cm
Dimensions in cm
All ridges and hips must be fastened with a clip.
22,5
24,2
Semi round
ridge tile 33
24,2
Interlocking
hip 40
Interlocking hip
starter 40
7,2
34,2
13
13
31,2
wakaflex® 18
(18 cm)
B Clip
for semi round
ridge tile 50
wakaflex® 28
(28 cm)
21
Verge pediment
with return
21
3 way apex
4 way apex
aeration, ventilation AND ILLUMINATION
Ø 22
The underside of the tiles and their support
must be ventilated. Ventilation guarantees good
long-term performance of roofing materials
making up the roof.
Type
of attic
The use of ventilation tiles is recommended
in the top and bottom sections of the roof.
Total
ventilation (1)
44
26,5
26,5
S = 1/5 000
Ø int. 16,5
Lantern
(Ø 150 mm)
The total cross sections of ventilation openings
should be distributed evenly (50-50) between
the lower section slopes and close to the ridge.
Humid or stagnant air coming from ventilation
or extracted from inhabited rooms
by mechanical or other ventilation
must be discharged outside the roof space.
Ventilation tile with grid
(opening 12 cm2)
S = 1/3 000
S = 1/5 000
1
S2 = 1/3 000 (2)
For further information on these two points,
please consult the DTU in force.
S1 = 1/5 000
S2 = 1/3 000 (2)
Flange tiles should be installed at the top
of the rake.
(1)
(2)
Related to the surface area
projected horizontally.
Except for Spirtech® type breathing
roof underlays.
44
44
26,5
Through tile
(Ø 150 mm)
26,5
Glass tile
Note :
for better performance, the through tiles must be laid
as much as possible near ridges.
These values are given for information purpose only and are
likely to change.
THE REGULATIONS
Valley and EaveS
Minimum pitch table in %
D
F
the main features
L
Zone I
Zone II
Zone III
The dimension DE mentionned by Monier is given as an example.
This dimension will vary according to several parameters : cant height,
gauge, roof pitch and overhang d, and may be adjusted to achieve the
required overlap. The interlocking part (water flow) must to be taken
into account when defining dimensions DE and d.
35
50
70
50
60
80
Minimum acceptable pitches in % (with underlay)
Zones Zone I
Zone II
Zone III
Sites
Sheltered30
Normal35
Exposed50
30
45
60
45
50
70
These data are applicable to slopes whose horizontal projection does not exceed 12 m.
Recommandations of DTU.
Zones for the application of minimum pitches
France is divided up into 3 zones for the application of minimum pitches
(with regard to wind/rain concomitance)
Note : if in doubt as to the zone of application, it is essentiall to refer
to the definition of the zones given below.
Profilo valley
Ventilated eaves batten
without comb
UNDER-ROOF
ZONE I
All inland areas and the
Mediterranean coastline for
altitudes of less than 200 m.
ZONE II
SPIRTECH® 100
SPIRTECH® 200
SPIRTECH® 300 SPIRTECH®+ 200 SPIRTECH®+ 300
- Atlantic coastline up to 20 km
inland, from Lorient to
the Spanish border.
- Strip between 20 to 40 km
from the coast, from Lorient
to the Belgian border.
- Altitudes between 200 m
and 500 m
SPIRTECH®
CLIMA + 200
ZONE III
SPIRTECH® BBC
200
SPIRTECH® BBC
300
CLIMA COMFORT
RENO®
SPAN-FLEX®
200
SPAN-FLEX®
300
- Atlantic, Channel and
North Sea coastline and inland
to 20 km, from Lorient
to the Belgian border.
- Altitudes above 500 m and
below 900 m.
SPAN-ALU
300
Laying tiles in a square layout
For violent winds, Monier recommends going beyond the DTU
recommendation and therefore fastening all tiles.
Definition of sites according to the DTU
(1) The wind zones concerned are those provided
for in rule NV 65 and sites by the reference DTU.
(2) One tile fastened every five tiles laid. Map reference NV65
SITES
On verges and eaves, all tiles must be fastened.
Use of Europanneton® FCR Inox recommended by Monier.
Pitches in %
p ≤ 100
100 < p ≤ 175
p > 175
Zones 1 and 2(1)
Zones 1 and 2(1) : Exposed site(1)
Protected and normal sites(1)
Zones 3 and 4 : All sites
Verges RunningVerges Running
and eaves
portion
and eaves
portion
all
free
all
1/5(2)
all
1/5(2)all 1/5(2)
all
all
all
all
49
18
Pinecone finial
(available in 44,5 cm)
24,5
Ornamental clay
cockerel
Normal Plain or plateau with slight vertical intervals, whether extensive or not (valleys, undulations).
Exposed Near the sea: inland to a distance of 5 km; the tops of cliffs, islands or narrow peninsulas,
estuaries or sheltered bays and ria. Inland: narrow valleys into which the wind is channelled,
isolated and high mountains (for example: Mont-Aigoual and Mont-Ventoux) and certain
mountain passes.
This breakdown into three zones should not be confused with the breakdown
into Snow and Wind regions given in the NV (Snow and Wind) rules.
To prevent ingress of powder snow, the DTU recommends the use of
an underlay.
This use is also advocated by SNEST in order to catch and lead down
to the gutter any small amounts of water as well as to protect against
the ingress of dust or soot.
ornAments
37
DEFINITION
Scheltered Low ground, entirely surrounded by hills which protect it against all wind directions. Site partially
bounded by hills in the direction of the most violent winds that provide protection against winds
in this direction only.
57,5
18
Fleur de Lys
finial
Monier reserves the right to change the technical characteristics of its range.
Fabienne Alexandre - Export Manager - 67, Avenue de Fontainebleau - 94270 Le Kremlin-Bicêtre - France
T : 00 33 1 58 91 20 98 - F : 00 33 1 58 91 21 42 - E : [email protected]
Nathalie Bernard - Trade Export Assistant - B.P. 4 - 16270 Roumazières - France
T : 00 33 1 41 86 13 88 - F : 00 33 5 45 71 88 93 - E : [email protected]
Head office: 67, Avenue de Fontainebleau - 94270 Le Kremlin-Bicêtre
T : 01 58 91 20 00 - F : 01 58 91 20 01
www.monier.fr
This documentation, which was 04/2012, supersedes all previous issues; it is a non-contractual document that may be revised at any time. Production: DTP: Centaure - Photos: P. Zandvliet - 3D drawings: Buster Studio - X - Centaure
LR = Rake length
DF = Ridge batten distance = 4,5 ± 0,5 cm
DL = Battening distance
DE = Eaves batten distance = 35 cm
To adjust for the desired overhang.
d = Eaves overhang = 8 cm
Sheltered35
Normal40
Exposed60
1503
d
PEFC/10-31-
E
Sites
D
Monier proposes a range of
preformed valleys.
Laying of a ventilated eaves batten
(ventilation 200 cm2/ml) on the tilt
batten guarantees linear ventilation
in the lower section in accordance
with the DTU’s recommendations.
Zones • Europanneton FCR Inox
for the eaves.
®
PROMOUVOIR
LA GESTION DURABLE
DE L A FORÊ T
LR
Minimum acceptable pitches in % (no underlay)
D
All tiles on the eaves must
be fastened.
Please refer to the DTU in force :