Elecdan EPS-8XM Quick Start Guide 2010 05
Transcription
Elecdan EPS-8XM Quick Start Guide 2010 05
ePowerSwitch ePowerSwitch 8XM Quick Start Guide Detailed information can be found in the User Guide on the provided CD-ROM 3. Controlling the power outlets over IP By using the administrator account (default name and password = admin) you will be able to do all settings and to control all power outlets. By using one of the 255 user accounts you will only be able to control the power outlets for which one the users has the rights. © Copyright All rights reserved ELECDAN • 2 impasse de la noisette • 91374 VERRIERES-LE-BUISSON • FRANCE Tél. +33 (0) 1 60 11 44 44 • Fax +33 (0) 1 69 20 39 63 • www.elecdan.com • [email protected] ePowerSwitch After configuring the network parameters using one of the previous methods, start your browser and enter the address of your ePowerSwitch. ePowerSwitch 8XM Master is an enhanced power distribution and control unit that enables remote power management of 8 devices (extendable up to 136) over the Internet and Intranet. This high security device supports the HTTPS protocol and also includes IP device and environmental monitoring functionalities. It supports the HTTP, HTTPS, DHCP, Syslog, SNMP, SMTP and SNTP protocols. An internal clock allows to timestamp syslog messages, e-mails and internal logs. Before operating your ePowerSwitch, please read the safety instructions in the User Guide on the provided CD-ROM. 1. Installation Connect the ePowerSwitch-8XM to your Local Area Network. Power-up the ePowerSwitch through properly grounded outlets. May 2010 ePowerSwitch 8XM 2. Configuration Use one of the three following methods: Configuration through the LAN using the Finder program contained on the CD-ROM It is the simplest and fastest configuration method if you use Windows as operating system and allows to configure your ePowerSwitch-8XM through your local network even if its network parameters are not compatible with those of your PC. 1. Start the ElecFinder.exe program. 2. In the tool bar, click on the first left button to discover the ePowerSwitch connected on your LAN. 3. In the tool bar click on the second left button and configure the network parameters. Configuration through the LAN using a standard Browser During the first installation, change temporarily the network settings of your PC according to the default network settings of the ePowerSwitch. Factory network settings of the ePowerSwitch-8XM IP Address: 192.168.100.200 - Port: 80 Gateway: 255.255.255.0 Default factory protocol is HTTP !!! 1. Start your Web browser and type following IP address: http://192.168.100.200/sysadmin.htm 2. Enter the administrator name and password (default for both = admin) The home page appears, allowing you to configure the settings of your ePowerSwitch 8XM. Configuration through an RS232 Terminal connection 1. Use the provided RS232 cable to connect the ePowerSwitch to an available serial port of your PC. 2. Run a Terminal program such as Windows HyperTerminal. 3. Configure the appropriate serial port @ 9.600, n, 8, 1 and no flow control. 4. On your computer, press <ENTER> until the network settings appears on your screen. 5. Press the M key on your keyboard and follow the menu to configure your ePowerSwitch-8XM. NETWORK INTERFACE PARAMETERS: Should this target obtain IP settings from the network?[N] Static IP address [192.168.1.250]? Subnet Mask IP address [255.255.255.0]? Gateway address IP address [192.168.1.2]? Primary DNS Server address IP address [192.168.1.2]? Secondary DNS Server address IP address [0.0.0.0]? MISCELLANEOUS: Finder program enabled?[Y] ePowerSwitch ePowerSwitch 8XM Guide d'installation rapide Des informations détaillées se trouvent dans le User Guide sur le CD-ROM fourni 3. Commandes des prises via Ethernet Le compte administrateur (nom et mot de passe par défaut = admin) vous permet de commander toutes les prises secteur. Les 255 comptes utilisateur permettent de commander uniquement les prises secteur pour lesquelles l’utilisateur dispose des droits d'accès. © Copyright Document non contractuel ELECDAN • 2 impasse de la noisette • 91374 VERRIERES-LE-BUISSON • FRANCE Tél. +33 (0) 1 60 11 44 44 • Fax +33 (0) 1 69 20 39 63 • www.elecdan.com • [email protected] ePowerSwitch Après avoir configuré les paramètres réseau, démarrez votre navigateur et saisissez l’adresse IP de votre ePowerSwitch. ePowerSwitch 8XM Master est une solution haute performance de gestion d'alimentation qui permet de commander à distance 8 prises secteurs (extensibles à 136) au travers d’un réseau Intranet ou Internet. L'interface Web supporte le protocole HTTPS pour garantir le plus haut niveau de sécurité possible. Cet équipement offre de nombreuses fonctions de surveillance d'équipements IP ainsi que de l'environnement (température, humidité, fumée…). Il supporte les protocoles HTTP, HTTPS, DHCP, Syslog, SNMP, SNTP et SMTP. Une horloge interne permet une gestion précise des actions programmées et la datation des messages Syslog, des e-mails et des évènements. Avant d’utiliser votre ePowerSwitch, lisez attentivement les consignes de sécurité indiquées dans le User Guide contenu sur le CD-ROM. 1. Installation Connectez l'ePowerSwitch-8XM à votre réseau local. Mettez-le sous tension en utilisant des prises secteur avec terre. Mai 2010 ePowerSwitch 8XM 2. Configuration Utilisez l’une des trois méthodes suivantes pour configurer votre ePowerSwitch-8XM : Configuration via le réseau local en utilisant le programme Finder contenu sur le CD-ROM. C’est la méthode la plus simple et la plus rapide si vous utilisez Windows. Elle permet de configurer votre ePowerSwitch-8XM au travers de votre réseau local même si ses paramètres réseau ne sont pas compatibles avec ceux de votre PC. 1. Démarrez le programme ElecFinder.exe. 2. Dans la barre d’outils, cliquez sur le premier bouton pour parcourir votre réseau local et rechercher l’ePowerSwitch que vous venez de connecter. 3. Dans la barre d’outils, cliquez sur le deuxième bouton et configurez les paramètres réseau. Configuration via le réseau local en utilisant un navigateur standard Lors de la toute première installation, modifiez momentanément les paramètres réseau de votre PC en fonction des paramètres réseau par défaut de l’ePowerSwitch-8XM. Paramètres réseau par défaut : Adresse IP : 192.168.100.200 – Port : 80 Passerelle : 255.255.255.0 Par défaut, le protocole usine est HTTP !!! 1.Démarrez votre navigateur et saisissez l’adresse IP : http://192.168.100.200/sysadmin.htm 2.Saisissez le nom et le mot de passe administrateur (admin par défaut pour les deux). La page d’accueil apparaît et vous permet de configurer votre ePowerSwitch 8XM. Configuration via l’interface série RS232 et une connexion Terminal. 1. Utilisez le cordon série fourni pour relier l’ePowerSwitch-8XM à un port série de votre PC. 2. Démarrez un programme Terminal comme Windows Hyper Terminal. 3. Configurez le port série de votre PC à 9.600, n, 8, 1, sans contrôle de flux. 4. Sur le clavier de votre PC, appuyez sur <ENTER> jusqu’à ce que les paramètres de configuration apparaissent. 5. Appuyez maintenant sur la touche M et suivez les instructions affichées à l’écran pour configurer votre ePowerSwitch-8XM. NETWORK INTERFACE PARAMETERS: Should this target obtain IP settings from the network?[N] Static IP address [192.168.1.250]? Subnet Mask IP address [255.255.255.0]? Gateway address IP address [192.168.1.2]? Primary DNS Server address IP address [192.168.1.2]? Secondary DNS Server address IP address [0.0.0.0]? MISCELLANEOUS: Finder program enabled?[Y]