C:\Documents and Settings\Chantal\Desktop
Transcription
C:\Documents and Settings\Chantal\Desktop
A G G G G G G G Figure #1 G G Figure #2 G E Step 1 : Unscrew the six 2 83'' Allenhead bolts with washers (G) from one of the stationary sides (B) of your crib using the Allen wrench (Z) that was provided with your crib hardware bag (see Figure 1). Remove it and store for future crib use. Keep four of the Allenhead bolts with lock washers for Step 2. Step 2 : Thread each of the four Allenhead bolt and lock washer (G) through the holes of the gate (E). Step 3 : Now place the toddler gate (E) (with the attached bolts) on the front of the crib and align with the existing holes in the right and left headboards (A). The toddler gate should be resting on the curved portion of the headboards (A). Step 4 : Before using the toddler bed retighten all bolts on the unit. NB : Tighten all the screws periodically, or if you move the unit to another location, or if you re-assemble the unit. Verify the integrity of the slats on the top and bottom of each one in order to detect potential weakening or other anomalies. Clean the unit with water and a soft cloth. Do not use chemicals. The minimum age of the user of the toddler bed shall not be less than 15 months and the maximum weight shall not be greater than 50 lb (22.7 kg). The mattress intended for use on the toddler bed shall be a full-size crib mattress having minimum dimensions of 51 5/8 in. in length and 27 1/4 in. in width and a minimum thickness of 4 in., but not exceeding 6 in. -G- (pre-assembled on crib) Qty. 4 -Z- (with crib hardware) Qty. 1 -E- Qty. 1 (METRIC) 2 3/8'' Allenhead Bolt with lock washer Allen Wrench TULIP is a division of Natart Juvenile, Inc. T (819) 364-3189 F (819) 364 - 2052 240 rue Pratte Gate Princeville, QC G6L 4T8 [email protected] Canada www.tulipjuvenile.com A G G G G G G G Figure #1 G G Figure #2 G E Étape 1. : Dévissez un de côtés fixes (B) sur votre bassinette à l'aide de la clé Allen (Z) qui était fournis dans votre quincaillerie de votre bassinette. Gardez 4 des 6 vis pour l'Étape 2. (Voir Figure 1) Étape 2. : Insérez chaques vis Allen et rondelle de blocage (G) dans les trous de la garde (E). (Voir Figure 2) Étape 3. : Maintenant, placez la garde (avec les 4 vis jointes) sur la partie courbée du devant de la bassinette et alignez avec les trous des Têtes gauche et droite (A). Étape 4. : Avant d'utiliser le petit lit, resserrez tous les vis. NB : Serrez toutes les vis régulièrement, ou si vous déplacez ou ré assemblez le petit lit dans un autre endroit. Vérifiez l'intégrité des barreaux sur le haut et le bas de chacun afin de détecter d'éventuels affaiblissement ou d'autres anomalies. Nettoyer avec eau et linge humide, ne pas utiliser des produits chimiques. L'âge minimum de l'utilisateur du petit lit ne doit pas être inférieure à 15 mois et le poids maximum ne doit pas être supérieure à 50 lb (22,7 kg). L'épaisseur du matelas utilisé dans le petit lit ne doit pas être supérieur à 15 cm et ses dimensions doivent être minimum de 131 cm de long et 69 cm de large. -G- Qté. 4 (pré-assemblé sur la bassinette) -Z- Qté. 1 -E- Qté. 1 (METRIC) Vis Allen 2 3/8'' avec rondelle de blocage (dans le sac de quincaillerie de la bassinette) TULIP is a division of Natart Juvenile, Inc. T (819) 364-3189 F (819) 364 - 2052 Clé Allen 240 rue Pratte Garde Princeville, QC G6L 4T8 [email protected] Canada www.tulipjuvenile.com