Tech Sheet - Soundtube
Transcription
Tech Sheet - Soundtube
CM31-EZ In-Ceiling Speaker Technical Information for System Engineers Key Features Specifications: CM31-EZ System Type Impedance (nominal) 1 Sensitivity dB @ 2.83 V/1 m Sensitivity dB @ 1 W/1 m 2 Frequency Response (- 3 dB) 3 Frequency Response (-10 dB) 3 Max. Program Power 4 Max. Continuous Power RMS 5 Max. Power SPL @ 1 m 6 Coverage Angle (-6 dB @ 2 kHz) Coverage Angle (-6 dB @ 10 kHz) Coverage Angle (averaged from 2 to 10 kHz) Directivity Factor (Q) Directivity Index (DI) dB Tap Selector (transformer accessory only) Transducer - Full-Range Driver Low Frequency Voice Coil Enclosure Material Grille Inputs Colors Backcan Diameter Backcan Height Visible Height Visible Diameter Weight Shipping Weight Packaging Included Accessories Optional Accessories Regulatory - UL Regulatory - CE RoHS 1 Impedance listed per IEC 60268-5 with a minimum less than 80% the nominal impedance 2 1 W 1 m sensitivity determined using nominal impedance 3 Frequency response measured in half or full space as dictated by speaker mounting configuration 4 Max program power is 3 dB above max continuous power 5 6 Continuous power rating, EIA-426-B test Max output based on max continuous power Tile bridge included 3 inch full-range, in-ceiling (10 watt transformer for 25/70.7/100-volt or transformer bypass position) 8 ohm 85.0 dB 85.0 dB 218 Hz - 14 kHz 135 Hz - 22 kHz 40 W 20 W 98.0 dB 175° 45° 120° 4.5 (averaged 100Hz - 10kHz), 3.5 (2kHz) 5.3 (averaged 100Hz - 10kHz), 5.2 (2kHz) Six-position rotary switch or transformer bypass position 76.1 mm (3.0 in.) Polypropylene driver with butyl rubber surround 19.0 mm (0.75 in.) ABS baffle, steel backcan Corrosion-resistant, powder-coated aluminum Hardwire lead Black or white 139.7 mm (5.5 in.) 88.9 mm (3.5 in.) 15.2 mm (0.6 in.) 160.6 mm (6.3 in.) 1.4 kg (3.1 lbs.) 1.8 kg (4.0 lbs.) One per box Tile Bridge, conduit connector, paint mask and wire nuts Pre-construction bracket (AC-CM3-PCB), 10 inch powered subwoofer (SM1001p) UL 1480 (UEAY) and 2043 approved Approved Approved Transformer Taps 70.7 V Output 10 W 95.0 dB 100 V Output 10 W 95.0 dB 25 V Output 1.3 W 86.0 dB 5W 92.0 dB 5W 92.0 dB 0.7 W 83.5 dB 2.5 W 89.0 dB 2.5 W 89.0 dB 0.4 W 81.0 dB 1.3 W 86.0 dB 1.3 W 86.0 dB 0.2 W 78.0 dB 0.7 W 83.5 dB 0.1 W 75.0 dB © 2012 SoundTube Entertainment. All rights reserved. CM31-EZ REV 02.14.12 • One 3 inch (76.2 mm) full-range highextrusion, high-fidelity polypropylene driver with butyl rubber surround. • Weatherized components for indoor/outdoor applications. • Shallow 3.5 inch (88.9 mm) deep all-steel backcan with integrated driver and baffle configuration. • Ultra-compact design with a total visible footprint of less than 6.3 inch (160.6 mm) diameter. • Rapid installation, blind-mount, fixedwing mounting mechanism with constant tension design affixing to wall thicknesses ranging from 0.1 in. (2.5 mm) to 1.5 in. (38.1 mm). • Corrosion-resistant, powder-coated aluminum grille with snap fit attachment. • UL 1480 (UEAY) and 2043 approved. • High quality black or white paint finish. • Included accessories: Tile bridge. • Optional accessories: Pre-construction bracket (AC-CM3-PCB) and 10-inch powered subwoofer (SM1001p). Description The CM31-EZ is a premium full-range 3-inch in-ceiling speaker for applications requiring 8 ohm or distributed audio solutions. The CM31-EZ incorporates low profile grille with a total visible footprint of 6.3 inch diameter and an integrated backcan and driver design for ultra compact in-ceiling installations. The in-ceiling speaker includes a six-position tap switch with a transformer bypass position. A tile bridge and mounting hardware are included and feature a fast and secure constant tension SpeedWing™ mounting system. The CM31-EZ incorporates weatherized components for indoor/outdoor applications. Applications Engineered for rapid installation and low profile mounting for smaller venues, the CM31-EZ is ideal for retail, restaurants, conference rooms, educational facilities or any setting where full-range intelligibility, low profile design and in-ceiling installation ease are paramount. For additional bass response down to 41 Hz (- 10 dB), the SM1001p powered 10-inch subwoofer may be incorporated. CM31-EZ In-Ceiling Speaker Technical Information for System Engineers Patented SoundTube Technologies SoundTube Entertainment and the MSE Audio Group constantly develop new technologies which enhance audio product performance. SoundTube Entertainment innovations are protected by multiple U.S. and international patents, which explicitly cover SoundTube dome, enclosure and dispersion technologies. The MSE Audio Group actively defends its patents in order to protect SoundTube resellers and end-users. Technical Data and Specification Tools Technical Data SoundTube Entertainment strives to provide complete and effective technical information and data to dealers, engineers and designers. All data are available from SoundTube Entertainment or at www.soundtube.com. Technical data and downloads include: production unit shall be as follows: Useable frequency response shall extend from 135 Hz – 22 kHz (- 10 dB). Measured sensitivity (2.83 volt input, 1 meter) shall be at least 85.0 dB. The speaker shall have a nominal impedance of 8 ohms. The speaker shall be available for 25-, 70.7- and 100-volt modes and shall include a six-position tap switch with a transformer bypass position. Rated power capacity shall be at least 20 watts continuous (RMS) and conform to EIA426-B. Maximum continuous power output at 1 meter shall be 98.0 dB. Installation for the speaker shall be by two-screw, blind-mount, constant tension fixed-wing assembly and shall attach to ceiling thicknesses ranging from 2.5 mm (0.1 in.) to 38.1 mm (1.5 in.). A secondary attachment point has been included on the back of the unit. The fixed wing assembly shall be constructed of steel. The external wiring shall be by hardwire lead and the speaker shall include a UL-listed conduit connector. Autodesk® Revit® software The maximum backcan dimensions shall be no more than 139.7 mm (5.5 in.) in diameter by 88.9 mm (3.5 in.) in height. The maximum visible dimension shall be no more than 15.2 mm (0.6 in.) in height by 160.6 mm (6.3 in.) in diameter. Tech Sheets – Technical information and architectural specs for system engineers The system shall be for indoor/outdoor applications. SoundTubeSPEC™ – Proprietary speaker placement software The enclosure shall be constructed of steel. The grille shall be constructed of powder-coated aluminum for lasting performance and affix to the speaker baffle via snap fit. EASE™ data – 3-D polar plots. EASE™ Address – 2-D modeling for distributed systems Acquisition & Verification All data for SoundTube speakers are independently collected from and verified by NWAA Labs (www.nwaalabs. com) using their proprietary MACH testing system. All data are collected and analyzed according to ASTM, ISO and AES standards using EASERA, TEF and MLSSA. Full balloon data including both phase and magnitude is compiled into a variety of formats including EASE 4.x, GLL and CLF. Architectural Specifications The loudspeaker transducer shall consist of one full-range 76.2 mm (3.0 in.) polypropylene cone with butyl rubber surround. The low-frequency voice coil diameter shall be 19.0 mm (0.75 in.). Performance specifications for a typical The system shall be the CM31-EZ for low- or high-impedance applications. SoundTube Entertainment 6430 North Business Park Loop Park City, Utah 84098 Phone 435.647.9555 Fax 435.647.9666 Toll Free 800.647.TUBE www.soundtube.com All SoundTube products come with a 5-year limited warranty. CM31-EZ In-Ceiling Speaker Technical Information for System Engineers Graphs and Plots Phase/Impedance Response Frequency Response 110 Frequency Response Horizontal Beamwidth (- 6dB) 180 100 150 90 80 120 Degrees dBSPL 70 60 50 40 90 60 30 30 10000 20000 10000 20000 5000 2000 Directivity Index (DI) Vertical Beamwidth (- 6dB) 20 150 15 120 10 dB 90 60 Directivity Index (DI) 5 0 -3dB -6dB -9dB 30 -5 0 Hertz 5000 2000 1000 500 200 100 50 20 20000 5000 2000 10000 Hertz 1000 500 200 100 50 -10 20 Degrees 1000 Hertz Vertical Beamwidth (-6 dB) 180 500 20 20000 10000 5000 2000 1000 500 200 100 50 20 Hertz 50 0 0 200 -3dB -6dB -9dB 10 100 20 CM31-EZ In-Ceiling Speaker Technical Information for System Engineers Horizontal Vertical Polar Plots 125Hz 1/3 Oct 125 Hz 330 300 250Hz 1/3 Oct 250 Hz Horiz Polar Vert Polar 0 0 330 30 -12 -12 -12 -12 300 60 300 60 -18 240 120 210 210 150 210 150 4,000 Hz Horiz Polar Vert Polar 0 0 330 30 240 120 210 150 8,000 Hz Horiz Polar Vert Polar 30 10,000 Hz Horiz Polar Vert Polar 0 0 150 180 8KHz 1/3 Oct 330 90 -36 180 4KHz 1/3 Oct 0 0 270 120 180 2KHz 1/3 Oct 90 240 120 180 -30 -36 270 90 60 -24 -30 -36 30 -18 -24 -30 270 90 300 60 -18 -24 240 10KHz 1/3 Oct Horiz Polar Vert Polar 0 0 330 30 -6 -6 -6 -6 -12 -12 -12 -12 300 60 -18 60 -18 300 90 -36 240 120 210 240 120 210 150 90 90 240 150 210 -36 270 120 90 240 120 210 150 180 180 -30 -36 270 60 -18 -30 -36 270 30 -24 -24 -30 -30 300 60 -18 -24 -24 270 0 0 -6 -36 300 330 30 Horiz Polar Vert Polar -6 -30 330 1KHz 1/3 Oct -6 -24 2,000 Hz 0 0 330 30 1,000 Hz Horiz Polar Vert Polar -6 -18 270 0 0 500Hz 1/3 Oct 500 Hz Horiz Polar Vert Polar 150 180 180 Technical data, EASE™ plots, SoundTubeSPEC™ software and product downloads available at www.soundtube.com Minimum/Maximum Ceiling Mechanical Drawings Side Thickness Top 89.4 mm (3.5 in) 105.7 mm (4.2 in) 139.1 mm (5.5 in) Min. 2.5 mm (0.1 in) ø 171.3 mm (6.7 in) 160.6 mm (6.3 in) Max. 38.1 mm (1.5 in) Included Accessories 16.3 mm (0.64 in) 16.3 mm (0.6 in) Optional Accessories 600.0 mm (23.62 in) 143.8 mm (5.66 in) 141.2 mm (5.56 in) 635.0 mm (25.00 in) 215.9 mm (8.50 in) 635.0 mm (25.00 in) 8.38 mm (0.33 in) Pre-Construction Bracket (AC-CM3-PCB) 211.1 mm (8.31 in) Tile Bridge SoundTube Entertainment manufactures a complete line of speakers for: Open-Ceiling • In-Ceiling • Surface-Mount • Outdoor • Sound-Focusing All SoundTube products are designed and engineered in the USA.