05-2845-21-21U - Leds-C4
Transcription
05-2845-21-21U - Leds-C4
BOOK 05-2845-21-21U IN TECHNICAL CHARACTERISTICS The photograph may not match the reference exactly. Please read the product description to identify the finish. Type: Wall fixture IP Protection degrees: IP20 Location: DRY Light source 1: 1 x LED Cree 3W Warm White - 3000K 182 lm(N) CRI 80 Angle of the optics / Reflector: 60º Voltage / Frequency: 120V/60Hz Warranty (Years): 2 Option to extend the guarantee (Years): 5 Units per box: 6 Pes net (lb): 0.97 MATERIALS / FINISHES Structure material: Steel Aluminium Structure finish: Chrome GEAR Gear included: Yes, electronic Download photometric file .ldt /.ies Lm(N): Nominal flow of light in actual working conditions. Its actual flow will depend on the environmental conditions and the efficiency of the optics and/or diffuser. LEDS-C4 reserves the right to make the necessary technical changes they deem adequate, in order to improve the features of the product. Please consult the sales team to clarify any doubt. (+34) 973 468 100 [email protected] www.leds-c4.com Luminaire Code 05-2845-21-21 Name Aplique BOOK 1x3W led prisma Line IESNA-2002 Measurem. Code 05-2845-21-21 Name Aplique BOOK 1x3W led prisma Date 28-07-2010 Lamp Code Number Position Efficiency 100.00% Coordinate system CG Total Flux Maximum value 157.50 cd Position C=0.00 G=0.00 Double Symmetrical 20 mm 20 mm Height Height LAMP 05-2845-21-21 1 62.70 lm Round Luminaire Round Luminous Area Diam. Diam. Horizontal Luminous Area Emitting area on Plane 0° Emitting area on Plane 90° 0.000314 m2 0.000020 m2 0.000020 m2 Emitting area on Plane 180° Emitting area on Plane 270° Glare area at 76° 0.000020 m2 0.000020 m2 0.000095 m2 Symmetry Type Measurement Distance Double Symmetrical 0.00 Maximum Gamma Angle Measurement Flux 90 62.70 lm Operator Temperature Humidity Notes 25.00 °C 60.00 % Source voltage Source current Photocell Line IESNA-2002 C.I.E. F UTE Code LAMP 05-2845-21-21 1 mm 1 mm Luminaire Lamps Name LAMP 05-2845-21-21 - 3.00 W 90 97 100 100 100 1.00 A D DIN 5040 B NBN Flux [lm] 62.70 Pow. [W] Q.ty 3.00 1 A60 BZ 1 Diam=20mm 90 Gamma Angles 180° 120° 0 40 105° 105° 180 270 90° 90° C Halfplanes 180.0 0.0 270.0 90.0 40 75° 75° 80 60° 60° 120 ULOR 0.00 % DLOR 100.00 % RN 45° 45° 160 0.00 % cd 200 30° LITESTAR (c)OxyTech Srl www.oxytech.it 15° 0° 15° 30° Page 1 LEDS, C4 S.A. CIF/VAT: A-59.410.910 C/ Afueras s/n -TORA- 25750 (LLEIDA) SPAIN TEL: 34 (73) 46 81 02 FAX: 34 (73) 46 81 06 SHEET: 1/1 EDITION: 01 REF: 05-2845U FIGURE Nº 1. UNPACK THE FIXTURE: CHECK THE CONTENTS OF THE BOX. YOU SHOULD RECEIVE: FIGURE Nº 1. DÉBALLER LE PLAFONIER: VÉRIFIER LE CONTENU DU CARTON, VOUS DEVEZ RECEVOIR: X2 X2 INSTALLATION INSTRUCTIONS FOR HANGING FIXTURES FIGURE 3, 4 AND 5 MOUNTING HARDWARE. NOTE: TEST THE CONNECTOR BY GENTLY PULLING IT. IF IT PULLS OUT THE CONNECTION, TRY AGAIN TILL YOU HAVE A FIRM CONNECTION. MAKE SURE NO BARE STRANDS OF WIRE STICK OUT FROM UNDER THE CONNECTORS. WHITE OR MARKED WIRE FROM FIXTURE WHITE WIRE FROM OUTLET BOX FIGURE 3 BLACK OR UNMARKED WIRE BLACK FIGURE 4 FIGURE 5 INSTRUCTIONS D'INSTALLATION POUR PLAFONIERS FIGURE 3, 4 ET 5 MONTAGE DE L'ÉQUIPE. IMPORTANT: ESSAYER DE TIRER LE CÂBLE D'ALIMENTATION DOUCEMENT.S'IL SORT DE LA CONNECTION, IL FAUDRAIT ASSURER QUE LA CONNECTION SOIT FERME. S'ASSUSER QUE LES FILS DES CÂBLES NE SONT PAS À DÉCOUVERT DU CONNECTEUR. CÂBLE BLANC OU MARQUÉ DU PLAFONIER CÂBLE BLANC DE LA BOÎTE FIGURE 3 CÂBLE NOIRE OU NOU-MARQUÉ FIGURE 4 NOIRE FIGURE 5 CAUTION: ATTENTION: "Warning", "This product is to be installed by a qualified electrician only." "Suitable for dry locations only" "Attention", le raccordement électrique sera effectué par un téchnicien électricien qualifié" "Adéquat seulement en lieux secs." CAUTION: 1.- Wrong lighting installation can be dangerous for your safety. 2.- Before starting, disconnect the power by turning off the general switch of the electric installation. 3.- Install light bulbs (not provided) that must not exceed markings on the fixture. 4.- To change the bulbs, disconnect the power by turning off the general switch and wait for the bulbs cool down. INSTALLATION: 1.- Make electrical connections, carefully read the Electrical Connection section. 2.- Assemble lighting onto the outlet box as shown on fig. 6, & 7. ELECTRICAL CONNECTIONS: (See fig. 3,4 y 5) 1.- Connect the white wire from the fixture to the white wire of the electric installation. 2.- Connect the black wire from the fixture to the black wire of the electric installation. 3.- Connect the grounding conductor from the fixture to the grounding wire of the electric installation. 4.- Spread out the electrical wires so that the black ones are on one side of the outlet box and the white ones are on the other side, and carefully introduce them into the outlet box. ATTENTION: 1. Une mauvaise installation peut compromettre votre sécurité. 2. Déconnecter la tension du réseau d'alimentation avant de réaliser toute opération. 3. Installer les ampoules (non fournies), ne pas utiliser d'ampoules d'un autre type ou d'une puissance supérieure à celle indiquée sur l'étiquette de la lampe. 4. Pour changer les ampoules, déconnecter la tension du réseau d'alimention et laisser refroider les ampoules. INSTALLATION: 1. Connecter au réseau, lire attentivement la section de "Raccordements électriques" 2. Installer l'appareil à la boîte de distribution comme indiqué dans les dessins 6 et 7. RACCORDEMENTS ÉLECTRIQUES (dessins 3,4 et 5) 1. Connecter le câble blanc de l'appareil au câble blanc de l'installation électrique. 2. Connecter le câble noir de l'appareil au câble noir de l'installation électrique. 3. Connecter le câble conducteur de prise de terre au câble de prise de terre de l'installation électrique. 4. Distribuer les câbles pour que tout le câblage noir soit par dehors et le câblage blanc soit par dedans. Ajuster et immobiliser à la boîte sans coincer aucun câble.