Installation Instructions
Transcription
Installation Instructions
DZ13050.PDF 02/08/06 Dee Zee Running Board Installation Instructions Congratulations on your purchase of a quality Dee Zee product. Dee Zee is recognized as having the highest quality running boards and accessories on the market today. We have earned this reputation by offering our customers a product they can be proud to place on their vehicles. Dee Zee meets all the criteria of manufacturing a custom-fit product which guarantees it to be the easiest product to install. Note: Please take time to read all of the instructions before beginning this installation. Warning! Please check for wiring or other obstructions before drilling any holes into the vehicle. If it is necessary to drill any holes into the vehicle, Dee Zee recommends putting a sealant or rust inhibitor around all holes drilled into the body of the vehicle. Warning! It is the sole responsibility of the vehicle owner to check for tire clearance. Warning! It is unlawful and dangerous to ride on running boards or side box boards while the vehicle is in motion. Cleaning Instructions: To maintain the bright finish of your Dee Zee running boards, clean with a mild detergent. For our stainless steel products and accessories, the application of a high grade automotive type wax is recommended. If you should happen to have any questions with this product or you have an installation question, please feel free to call us at: 1-800-779-8222 If you would like to find out more information on Dee Zee’s products please feel free to visit our website at: WWW.DEEZEE.COM DZ13050.PDF 02/08/06 Dee Zee Guardian Running Board Installation Instruction DZ 13050 / DZ 13350 (2006 - Current) Chevy Tahoe A Side Box Board B X2 E Guardian Endcap - Insert I F M D Guardian Mudflap G J 1/4” Flat Washer Guardian Endcap N X4 X2 H 2 Left 2 Right K X8 O 1 1/4” x 3/8” Spacer X8 L 1/4” Hex Nut X8 1/4” U-Clip Front Plastic Trim Piece X2 1 Left 1 Right X8 1/4 x 1 ½“ Black Sheet Metal Screw C Rear Plastic Trim Piece 13 ft. 2 Left 2 Right 1/4 x 3/4” Slotted Hex Head Bolt Bulb Seal Gasket 1/4 x 1“ Black Sheet Metal Screw X14 #10x5/8” Phillips Head Screw X8 X8 Tools Required: Ratchet / Wrench Sizes: 13mm 7/16” 3/8” Tape Measure Drill Tin-snips 3/16” Drillbit 1/4” Drillbit Phillips Head Screwdriver 1 Place four 1/4 x 3/4” slotted hex head bolts (I) into the channel in the bottom of guardian running board (A) as shown below. A I I I I 2 Slide a rear plastic trim piece (C) and front plastic trim piece (D) into the channels in guardian running board (A) as shown below. A C L D If you are installing mudflaps on your guardian running board, then follow the steps shown below. If installing endcaps on your guardian running board (A), then proceed to the next page. Si vous installez des mudflaps sur votre panneau courant de gardien, alors suivez les étapes montrées ci-dessous. S'installant des endcaps sur votre panneau courant de gardien (a), procédez alors à la prochaine page. Mudflap Installation: Slide the guardian endcap (G) onto the end of guardian running board (A) and then place guardian mudflap (F) onto the guardian endcap (G). Secure them to the channels in guardian running board(A) using 1/4 x 1 ½” sheet metal screws (M). Tighten into place using a 3/8” wrench / or socket. A Front of Guardian Running Board G F M M 3/8“ Wrench or Socket Endcap Installation: Slide guardian endcaps (G) onto guardian running board (A) and attach using 1/4 x 1“ sheet metal screws (L). Tighten the 1/4 x 1“ sheet metal screws (L) into place using a 3/8“ wrench / socket. Now slide 1/4” U-Clips (N) onto guardian endcap inserts (E) as shown below. Glissez les endcaps de gardien (g) sur le conseil courant de gardien (a) et les attachez à l'aide des vis en métal de feuille de 1/4 x de 1"(l). Serrez les vis en métal de feuille de 1/4 x de 1" (l) dans l'endroit à l'aide d'une clé/d'douille de 3/8". Diapositive maintenant les U-Agrafes de 1/4"(n) sur les insertions d'endcap de gardien (e) comme montré ci-dessous. A E G N M E M N Slide guardian endcap inserts (E) onto guardian endcaps (G) and attach using #10 x 5/8” phillips head screws (O) and 1/4 x 1” sheet metal screws (L). Tighten the #10 x 5/8” phillips head screws (0) using a phillips head screwdriver and the 1/4 x 1” sheet metal screws (L) using a 3/8” wrench /or socket. Insertions d'endcap de gardien de glissière (e) sur les endcaps de gardien (g) et attache à l'aide des vis principales 5/8"Phillips de #10 X (o) et des vis en métal de feuille de 1/4 x de 1" (l). Serrez les vis principales 5/8"Phillips de #10 X (o) à l'aide d'un tournevis principal Phillips et les vis en métal de feuille de 1/4 x de 1" (l) à l'aide d'une douille de la clé /or de 3/8". E 3/8“ Wrench or Socket G O L Phillips Head Screwdriver L Place the bulb-seal gasket (B) onto the backlip of the guardian running board (A) and press it firmly into place. Cut the bulb-seal gasket (B) so that it is flush with the ends of guardian running board (A). Placez la garniture d'ampoule-joint (b) sur le backlip du panneau courant de gardien (a) et appuyez-la fermement dans l'endroit. Coupez la garniture d'ampoule-joint (b) de sorte qu'elle soit affleurante des extrémités du panneau courant de gardien (a). B Guardian Running Board Assembly with Endcaps B A Guardian Running Board Assembly with Mudflap and Endcap A B A B A 4 13mm Wrench or Socket Factory Running Board Locate the 2 existing mounting bolts Remove the 2 existing bolts per bracket on the existing factory board. Do not discard the bolts. 5 13mm Wrench or Socket Remove existing bolt at front of factory board. Replace existing bolt at front of vehicle. For reference, bracket shown with fasteners removed. 6 13mm Wrench or Socket Place 1/4” flat spacer (H) between vehicle and bracket, insert existing bolt through bracket and spacer. Finger-tighten bolts. Place the Running Board up to the body mount brackets. Align the (4) 1/4” x3/4” slotted hex head bolts(I) with the slots in the body mount brackets. 7 13mm Wrench or Socket Secure into place using 1/4” flat washer (J) and hex nuts (K). Hand-tighten. Make any final adjustments to the alignment of the running board on the vehicle. Tighten all bolts. 8 Using the pictures below as a guide, first drill three 3/16” holes through the mudflap on the running board and the sheet metal in the wheel well opening of the vehicle. Secure the mudlfap to the sheetmetal of the wheel well opening using 1/4 x 1" sheet metal screws (L) as shown in Step 10 of this instruction. Tighten until snug using a 3/8” wrench / or socket. Wheel Well Opening Drill with a 3/16” Drillbit L O L O L Mudflap on Guardian Running Board Drill with a 3/16” drillbit