ec type-examination certificate n°. 0162/18457/11

st
According to the EEC instructions 89/686 dated 21 of December 1989, concerning the standardization of legislation of
th
all member countries with regard to individual protection systems and the relative legislative decree dated 4 of
December 1992, N° 475,
A.N.C.I servizi s.r.l – C.I.M.A.C. section
CENTRO ITALIANO MATERIALI DI APPLICAZIONE CALZATURIERA
Authorized with the decree issued by the Ministry of Industry of the Italian Republic
On the 11th of October 2000 – Community identification N° 0465
grants:
EC TYPE-EXAMINATION CERTIFICATE
N°. 0162/18457/11
for the following model of personal protective equipment:
Protective glove – art. “9227 PAD ESD”
Manufacturer (see notes):
WUXI PAD SAFETY PRODUCTS CO., LTD.
WUXI, CHINA
On behalf of:
ANTIS GROUP SPA
VIA BETTOLE, 12
25010 BORGOSATOLLO BS
ITALIA
Vigevano, 23th December 2011
EC Type-Examination Certificate N°. 0162/18457/11
dated 23/12/11 – Page: 1 of 4
1. Description of personal protective equipment:
Category of PPE: second category
Protective glove against mechanical risk with specific protection on the palm
In compliance with EN 388 (03) standard
Size range: from 7 to 10
Manufacturing process: sewed and dipped
EC Type-Examination Certificate N°. 0162/18457/11
dated 23/12/11 – Page: 2 of 4
2. The tests and the examinations to verify the conformity of the article (in compliance
with art. 10 of Directive 89/686/EEC) are performed applying the following
harmonized standards and the Directive 1907/2006/CE - XVII:
Standard applied
A – EN 420 (10) – General requirement for gloves.
B – EN 388 (03) – Protective gloves against mechanical risk.
3. The results of tests and examinations are contained in the following test reports:
C.I.M.A.C.
RP 20114615
22th
dated
December 2011
4. Requirements of the personal protective equipment:
The model of protective glove article 9227 PAD ESD complies with:
-
The requirements of EN 420 (03) standard, points 4.1, 4.2, 4.4, 5 and 5.2;
-
The performance levels as specified in prospectus 1 of EN 388 (03) standard;
Performance levels
6.1
Abrasion resistance
4
6.2
Cut resistance
1
6.3
Tear resistance
4
6.4
Puncture resistance
2
-
the requirements of the EN 1149 (08) Part 5 in relation to the features of surface resistivity
-
The components of the glove complies with the requirements of Directive 1907/2006/CE XVII
EC Type-Examination Certificate N°. 0162/18457/11
dated 23/12/11 – Page: 3 of 4
5. Marking of the personal protective equipment
The following information is provided on the back of the glove:
- the “EC” mark
- the article code: 9227 PAD ESD
- the manufacturer trade mark: ANTIS GROUP
- the glove size
- the symbols concerning the protection provided:
protection against mechanical and antistatic properties
-
The performance levels as specified in prospectus 1 of EN 388 (03) standard;
Performance levels
6.1
Abrasion resistance
4
6.2
Cut resistance
1
6.3
Tear resistance
4
6.4
Puncture resistance
2
6. Notes:
-
-
-
The manufacturer is the one assuming the responsibility of design and fabrication of a product included in the
Directive, in order to throw it in the market.
This EC Type-Examination Certificate must be kept by the manufacturer, in order to produce it, on request, for
the control body of safety control administration.
The content of this EC Type-Examination Certificate is referred to the tested personal protective equipment
only.
This EC Type-Examination Certificate may be integrally duplicated; the copy must be faithfull, legible (if pint
size) and must contain the bold caption “TRUE COPY”.
The manufacturer should inform CIMAC for any modification to the product, to the place/process of
manufacturing and, if relevant (III category PPE), to the quality system if this compromises the conformity of the
product to the essential requirements or other provisions of the Directive 89/686/EEC.
The manufacturer should report all the complaints relating to the conformity of the certified products to the
requirements of the reference harmonized standards and supply these reports on request of A.N.C.I. Servizi
S.r.l. sez. CIMAC.
The manufacturer should implement appropriate corrective actions when non conforming products to the
requirements of the EC certification are identified.
EC Type-Examination Certificate N°. 0162/18457/11
dated 23/12/11 – Page: 4 of 4