Data Sheet TP75 Heating Controller Programmable Room
Transcription
Data Sheet TP75 Heating Controller Programmable Room
Data Sheet TP75 Heating Controller Programmable Room Thermostats Application & Features Typical System Connections The TP75 is a true seven-day programmable thermostat incorporating many useful features. An optional Optimum Start function will enable a required comfort temperature to be achieved by a programmed time, without wasting fuel because the heating plant started earlier than necessary. The chrono-proportional control logic ensures optimum comfort with minimal fuel consumption. The basic model incorporates a temperature sensor within the casing, but a remote sensor version is also available. Both can be converted to operate as an electronic thermostat, controlling at a constant, user selected, temperature. The Holiday Mode uses this temperature for a selected number of days, before automatically returning to programmable thermostat mode. Versions are available for use with a third- party telephone line switching device so that frost mode or holiday mode can be cancelled whilst away from home. ● Battery powered, programme unaffected by mains power failures ● Volt-free output contacts, rated 10 to 250Vac, 50/60Hz, or dc 10mA to 2(1)Amp. ● Integral or remote temperature sensing ● Up to 6 programmable temperature changes per day, including a programmable "OFF" function ● Selectable 7 day or 5/2 day programme ● Selectable time or temperature display ● Temperature range, 5°C to 30°C, in increments of 0.5°C. ● Selectable Chrono-proportional control or On/Off control ● Optional Optimum Start ● Frost protection function ● Thermostat function for constant temperature setting ● Holiday function, up to 99 days at a constant, selectable temperature ● Extend override, maintains existing set temperature for a further 1, 2 or 3 hours ● Selectable All Day programme, 1st event temperature lasts until 6th event becomes active ● Remote reset of Frost or Holiday functions possible Direct Burner Control Zone control with motor open/ motor close two port valve Wallplate teminals Live Input Heating On Off Heating On Off A B C 1 2 3 4 5 6 A B C 1 2 3 4 5 6 N E 3 amp fuse Live Input Wallplate teminals EARTHS NOT SHOWN. ENSURE EARTH CONTINUITY THROUGHOUT N E 3 amp fuse N N L N E Mains N L N E Mains 1 Data Sheet TP75 Heating Controller Specifications Integral temperature sensor Feature 3* or 6 cycles per hour, chrono-proportional control 12* or 6 cycles per hour, chrono-proportional control Programmes User overrides Factory pre-set programme, all may be changed Note: An "OFF" event can also be programmed DIL switch options at the time of installation Voltage Rating Contact Current Rating Switching Action Main Batteries Memory Retention Max. Ambient Temperature Dimensions mm Fixing clearances, internal wiring & DIL switch settings Model Designations Remote Remote temperature teleswitch sensor reset TP75 TP75A TP75B TP75AB TP75C TP75AC TP75BC TP75ABC Profiled - (up to 6 temperature changes per day) All Day - ( 1st event temperature lasts until 6th event time) Raise or lower temperature setting Extend duration of existing temperature setting by 1, 2 or 3 hours Select Profiled or All Day programme Monday to Friday Event Saturday & Sunday 20°C at 06:30 1 20°C at 07:30 15°C at 08:30 2 20°C at 09:30 20°C at 11:30 3 20°C at 11:30 15°C at 13:30 4 20°C at 13:30 21°C at 16:30 5 21°C at 16:30 15°C at 22:30 6 15°C at 22:30 DIL Switch No. Factory Pre-set Installer Alternative 1 7 day programme 5/2 day programme Optimum Start Optimum Start 2 Control Disabled Control Enabled On/Off control Chrono control 3 enabled enabled 3 or 12 control cycles 6 control cycles 4 per hour (see above *) per hour 10-250Vac, 50/60Hz or 10-250Vdc 10mA to 2 Amp (res), 1 Amp (ind) SPDT voltage free 2 x AA alkaline dry cells (Duracell preferred) to be renewed every 24 months Sufficient to remove and replace batteries within one minute 45°C 135 wide x 88 high x 32 deep Internal wiring Terminals 30 mm minimum Factory pre-set DIL switch settings Outline of unit A B C Wall or plaster box mounting holes N&E looping terminals ELECTRONICS 5/2 day A B C 1 2 3 4 5 6 Clearance for screwdriver access Remote Control Functions External Connections * NOTE: Remote start-up connections vary with model. Remote temp sensor & teleswitch reset A B C Remote Sensor Knockouts for bottom cable entry 1 2 TP75A TP75AC 3 4 5 Live Input Aperture for rear cable entry 6 A B C Remote start-up circuit 1 2 3 * TP75B TP75BC 4 5 6 On Off Heating 7 day OSC ON OSC OFF CHRONO ON/OFF Chrono 6 Chrono 3 or 12 A B C Remote Sensor 1 2 Remote start-up circuit 3 4 5 6 * TP75AB TP75ABC Danfoss Randall can accept no responsibility for possible errors in catalogues, brochures and other printed material, and reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed. Danfoss Randall Limited Ampthill Road Bedford, MK42 9ER Tel: (01234) 364621 Fax: (01234) 219705 Email: [email protected] Website: www.danfoss-randall.co.uk 2 Part No. 320 Iss.7. 03/99