Build Specifications MTB Hubs
Transcription
Build Specifications MTB Hubs
Build Specifications MTB Hubs Important information about hub compatibility This document is intended to communicate hub dimensions necessary for building wheels with SRAM hubs. For more detailed information, please contact your SRAM Account Manager. Table of Contents X0 Front Hub with Side Swap™ Symmetrical End Caps ...................................................................................................................................................................................................4 X0 Rear Hub with Side Swap™ Symmetrical End Caps ..................................................................................................................................................................................................... 5 X9 - 20x110 front................................................................................................................................................................................................................................................................................. 6 X9 - 15x100 front................................................................................................................................................................................................................................................................................. 7 X9 - 12x142 rear.................................................................................................................................................................................................................................................................................... 8 X9 - 12x135 rear.................................................................................................................................................................................................................................................................................... 9 X7/X9 QR................................................................................................................................................................................................................................................................................................. 10 MTH 716/746............................................................................................................................................................................................................................................................................................ 11 MTH 406/506..........................................................................................................................................................................................................................................................................................12 MTH 306...................................................................................................................................................................................................................................................................................................13 MTH 300.................................................................................................................................................................................................................................................................................................. 14 wa r n i n g • Use only 10 mm length rotor bolts. Rotor bolts longer than 10 mm will not secure the rotor to the wheel hub. 10 mm X0 Front Hub with Side Swap™ Symmetrical End Caps E B 15 mm Thru Axle Quick Release A E B C D E B C 20 mm Thru Axle Quick Release with Torque Caps C D E B C D D Quick Release with Torque Caps are compatible with RockShox Quick Release forks only. hub specifications (in millimeters, unless otherwise specified) Spoke hole count 32 A B C D E (spoke hole diameter) (pitch circle diameter) (center to flange) (center to flange) (pitch circle diameter) 2.7 49 22 34 46.5 Do NOT use a radial lacing pattern as it may damage your hubs. Radial lacing will void your warranty. 4 Quick Release A E B 12 x 135 mm Thru Axle X0 Rear Hub with Side Swap™ Symmetrical End Caps E B C D 12 x 142 mm Thru Axle C D E B C D hub specifications (in millimeters, unless otherwise specified) Spoke hole count 32 A B C D E (spoke hole diameter) (pitch circle diameter) (center to flange) (center to flange) (pitch circle diameter) 2.7 50 34.25 20.5 57 These specificaions are also applicable to hubs with an XD driver body. Do NOT use a radial lacing pattern as it may damage your hubs. Radial lacing will void your warranty. 5 X9 - 20x110 front A.1 A.2 B E C D hub specifications (in millimeters, unless otherwise specified) Spoke hole count 32 A.1 A.2 (spoke hole diameter) 2.5 2.7 B C D E (pitch circle diameter) (center to flange) (center to flange) (pitch circle diameter) 58 22.65 31.85 45 Do NOT use a radial lacing pattern as it may damage your hubs. Radial lacing will void your warranty. 6 X9 - 15x100 front A B E C D hub specifications (in millimeters, unless otherwise specified) D Spoke hole count A (spoke hole diameter) B (pitch circle diameter) C (center to flange) (center to flange) E (pitch circle diameter) 32 2.5 58 22.4 32.4 58 Do NOT use a radial lacing pattern as it may damage your hubs. Radial lacing will void your warranty. 7 X9 - 12x142 rear A B E C D hub specifications (in millimeters, unless otherwise specified) Spoke hole count A (spoke hole diameter) B (pitch circle diameter) C (center to flange) D (center to flange) E (pitch circle diameter) 32 2.5 58 34.25 20.25 58 Do NOT use a radial lacing pattern as it may damage your hubs. Radial lacing will void your warranty. 8 X9 - 12x135 rear A B E C D Spoke hole count A (spoke hole diameter) B (pitch circle diameter) C (center to flange) D E (center to flange) (pitch circle diameter) 32 2.5 58 34.15 20.35 58 Do NOT use a radial lacing pattern as it may damage your hubs. Radial lacing will void your warranty. 9 X7/X9 QR A.2 A.1 A.2 REAR FRONT A.1 B E C B E D C D hub specifications (in millimeters, unless otherwise specified) Spoke hole count Front Rear 32 A.1 A.2 (spoke hole diameter) 2.5 2.7 B C D E (pitch circle diameter) (center to flange) (center to flange) (pitch circle diameter) 22.05 33.45 34.4 20.4 58 Do NOT use a radial lacing pattern as it may damage your hubs. Radial lacing will void your warranty. 10 45 MTH 716/746 A REAR FRONT A B E C B E D C D hub specifications (in millimeters, unless otherwise specified) Front Rear Spoke hole count A (spoke hole diameter) B (pitch circle diameter) 32 2.5 58 C (center to flange) D (center to flange) 22.3 32.3 34 20.4 Do NOT use a radial lacing pattern as it may damage your hubs. Radial lacing will void your warranty. 11 E (pitch circle diameter) 58 MTH 406/506 A.2 A.1 A.2 REAR FRONT A.1 B E C B E D C D hub specifications (in millimeters, unless otherwise specified) Spoke hole count Front Rear 32 A.1 A.2 (spoke hole diameter) 2.5 2.7 B C D E (pitch circle diameter) (center to flange) (center to flange) (pitch circle diameter) 21.9 32.9 34.4 20.4 58 Do NOT use a radial lacing pattern as it may damage your hubs. Radial lacing will void your warranty. 12 45 MTH 306 A REAR FRONT A B E C B E D C D hub specifications (in millimeters, unless otherwise specified) Front Rear Spoke hole count A (spoke hole diameter) B (pitch circle diameter) 32 2.5 58 C (center to flange) D (center to flange) E (pitch circle diameter) 21.8 33 58 34.4 20.4 58 Do NOT use a radial lacing pattern as it may damage your hubs. Radial lacing will void your warranty. 13 MTH 300 A REAR FRONT A B B E C E D C D hub specifications (in millimeters, unless otherwise specified) Front Rear Spoke hole count A (spoke hole diameter) 32 2.5 B (pitch circle diameter) C (center to flange) D (center to flange) E (pitch circle diameter) 38 34.5 34.5 38 45 33.7 20.1 45 Do NOT use a radial lacing pattern as it may damage your hubs. Radial lacing will void your warranty. 14 www.sram.com Copyright ©2013 SRAM, LLC Gen.0000000004375 Rev D