kandi stix so

KANDI STIX SO
I N S T A L L A T I O N
Verify electrical plan.
Rotate fixture to expose screw holes.
Make sure to use all four screw holes
when mounting.
1
2
Ensure Power is Off!
Junction Box
Not Included
3
10’ KANDI STIX Leader Cable
Optional: 0-10v wiring diagram
Optional Dimming With ON/OFF Control Wiring
Diagram Using Lutron NTFTV & PP-20 (By others):
Connect the NTFTV dimmer as shown below. Use only
Lutron PP-20 Power Packs for AC line switching. Do not
install the PP-20 in the same wallbox as the
Low - Voltage Ballast Control. Refer to the wiring sheet
included with the PP-20 for more information
Max run 110 fixtures at 120v, 300 fixtures at 277v
#110
#109
Optional 1’ Jumper Cable
End Cap
0-10v
Dimmer only
Lutron
Model:
NTFTV
Purple
Gray
100-277v If dimming
AC
wire to:
50/60Hz Lutron
PP-20
White
#1
Black
Black White Purple Gray
10’ KANDI STIX Leader Cable
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS
INVOLVED. CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE
PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.
All MODA LIGHT products should be installed by a Licensed Electrician to local & national code. Do not modify, adapt or cut any MODA LIGHT components, plugs or accessories. Any modifications will void the warranty
and may create a potential safety hazard. Do not put on the same circuit as inductive loads. Incorrect wiring will result in irreparable permanent damage to the LEDs and fixture. MODA LIGHT tests all products before
shipping, and will not replace items that have been destroyed by incorrect wiring or handling. Ensure electrical circuit is switched off before wiring. See MODA LIGHT terms and conditions for product limited warranty.
© Cop yrig ht 2 01 5 • 955 W hit e Dr iv e, Las Vega s , N V 8 9 11 9 • T: 7 0 2 4 0 7 7 7 7 5 • F : 7 0 2 4 0 7 7 7 7 3 • w w w.m o d a l i g h t.co m
KANDI STIX SO
I N S T A L L A T I O N
4
KANDI STIX
End Cap
Optional 1’
KANDI STIX
Jumper Cable
5
#1
100-277v AC 50/60Hz
#2
.....
Max Run Lengths: 110pcs at 120v, 300pcs at 277v
#109
#110
End Cap Must be Placed on Last Fixture
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS
INVOLVED. CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE
PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.
All MODA LIGHT products should be installed by a Licensed Electrician to local & national code. Do not modify, adapt or cut any MODA LIGHT components, plugs or accessories. Any modifications will void the warranty
and may create a potential safety hazard. Do not put on the same circuit as inductive loads. Incorrect wiring will result in irreparable permanent damage to the LEDs and fixture. MODA LIGHT tests all products before
shipping, and will not replace items that have been destroyed by incorrect wiring or handling. Ensure electrical circuit is switched off before wiring. See MODA LIGHT terms and conditions for product limited warranty.
© Cop yrig ht 2 01 5 • 955 W hit e Dr iv e, Las Vega s , N V 8 9 11 9 • T: 7 0 2 4 0 7 7 7 7 5 • F : 7 0 2 4 0 7 7 7 7 3 • w w w.m o d a l i g h t.co m