Fiche technique
Transcription
Fiche technique
Fiche technique SX Premium SX Self Adhesive Lead Flashing Rolls Self adhesive flashing lead colour When laying adjacent rolls, SX Lead Flashing should be overlapped by a minimum of 25mm for a perfect watertight seal. The seam should be pressed firmly, but carefully, with a hand roller. Pay particular attention at the point of overlap. It is the user’s responsibility to dispose of all packaging correctly. Spécifications techniques From +5°C to +45°C Temperature d'application Allongement à la rupture Description du produit EN 123-1 Long.>15% Trans.> 15% Restrictions • A self adhesive aluminium flashing tape coated with a thick layer of rubber-bitumen adhesive protected by a release paper, which is removed before application. For general protection of brick, concrete, metal etc. against weathering and corrosion. Do not apply to surfaces below +5°C. May become brittle in a cementitious mix. Contact with acidic and alkaline liquids should be avoided. Avoid using where it will come into contact with solvents and oils. Not suitable in conjunction with silicone sealan Conditionnement Avantages • • 10m x 100mm (packed 1 x 3) Waterproof and will stick to most surfaces. Stockage et conservation Applications An easy to use waterproof flashing tape which will stick to most surfaces. When pressed into place the adhesive backing forms a watertight seal. For repairs to guttering and downpipes, most types of roofing, replacement or repair of existing flashings, joints between brickwork and other materials, cracks in concrete. For sealing projections through roofs and skylights, valley guttering, roof ridges, chimney caps and waterproofing joints. Shelflife of 12 months after production date. Store between +5°C and +40°C in dry, covered premises. Sécurité La fiche des données de santé et de sécurité doit être lue et comprise avant l’utilisation. Elles sont disponibles sur demande et sur le site Den Braven. Garantie Mise en œuvre All surfaces must be smooth, clean, dry and dust free. Any loose matter must be removed with a wire brush. Porous or rough surfaces should be primed with a bitumen primer and allowed to dry before application. Cut a section of SX Lead Flashing to the required length, remove the release paper and press down the adhesive bitumen to the previously prepared surface. Smooth gently into position using hand pressure only. Using a roller or a piece of rounded wood smooth the tape to ensure good overall contact and expel any air, especially on overlaps and at edges. Den Braven garantie que son produit est conforme à sa spécification durant sa durée de conversation. Disclaimer Les informations dans ce document et aussi dans nos publications imprimées et digitales sont fondées sur nos connaissances et expériences actuelles. Den Braven n’est pas responsable des fautes, inexactitudes ou déficiences rédactionnelles qui sont le résultat de changements ou recherches technologiques entre la date de publication de ce document et la date de l’acquisition du produit. Den Braven se réserve le droit de changer des formulations. Avant d’appliquer le produit l’utilisateur doit se familiariser avec les informations présentées dans ce document et/ou dans tout autre document y afférent. Avant l’application du produit l’utilisateur doit effectuer les tests nécessaires pour assurer que le produit est adapté à l’application. La méthode d’application, les conditions lors du stockage et du transport échappent à notre contrôle et seront en conséquence pas de notre responsabilité. Une responsabilité pour cette fiche d’information produit ne peut pas être acceptée. Les livraisons se font uniquement à nos conditions de livraison et modalités de paiement. Les informations détaillées de la présente fiche technique sont données à titre indicatif et ne sont pas exhaustives. Den Braven France sarl. Z.I. Le Meux - Rue du buisson du roi - BP 20114 – FR 60881 LE MEUX CEDEX T +33 (0)3 44 91 68 68 | F +33 (0)3 44 91 68 92 | E [email protected] 2016-09-30 23:30:53 UTC