Installation Instructions
Transcription
Installation Instructions
Installation Instructions Aphos™ RW Luminaires This luminaire is designed for outdoor and indoor lighting applications, and should not be used in areas of limited ventilation, or in high ambient temperatures. WARNING Risk of electrical shock. Disconnect power before servicing or installing Luminaire. Risqué de choc électrique. Couper l’alimentation avant l’entretien. WARNING Risk of injury or damage. Luminaire will fall if not installed properly. Read and follow installation instructions before beginning. Risqué de blessure. Une installation inappropriée peut causer la chute de l'ensemble luminaire. Lisez les informations cidessous avec attention avant d’utiliser ce produit. CAUTION Risk of injury. Wear safety glasses, gloves, and any required PPE during installation and servicing. Risqué de blessure. Portez des lunettes de sécurité et des gants lors de l’installation. Tools Required: Installation is completed using ordinary tools including: Driver or wrench with SAE 1/2 inch hex socket Torque wrench capable of 240 in-lbs (27.1 N-m) Wire strippers suitable for 18 AWG and gauge of supply wire. 3/16 Flat screwdriver. Specifications: Weight: ~20.6 lbs (~9.4 kg) IP Rating: Optical IP65, Driver IP66 Luminaire UL Wet Location Listed EPA: 0.48 ft2 Rated Voltage / Frequency: 120 to 277 VAC / 50 to 60 Hz Rated Voltage / Frequency: 347/480 VAC / 50 to 60 Hz requires step-down autotransformer Unpacking: This Luminaire has been properly packed so that no damage occurs during transit. Inspect to confirm prior to installing. Installation: This Luminaire has been designed to mount to a 2 3/8” OD pipe This equipment is intended to be installed by qualified personnel. The installation must be made in accordance with the current edition of the National electric Code, and all applicable state and local building codes. The final installation must be approved by the appropriate, qualified, electrical/building inspector(s). Improper installation may result in a risk of fire or electrical shock hazard. The instructions provided herein are made available for reference when installing the Aphos™ WA Luminaire and do not claim to represent all possible installation variations. If any portion of these installation instructions are unclear, then do not proceed with the installation and contact an EYE Lighting representative . Cet équipement est conçu pour être installé par un personnel qualifié. L’installation doit être conforme au “National Electric Code” (É-U) et (ou) à tout autre code du bâtiment de votre État, province ou municipalité. L’installation definitive doit être approuvée par un inspecteur en bâtiment et (ou) un électricien qualifié tel qu’approprié. Une installation inappropriée peut résulter en un risqué de feu ou de choc électrique. Les instructions ci-jointes sont fournies à titre de référence pour l’installation de l’ensemble luminaire. Ne procédez pas à l’installation si une partie de ces instructions n’est pas claire et contactez plutôt un représentant d’EYE Lighting. EQS-H-69-46-00032 Rev. No.: Installation Instructions Aphos™ RW Luminaires Ensure that supply power is off Open the Mount Door by placing a flat screw driver blade between the Latch Block and the Body and pulling down on the handle. Slide luminaire end over arm end, ensure that wires are not pinched, by looping them back into the arm end. Ensure that the end of the arm is seating on the right step of the stair block to keep the luminaire leveled. Secure the luminaire to the arm by applying 130 in-lb torque to the 5/16”-18 nuts on the clamp. (See Figure 1) Make the electrical connections per Figure 2 below if supply voltage is 120 to 277 VAC or Figure 3 if supply voltage is 347 / 480VAC and using 480V to 277V Step-Down Remote Mounted Autotransformer. Figure 1 Figure 2 Figure 3 EQS-H-69-46-00032 Rev. No: