pvc floor mat 32-913
Transcription
pvc floor mat 32-913
PVC FLOOR MAT 32-913-5005/5006/5007 Floor mat made out of vinyl material with a dissipative top layer, excellent grounding properties, easy to clean and superb durability. Product information : Static dissipative sheet vinyl flooring, DIF (semiconductive) Product ESD approval certificate Dnr 230-01-0027 Electronic and telecommunications industry, telephone exchanges, ADP-rooms, ammunition factories, operation and other surgical rooms of hospitals and other Application ESD-protected areas where static discharge may cause damage to sensitive devices or personnel Thickness 2,0 mm Weight 3000 g/m². Total roll weight 112 kg Roll length 25 m Width 150 cm Blue (32-913-5005) Colour Beige (32-913-5006) Grey (32-913-5007) Technical specifications : Fire resistance Emissions Sound insulation Dimensional stability Residual indentation Effect of castor chair Abrasion resistance volume lost Seam Strength Colour fastness Insulation resistance Resistance to ground Surface resistance Combination resistance (shoes/floor) Charging Thermal Resistance B1 M1 after 4 weeks TVOC < 200*g/m²h ∆Lw approx. 2dB <0,1% <0,005 mm Suitable ,0mm 3 Group T ≤ 2,0 mm EN 684 ≥7 > 100 kΩ 7 approx. 10 MΩ (1x10 ) 8 < 100 MΩ (1x10 ) 7 < 35 MΩ (3,5x10 ) <10 V 0,25 W/m K DIN 4102 Nordtest NT Built 358/1 ISO & DIN EN 434 EN 433 2,5h EN 425 EN 660 Pt2 ≥ 400 N/50mm ISO 105-B02 VDE 0100 / IEC30364-6-61 IEC 61340-4-1 EOS/ESD 7.11 IEC 61340-5-1 ESD STM 9.72-1999 Resistance to chemicals: Test period 24h and 2h (EN 423), after which the chemical was washed off Chemical 24h 2h Lye 10% Soda 10% Hydrochloric acid 10% Citric acid 10% Light fuel oil White spirit Acetic acid 30% Weak effect No effect Strong effect No effect No effect Weak effect No effect No effect No effect No effect No effect No effect No effect No effect 32-913-5xxx.doc – February 2009 Even electrical properties without carbon black on the surface ! This mat is a static dissipative flooring developed for facilities where static discharge may cause damage to sensitvie devices. These include for instance, electronics and tele-communication facilities and operating theatres in hospitals. This mat has no carbon black on the surface, yet it renders an even electrostatic performance due to its special product formulation. It also performs perfectly at low relative humidity environments. PVC floor mat meets the requirements for floors in standard EN 613405-1. Combination resistance with appropriate ESD-shoes is < 10 MΩ and charging is < 10 V. The reverse of this mat is conductive, and therfore conductive glue is not required for installation. This makes installation more convenient and economical. PVC floor mat maintains its electrical properties regardless of the glue. It also meets the requirements for an insulating floor insulation resistance > 100 kΩ. Installation Any surface suited for normal vinyl flooring will be suitable as a base for installation. RH of the concrete floor must not exceed 90% or or 3,5% by weight. The temperature of installation, subfloor and material should be at least +20°C. The backside of flooring has sufficient conductive properties, conductive adhesive is not required for installation. For the same reason, a metal grid on the subfloor is unnecessary. Regular vinyl flooring adhesive is suitable for installation. Adhesive manufacturers provide full information and recommendations on the use of their products. In public areas the floor must be rolled to achieve maximum adhesion. Rolling should be carried out before the adhesive dries. This is done to prevent the emergence of adhesive application lines and indentations on the finished floor surface. Avoid traffic on the floor and do not move furniture until the adhesive has completely dried. To provide a waterlight joint the seams of the flooring should not be hot welded using a PVC-rod. Also corners should be welded. Where welding is not possible, sealing should be carried out using a suitable welding paste. Air gun should be used on the reverse side of the flooring in order to avoid differences in gloss and damages on the floor surfaces. Maintenance and cleaning : Initial cleaning : Sweep the floor clean of any loose dirt. Wash with alkaline solution (containing glycol), use red pads or medium hard brushes when cleaning with scrubbing machine or a combination machine. Rinse. Polishing : If necessary, you can polish the floor with one thin coat of a so called antistatic wax. The suitability of the wax must be tested. The electrical insulation resistance must be tested after polishing. Waxing may weaken the conductivity of the flooring. Daily maintenance : damp or wet cleaning, depending on type of soiling. Use a neutral or mild alkaline detergent or protective substances. Larger surfaces require the of a combination machine. When necessary, a localized polishing can be carried on areas with most traffic. 32-913-5xxx.doc – February 2009 TAPIS DE SOL PVC 32-913-5005/5006/5007 Tapis de sol à base de vinyl avec une surface supérieure dissipatrice, d’excellentes propriétés de mise à la terre, facile à nettoyer et une très grande longévité. Information produit : Produit : Application Epaisseur Poids Poids du rouleau Longueur du rouleau Largeur Couleur Tapis de sol dissipatif, vinyle, DIF (semi-conducteur) Certificat ESD Dnr 230-010027 Industrie électronique et télécommunications, salles ADP, salles d'opération hospitalières et autres zones protégées contre les ESD où les décharges électrostatiques peuvent causer des dommages au personnel et aux matériaux sensibles . 2,0 mm 3000 g/m² 112 kg 25 m 150 cm Bleu (32-913-5005) Beige (32-913-5006) Gris (32-913-5007) Spécifications techniques: Résistance au feu : Emissions Sound insulation Stabilité dimensionnelle Empreinte résiduelle Utilisation chaise à roulette Résistance abrasive Solidité de la soudure Résistance couleur Résistance isolation Resistance au sol Résistance de surface : Résistance chaussures / sol Charge Résistance thermique B1 M1 après 4 semaines TVOC < 200*g/m²h ∆Lw approx. 2dB <0,1% <0,005 mm souhaitable ,0mm 3 Group T ≤ 2,0 mm EN 684 ≥7 > 100 kΩ 7 approx. 10 MΩ (1x10 ) 8 < 100 MΩ (1x10 ) 7 < 35 MΩ (3,5x10 ) <10 V 0,25 W/m K Résistance aux produits chimiques: Test de 24 h et 2 h (EN 423), après utilisation du produit Produit Effet après 24h Lessive 10% Faible Soda 10% Nul Acide hydrochlorique 10% Notable Acide citrique 10% Nul Light fuel oil Nul White spirit Faible Acide acétique 30% Nul DIN 4102 Nordtest NT Built 358/1 ISO & DIN EN 434 EN 433 2,5h EN 425 EN 660 Pt2 ≥ 400 N/50mm ISO 105-B02 VDE 0100 / IEC30364-6-61 IEC 61340-4-1 EOS/ESD 7.11 IEC 61340-5-1 ESD STM 9.72-1999 Effet après 2h Nul Nul Nul Nul Nul Nul Nul 32-913-5xxx.doc – February 2009 Propriétés électriques – sans carbone en surface ! Ce tapis est un revêtement de sol dissipatif destiné aux installations présentant des risques de décharges électrostatiques qui peuvent causer des dommages aux produits sensibles (installations de télécommunications et électroniques). Ce tapis n'a pas de carbone en surface. Sa composition lui confère de bonnes performances antistatiques et réponds aux exigences de la norme EN 61340-5-1. Combiné avec des chaussures ESD, sa résistance est < 10 MΩ à une charge < 10 V. La partie inférieure de ce tapis est conducteur et par conséquent une colle spéciale conductrice n'est pas nécessaire et la pose en est facilitée. Il convient également à un sol isolant de résistance > 100 kΩ. Installation : Ce tapis PVC se pose sur toute surface. Le taux d'humidité relative du sol ne doit pas excéder 90%. La température de l'installation, sol et matériel doit être au moins de + 20°C. La partie inférieure du tapis a des propriétés conductrices suffisantes. Un adhésif conducteur n'est donc pas nécessaire à l'installation. Pour la même raison, un revêtement métal n'est pas nécessaire sur la surface supérieure. Un adhésif de sol ordinaire suffit. Les fabricants de colle fournissent toutes les recommandations nécessaires à l'utilisation de leurs produits. Pour assurer une adhésion maximum, le tapis doit être roulé avant le collage afin de faciliter la pose et d'éviter les irrégularités sur la surface. Ne pas marcher, ni déménager les meubles avant le séchage complet de la colle. Pour garantir l'étanchéité , ce revêtement PVC ne doit pas être soudé à chaud avec une tige PVC. Les angles peuvent aussi être soudés. Si la soudure n'est pas possible, la fixation peut s'effectuer à l'aide d'une colle de soudage. Pour les zones proches du mur et afin d'éviter des irrégularités, utiliser un séchoir sur la partie inférieure du tapis. Entretien : Nettoyage régulier : Débarrasser le sol de toute poussière et saleté. Nettoyer le sol avec une solution alkaline (contenant du glycol) à l'aide d'une serpillère ou une brosse à récurer de dureté moyenne. Rincer Polissage : Si nécessaire, Un lustrage avec une fine couche de cire antistatique est possible. Avant toute utilisation de cire, celle-ci doit être testée. Un test de résistance isolante doit être effectué après le polissage. La cire peut affaiblir la conductivité du sol. Entretien journalier : Utiliser un nettoyant neutre ou mi-alcalin. Les grandes surfaces seront nettoyées avec une machine. Si nécessaire, un polissage partiel pourra être effectué sur les zones les plus utilisées. 32-913-5xxx.doc – February 2009