CONFIGURATION SWITCH Regulation with internal room sensor
Transcription
CONFIGURATION SWITCH Regulation with internal room sensor
USER GUIDE THERMOSTAT T90-EB EN CONFIGURATION SWITCH 15.10.15-01EN 1 2 3 4 On Off Switch 3 and 4: Sensors configurations Regulation with internal room sensor Regulation with external sensor Switch 2: Type of regulation Static differential Optional external sensor 10K at 25°C Proportional (PWM) DESCRIPTION LED INDICATOR • Red: Green: Orange: Green blinking: • • • Electronic thermostat with “dual sensing” for electrical heating systems: radiant panels, underfloor heating, panel radiators etc. External pilot wire for night reduction, equipped with a 3-position switch to select different mode: Clock / Comfort / Reduction. Clock = night reduction with 4°C by pilot wire (external clock), Comfort = Normal operation, Reduction = fixed reduction of 4°C. Possibility to regulate either the room or floor temperature, or combined (in this case, the optional floor sensor is used as a temperature limiter). Main switch, ON/OFF. Select mode: Clock/Comfort/Reduction Main switch Floor limit setting LED Indicator Temperature setting Terminal for external sensor and pilot wire Regulation on internal room sensor combined with the external sensor used in floor limitation (upper) Heating indication Reduction mode by external clock (pilot wire) Heating indication during reduction mode by external clock 0.5 second cycle => Internal and external sensor failures 1 second cycle => Internal sensor failure 2 seconds cycle => External sensor failure TECHNICAL CHARACTERISTICS Operating voltage, power supply 230V~ +/- 10% Rated current / Relay 16A resistive load, 230V~ Appliance and protection class Class II - IP30 Setting range, temperature 5°C – 30°C (41°F – 86°F) Operating temperature 0°C – 50°C (32°F – 122°F) Switching differential 0.1°C (0.2°F) Regulation characteristics Proportional band 10 min for 2K or static differential 0.5K Floor limitation, temperature range 10°C – 40°C (50°F – 104°F) Optional external floor sensor NTC (10K Ohms) Configuration switch Terminal for power supply and output Regulation on internal room sensor combined with the external sensor used in floor limitation (lower) Energotech AB | Box 8053 | SE-200 41 Malmö, Sweden | +46 40 866 90 | [email protected] | www.energotech.com GUIDE D’UTILISATION THERMOSTAT T90-EB FR INTERRUPTEURS DE CONFIGURATION 15.10.15-01FR 1 2 3 4 On Off Switch 3 et 4: Configurations des sondes Régulation sur sonde interne Régulation sur sonde externe Switch 2: Type de régulation Hystérésis Bande Proportionn. Régulation sur sonde interne combinée avec la sonde externe utilisée en en limitation basse de la température de dalle Régulation sur sonde interne combinée avec la sonde externe utilisée en en limitation haute de la température de dalle Option - Sonde externe 10K à 25°C FONCTION et DESCRIPTION VOYANT D’ETAT • Rouge fixe: Vert fixe: Orange fixe: Vert clignotant: • • • Thermostat électronique « dual sensor » équipé de sonde de sol et d’ambiance destiné à la régulation des systèmes de chauffage électriques. Fil pilote externe, pour un abaissement fixe de 4°C.3 modes de fonctionnement => Horloge / Confort / Eco Régulation sur sonde interne, externe ou les deux combinées. Dans ce cas là la sonde de sol (externe) est généralement utilisée en limitation de température de la dalle. Interrupteur, ON/OFF. Thermostat en chauffe Indication d’ordre d’abaissement (4°C) Thermostat en chauffe pendant un abaissement Flash de 0.5 seconde => Défaut sur les deux sondes Flash de 1 seconde => Défaut sur sonde interne Flash de 2 secondes => Défaut sur sonde externe CARACTERISTIQUES TECHNIQUES Voyant d’état Sélecteur de mode Interrupteur Température de limitation (sonde sol) Température de confort Interrupteurs de configuration Bornier d’alimentation et de sortie Bornier de sonde externe et fil pilote Alimentation 230V~ +/- 10% Sortie / Relais 16A / 230V~ Protection Class II - IP30 Plage de réglage de la température d’ambiance 5°C – 30°C Température de fonctionnement 0°C – 50°C Précision de mesure 0.1°C Caractéristique des différentes régulations Plage de réglage de la température de limitation dalle Bande proportionnelle de 2°K pour un cycle de 10 minutes ou hystérésis de 0.5°K Sonde externe en option CTN 10K 10°C – 40°C Energotech AB | Box 8053 | SE-200 41 Malmö, Suede | +46 40 866 90 | [email protected] | www.energotech.com