Wood Trim Fluorescent Fixture NEED HELP?

Installation Instructions for
WOODTrim
TRIM LED
FIXTURE Fixture
Wood
Fluorescent
GENERAL PRODUCT INFORMATION:
This product is suitable for damp locations.
This instruction shows a typical installation.
CAUTION - RISK OF FIRE
This product must be installed in accordance with the
applicable installation
code by
a person
CAUTION
- RISK
OFfamiliar
FIRE with the
construction
operation
of the by
product
and the
hazards
This product and
requires
installation
a qualified
electrician.
involved.
Before installing be sure to read all instructions and
NEED HELP?
If you need installation
assistance, replacement
parts, or have questions
regarding our warranty,
please call our customer
service number:
TURNminimum
THE POWER
TO THE
ELECTRICAL
BOX OFF.
Use
90°c
supply
conductors.
MISE EN GARDE - RISQUE D'INCENDIE
Ce produit doit être installé selon le code d’installation
pertinent , par une personne qui connaÎt bien le produit et
son fonctionnement ainsi que les risques inhérents
Les fils d’alimentation doivent convenir pour
90°c.
ADVERTENCIA - RIESGO DE INCENDIO
Este productor debe ser instalado segun el codigo de
instalacion aplicable por una persona que conozca la
constussion y el funcionamiento del producto y los riesgos
que supone.
Conductores de alimentacion 90°c Min.
1-800-841-4666
www.Brodwax.com
SAVE THESE INSTRUCTIONS!
SAVE THESE INSTRUCTIONS!
Warranty
Brodwax Lighting fixtures and components, when properly installed and under normal conditions of use, are warranted to be free rfom defects in materials
and workmanship for three years from date of sale. LED light sources are warranted for five years. ENERGY STAR® labeled products are warranted for
three years. Brodwax Lighting at its sole option will repair or replace, F.O.B. Factory, freight prepaid, any Brodwaxl Lighting product defective in materials or
workmanship. Such replacement is the exclusive remedy against Brodwax Lighting should any of the products delivered prove defective. Invoices for labor
charges and/or charge backs for labor will be denied unless prior written approval is given.
Any modification to a Brodwax Lighting product not made at the factory will void the UL or ETL listing as well as the Brodwax warranty policy
Garantía
Los accesorios y componentes Brodwax Lighting, cuando son correctamente instalados bajo condiciones de uso normal, se garantizana estar libres de
defectos en materiales y trabajo manual por un año de la fecha de compra. Lámparas LED tienen una garantía de cinco años. Los productos etiquetados
ENERGY STAR® se garantizan por tres años. Brodwax Lighting a su propia opción reparará o reemplazará, F.O.B. Factory, flete pre pagado, cualquier
producto de Brodwax Lighting defectuoso en materiales o trabajo manual.Tal reemplazo es el remedio exclusivo en contra de Brodwax en caso de
que cualquiera de sus productos entregados esté defectuoso. Facturas por cargos de labor y/o cargos al usuario por labor serán negados a menos de que
se haya recibido permiso previo por escrito.
Cualquier modificación hecha a un producto de Brodwax Lighting no llevado a cabo en la fábrica
anulara el listado de UL o ETL al igual que la póliza de garantía de Brodwax Lighting.
Garantie
A la condition d'un montage et d'une utilisation dans les normes, les Luminaires et pièces Brodwax Lighting sont garantis sansdéfauts des matériaux et
dans leur fabrication pour une durée d'un an à compter de la date d'achat. Sources de lumière LED sont garantis pour cinq ans. Les produits labellisés
ENERGY STAR® sont garantis pour trois ans.A sa seule discrétion, Brodwax Lighting réparera ou remplacera tout produit BrodwaxLighting défectueux
dans ses matériaux ou dans sa fabrication, F.O.B. Usine fret payé d'avant. Un remplacement selon ces conditions est l'unique recours à l'encontre de Sea
Gull Lighting dans le cas où les produits livrés se révèlent défectueux.Toute facture concernant des frais de main d'oeuvre et/ou toute demande de
remboursement de main d'oeuvre sera rejetée à moins qu'un accord écrit ait été consenti au préalable.
Toute modification non effectuée par l'usine d'un produit Brodwax Lighting conduira à l'annulation des enregistrements UL ou ETL ainsi que du contrat de
garantie Brodwax Lighting.
Install the Fixture
1A
FIXTURE
3
2
1
8
CHANNEL
9
CHANNEL
COVER
LAMP
DIFFUSER
For 2x2, Use
linear lamp.
4 - 11 Watt type
For 2x4, Use 4
linear lamp.
LED high output
- 22 Watt type LED high output
1
Remove channel cover by squeezing at each end in the xture channel. Remove appropriate knockout(s) for power
supply entry.
2
Position the xture channel onto the ceiling and mark all appropriate mounting hole locations. NOTE: Assistance will
be required for this step.
3
Punch a small hole in the ceiling at each marked location to see if there is a wood joist above that can be used to
mount the xture. NOTE: For wood joist, use a suitable wood screw (not included) to mount the fixture. If there
is no joist to screw into, a 3/16” toggle bolt (not included) must be used to mount the fixture channel securely
to the ceiling. This product includes foam tape which may be used to seal any gaps between the fixture and
ceiling.
4
Connect the xture to a suitable ground in accordance to local electrical codes.
5
Connect the white ballast wire to the neutral power line wire with a wire nut.
6
Connect the black ballast wire to the hot power line wire with a wire nut.
7
Replace ballast cover by placing one edge of ballast cover into dimples, swing upward, and press cover allowing
second edge to catch second set of dimples and lock in place. Make sure no wires become crimped between cover
and xture.
8
Install the lamps (LED - included) by aligning the lamp pins with the socket slots, then pushing the pins all the way
into the socket slots and rotating the lamp until it clicks into place. Repeat for remaining lamps.
9
Install the trim cover - Lift the trim end with the metal L bracket up to the ceiling and slide the bracket between
the fixture body and ceiling. Once the bracket is fully in position, swing up the opposite end until flush with
the ceiling, and install the provided countersunk screw through the hole in the trim and into the hole in the body..
10
For re-lamping, remove the trim cover by removing the screw, swing that end down, then slowly push the opposite
end off past the frame and guiding it down. Reverse step 8 for re-lamping.