peugeot 406 - Bis Alarmes
Transcription
peugeot 406 - Bis Alarmes
SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00 www.cobra.it MAKE PEUGEOT MOD. 406* YEAR. 02 → PETROL DIESEL X * Models with original equipment keyless entry system. ALARM/SIREN POSITION Position the compact alarms and the sirens on the dome of the shock absorber, passenger’s side. CENTRAL UNIT POSITION Position the modular systems and the modules under the dashboard, driver’s side. POWER SUPPLY + 30: connect to the 3 mm RED wire located at the entrance of the fuse box. - 31: connect to one of the original ground terminals located on the right of the BSI operating central.. IGNITION WIRE + 15/54: connect to the wire at the position nr. 16 coming out of the 26 way blue connector of the BSI operating central. DIRECTION INDICATORS Connect to the wires at the positions nr. 13 and nr. 14 of the 16 way black connector coming out of the BSI operating central. ELECTRIC WINDOWS Positive control signal Front window, driver’s side: Refer to the diagram nr. 114. Front window, passenger’s side: 2 Cut the 1 mm GREY wire located at the position nr. 10. Rear window, driver’s side: 2 Cut the 1 mm VIOLET wire located at the position nr. 7. Rear window, passenger’s side: 2 Cut the 1 mm GREY wire located at the position nr. 6. These connections are made directly in the 16 way black connector coming out of the push-button panel in the armrest of the driver’s side door. ACTIVAT./DEACTIVATION CONTROLS Connections antitheft/vehicle Refer to the diagram nr. 115. IMMOBILISATION POINT Gasoil pump Cut the GREY wire located in the wiring harness coming out of the connector of the inertial switch. STARTER + 50: Cut the BLUE wire located in the wiring harness coming out of the 3 way connector, on the left of the steering column. BONNET SWITCH Install an additional switch on the front headlamp support plate, driver’s side. DOORS SWITCH Connect to the wire, at the position nr. 14 coming out of the 26 way blue connector of the BSI operating central. Note: The lamp polarity is positive. BOOT SWITCH Break version: connect to the wire located at the position nr. 7 coming out of the 26 way blue connector of the BSI operating central. Other versions: connect to the WHITE wire marked 315 directly in the connector coming out of the boot lamp. 2 Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed as per the instructions given on the product installation manual. pe40602gbdt.doc SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00 www.cobra.it FITTING DIAGRAM N° 115 Diagram for the interfacing of art. 3800 on PEUGEOT 406 year 2002 Art. 3800 26 way blue connector 16 way black connector ORANGE/WHITE nr.10 nr.23 nr.4 nr.3 +30 YELLOW/BLACK GREY/BLACK VIOLET/WHITE ground Diodes 1N4004 M VIOLET ORANGE Driver’s side door’s switch AP AP Passenger’s side door’s switch Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed as per the instructions given on the product installation manual. pe40602gbdt.doc SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00 www.cobra.it FITTING DIAGRAM N° 114 Diagram for windows connection on PEUGEOT 406 year 2002 Diagram for windows locking using the BROWN/WHITE wire of the autodriven Bridge serie antithefts. Left push botton 1052 1 2 3 4 16 way black connector 5 +30 position nr.12 YELLOW Diode 1N4004 BROWN/WHITE Diagram for windows locking using the BROWN wire of the no autodriven Bridge serie, 3100 and 3800 antith efts. Left push botton 1055 1 +30 2 3 4 5 16 way black connector 6 7 position nr.12 YELLOW Diode 1N4004 BROWN Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed as per the instructions given on the product installation manual. pe40602gbdt.doc