Schéma collier « Muse »
Transcription
Schéma collier « Muse »
Schéma collier « Muse » Matériel : Pour un collier de 43cm 34 Arcos®par Puca®(A), 32 Ios®par Puca®(I),32 rondes aplaties 4mm(RA4), 32 rondes aplaties 3mm (RA3), 5grs de rocailles 15mm(R15), 2 rocailles 8mm(R8), 1 fermoir de votre choix:), Fil fireline 0,15 Allons-y : 1 Mettre 1 Ios, 1R15, 1Arcos, 1R15, 1Arcos, 1R15, 1 Ios, 1R15 2 Fermer et se placer dans la Ios 3 On obtient ceci 4 Passer dans le 2iéme trou de la IOS 5 Mettre 3 R15, 1R8, 3R15 Passer dans la Ios 6 Je fais 3 fois le tour pour consolider et je reviens placer mon fil ICI (Etoile) 7 Mettre 1R15, 1Arcos, 1R15, 1Arcos, 1R15, 1Ios, 1R15, je passe dans mon Arcos, Je continue ainsi comme étape 2 . 8 A la fin mettre comme étape 5 3R15, 1R8, 3R15, 9 Venir placer votre fil Ici 10 Placer 1RA4 entre les Arcos tout le long etc … 11 On obtient ceci:) 12 Faire de l’autre côté avec les RA3 Vous avez terminé ! Reste à placer votre fermoir:) Je vous souhaite un agréable perlage avec les perles par Puca® Merci de respecter mon travail® Puca … le 8 Novembre 2016 Necklace pattern "Muse" You need: For a necklace of 43cm ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ 72 Arcos® by Puca® (A) 36 Ios® by Puca® (I) 36 Fire Polished Rondelles 4mm (FP4) 36 Fire Polished Rondelles 3mm (FP3) 5 grams Seeds Beads 15/0 (SB15) 2 Seeds Beads 8/0 (SB8) 1 clasp of your choice :) Fireline wire 0.15 mm Let's go: 1. Pick up 1 Ios, 1SB15, 1Arcos, 1SB15, 1Arcos, 1SB15, 1 Ios, 1SB15. 2 Close the beads into a circle: Pass through the second hole of the Arcos you just picked up. Pick up 1SB15 and pass through the second hole of the Arcos you first picked up in this step. Pick up 1 SB15 and pass through the first Ios you picked up in this step (see picture). 3 Pull your thread to get this result. 4 Pass back through the second hole of the Ios. 5 Pick up 3SB15, 1SB8, 3SB15 and pass through the second hole of the Ios again. 6 Repeat the thread path 3 more times to reinforce that loop and follow the thread path in the picture to exit the second Ios (star in the picture). 7 Pick up 1SB15, 1Arcos, 1SB15, 1Arcos, 1SB15, 1Ios, 1SB15 and pass back through the second hole of the Arcos you last picked up. Continue repeating step 2 from step 7. 8 When you reach the desired length of your necklace, repeat step 5: 3SB15, 1SB8, 3SB15, 9 Follow the thread path in the picture (star). 10 Place 1FP4 between all the Arcos 11 This is the result :) 12 Repeat step 10 on the other side with FP3 You have finished the necklace! Only thing left to do is to attach your clasp :) I wish you pleasant beading with beads by Puca® Thank you for respecting my work®