SET-XP High Performance Epoxy Resin - Simpson Strong-Tie

Technical data sheet
SET-XP - HIGH PERFORMANCE EPOXY RESIN
SET-XP is an epoxy based
resin suitable for use in
cracked or non-cracked
concrete. It is also rated for
use in seismic conditions.
ETA-11/0360, UK-DoP-e11/0360, FDS-SETXPA(3.2)UK, FDS-SETXP-B(3.2)UK
FEATURES
Matière
100% Epoxy
Avantages
•
•
•
Seismic approved.
Suitable for use in hot/humid conditions
Ideal for high diameter fixings.
APPLICATIONS
Support
Concrete
Domaines d'utilisation
•
•
Heavy duty steel structures.
Structures requiring seismic protection.
Winchester Road Cardinal Point Tamworth Staffordshire B78 3HG
Tél. : +44 1827 255600 / Fax : +44 1827 255616
Information presented on this document is the exclusive property of Simpson Strong-Tie®
It is valid only when associated with products supplied by Simpson Strong-Tie®
SET-XP - High Performance Epoxy Resin
2016-12-02
page
1/3
www.strongtie.co.uk
Technical data sheet
SET-XP - HIGH PERFORMANCE EPOXY RESIN
TECHNICAL DATA
Model
References
SET-XP650-FR
SET-XPTM 650
Code article
SET-XP650-FR
SET-XP650-DE
Contenu [ml]
650
650
Poids [kg]
1.05
1.05
2 nozzles are provided with each cartridge
Recomended loads
References
SET-XP + LMAS M12 (hef=70mm)
SET-XP + LMAS M12 (hef=240mm)
SET-XP + LMAS M16 (hef=80mm)
SET-XP + LMAS M16 (hef=320mm)
SET-XP + LMAS M20 (hef=90mm)
SET-XP + LMAS M20 (hef=400mm)
SET-XP + LMAS M24 (hef=100mm)
SET-XP + LMAS M24 (hef=480mm)
SET-XP + LMAS M27 (hef=110mm)
SET-XP + LMAS M27 (hef=540mm)
Profondeur
d'implantation
[hef] [mm]
70
240
80
320
90
400
100
480
110
540
Traction [Rds,N] [kN]
Béton fissuré
Béton non
C20/25
fissuré C20/25
5.4
10
18.4
20
6.1
12.3
24.6
37.6
5.7
14.6
25.6
58.5
7.6
17.1
36.9
84.2
9.5
19.8
46.7
109
Cisaillement [Rds,V] [kN]
Béton fissuré
Béton non
C20/25
fissuré C20/25
12
12
21
12
17.2
22.2
22.2
22.2
16.1
34.8
34.8
34.8
21.6
48
50.2
50.2
26.6
55.4
65.7
65.7
Moment
de flexion
[Mrds] [Nm]
37.7
37.7
94.8
94.8
185.7
185.7
320.5
320.5
475.4
475.4
1) The design resistances have been calculated using the partial safety factors for resistances stated in ETA- approvals(s).
The recommended loads have been calculated using the partial safety factors for resistances stated in ETA-approval(s) and with a partial safety factor
for actions of #f=1.4.
2) The load figures are valid for reinforced concrete with a rebar spacing # 15cm (any diameter) or with a rebar spacing # 15cm if the rebar diameter is
10mm or smaller.
4) The figures for shear are based on a single anchor without influence of concrete edges. For anchorages close to the edges (c # hef 60d) the concrete
edge failure shall be calculated per EOTA Technical Report - TR 029 or acc. to CEN/TS 1992-4.
5)Temperatur range I: -40°C to +43°C (max. long-term temperatur: +24°C; max. short-term temperatur: +43°C).
6) When installed in wet concrete, the curing times are double (installation in holes filed with water is not allowed).
Winchester Road Cardinal Point Tamworth Staffordshire B78 3HG
Tél. : +44 1827 255600 / Fax : +44 1827 255616
Information presented on this document is the exclusive property of Simpson Strong-Tie®
It is valid only when associated with products supplied by Simpson Strong-Tie®
SET-XP - High Performance Epoxy Resin
2016-12-02
page
2/3
www.strongtie.co.uk
Technical data sheet
SET-XP - HIGH PERFORMANCE EPOXY RESIN
INSTALLATION
Temps de pose
Substrate Temperature (°c)
Working Time
Curing Time
Drill.
10° to 20°
60 mins
72 hours
Remove dust
by brushing and
blowing,
21° to 30°
45 mins
24 hours
Fill the hole
to half or
two thirds,
Withdrawing
the nozzles with
each pump.
31° to 40°
25 mins
24 hours
Insert the rod,
turning slowly.
Once set, full
load capacity is
reached.
Installation Details
References
SET-XP + LMAS M12 (hef=70mm)
SET-XP + LMAS M12 (hef=240mm)
SET-XP + LMAS M16 (hef=80mm)
SET-XP + LMAS M16 (hef=320mm)
SET-XP + LMAS M20 (hef=90mm)
SET-XP + LMAS M20 (hef=400mm)
SET-XP + LMAS M24 (hef=100mm)
SET-XP + LMAS M24 (hef=480mm)
SET-XP + LMAS M27 (hef=110mm)
SET-XP + LMAS M27 (hef=540mm)
Ø
Prof.
perçage perçage
[d0] [mm] [h0] [mm]
14
14
18
18
24
24
28
28
30
30
Ø max
Ouverture
pce à
de clé sur
fixer [df]
plat [Sw]
[mm]
70
240
80
320
90
400
100
480
110
540
14
14
18
18
22
22
26
26
30
30
Winchester Road Cardinal Point Tamworth Staffordshire B78 3HG
Tél. : +44 1827 255600 / Fax : +44 1827 255616
Information presented on this document is the exclusive property of Simpson Strong-Tie®
It is valid only when associated with products supplied by Simpson Strong-Tie®
19
19
24
24
30
30
36
36
41
41
Couple
serrage
[Tinst]
[Nm]
40
40
60
60
80
80
100
100
120
120
Dist.
entraxes
(4)
caract.
- Scr,N
[mm]
210
720
240
960
270
1200
300
1440
330
1620
Dist.
entraxe
mini Smin
[mm]
45
45
60
60
70
70
80
80
90
90
Dist. au
bord
SET-XP - High Performance Epoxy Resin
2016-12-02
(4)
caract.
- Ccr,N
[mm]
105
360
120
480
135
600
150
720
165
810
Dist. au
bord mini
- Cmin
[mm]
80
80
100
100
115
115
135
135
155
155
page
3/3
www.strongtie.co.uk
Ep.
mini du
support
[hmin]
[mm]
100
270
116
356
138
448
156
536
170
600