Parts Manual Ersatzteilliste Manuel de pièces détachées 35D Fork
Transcription
Parts Manual Ersatzteilliste Manuel de pièces détachées 35D Fork
Parts Manual Ersatzteilliste Manuel de pièces détachées c 35D Fork Positioners 35D Zinkenverstellgeräte 35D Ajusteurs de Fourches cascade ® Parts Manual - SEL 58864 Last update: 05/08/02 35D Fork Positioner 1 Cascade Parts Manual 35D Fork Positioner 2 Cascade Parts Manual Introduction How to use this manual Important This manual illustrates service replacement parts for standard production Cascade clamps. To locate a particular part refer to the Unit Identification Index (U.I.Index) directly preceeding the parts list section of this manual. Parts manuals for Cascade Application Egineering Department will have an AED designation followed by an AED number on the cover of the manual. To locate a particular part in an AED manual turn to the page with the related group heading (i.e. Frame Group, Check Valve Group, etc.) If there is more than one parts list on the page, use the list indicated with a red arrow. Quantites shown in both manuals are for one complete assembly unless otherwise indicated. Standard parts manuals are not interchangeable with AED manuals and will not reflect the special engineering of the AED products. When ordering replacement parts, always give the attachment unit identification number, part number, description of part and quantity required. For further information on parts, maintenance or ordering, consult your lift truck dealer. ATTACHMENT CAPACITY LIFT TRUCK ATTACHMENT SERIAL NUMBER CATALOG NUMBER ADDITIONAL EQUIPMENT ADDITIONAL EQUIPMENT ADDITIONAL EQUIPMENT WEIGHT LBS. POUNDS INCH LOAD AT CENTER CAPACITY OF TRUCK AND ATTACHMENT COMBINATION MAY BE LESS THAN ATTACHMENT CAPACITY SHOWN ABOVE. CONSULT TRUCK NAMEPLATE. RECOMMENDED SYSTEM PRESSURE – 2000 PSI MAXIMUM SYSTEM PRESSURE – 2300 PSI T FOR TECHNICAL ASSISTANCE, CONTACT 800-227–2233 PORTLAND, OREGON USA FOR PARTS AND SERVICE MANUALS, CONTACT 800-227–2233 SPRINGFIELD, OHIO USA Nameplate CL0661a.eps Reading the Attachment Nameplate Unit Identification Number Cascade’s nameplate is riveted to the clamp frame. This plate shows clamp size and model, type, rated capacity, serial, unit identification and catalogue numbers. The serial and unit identification numbers are stamped under the nameplate as well as on the nameplate itself. The Unit Identification (U.I.) Number indicates the specific combination of component parts used in each individual Clamp. Two units may have the same catalogue number yet may incorporate components of different design modifications. The U.I. Number Index gives the page number for required parts, and allows the person receiving parts order to double check in case of an error in ordening. Parts Index When using the parts list index, first locate the U.I. number on the attachment nameplate. List this number and refer to the index located in the of this manual. Locate your U.I. number in the first column.Columns to the right will refer you to the proper page number for a particular parts group. We reserve the right to make changes in our design and add improvement without notice. 35D Fork Positioner 3 Cascade Parts Manual Benutzungshinweis Wichtig Benutzungshinweis Dieses Handbuch gilt nur für standard Klammern und In diesem Handbuch sind alle Ersatzteile die zur ist nicht verwendbar für Anbaugeräte, die speziell Wartung und Instandsetzung der Cascade Klammern gefertigt wurden und mit “AED” gekenntzeichnet sind. benötigt werden, abgebildet, bezw. erläutert. Die Bilder und Stücklisten enthalten Teilnummern, Bezeichnungen, benötigte Mengen, Schlüssel- und Fuß- noten, die das Auffinden der richtigen Bauteile erleichtern. Die angegebenen Mengen gelten für einen kompletten Zusammenbau, sofern das nicht anderweitig angegeben ist. ATTACHMENT CAPACITY LIFT TRUCK ATTACHMENT SERIAL NUMBER CATALOG NUMBER 791423 D001 40D-FP-511A POUNDS INCH LOAD AT CENTER CAPACITY OF TRUCK AND ATTACHMENT COMBINATION MAY BE LESS THAN ATTACHMENT CAPACITY SHOWN ABOVE. CONSULT TRUCK NAMEPLATE. WEIGHT LBS. RECOMMENDED SYSTEM PRESSURE – 2000 PSI MAXIMUM SYSTEM PRESSURE – 2300 PSI ADDITIONAL EQUIPMENT T ADDITIONAL EQUIPMENT FOR TECHNICAL ASSISTANCE, CONTACT 800-227–2233 PORTLAND, OREGON USA ADDITIONAL EQUIPMENT FOR PARTS AND SERVICE MANUALS, CONTACT 800-227–2233 SPRINGFIELD, OHIO USA Typenschild CL0661b.eps Typenschild Anbaugerät-Nummer-Index Folgende Angaben sind auf dem Typenschild verzeichnet: Anbaugeräte Nummer Anbaugeräte Bezeichnung Serien Nummer Tragfähigkeit Sollte das Typenschild entfernt oder beschädigt sein, kann die Serien Nummer die noch zusätzlich unter dem Typenschild im Rahmen eingeschlagen ist, zur Erkennung des Gerätes dienen. Dieser index hilft beim schnellen Identifizieren der im Anbaugerät verwendeten Ersatzteile. Im Interesse der Produktentwicklung unterliegt jede in diesem Handbuch gemachte Einzelangabe einer Abänderung ohne vorherige Mitteilung. 35D Fork Positioner 4 Cascade Parts Manual Introduction Introduction Important Ce manual comprend les pièces de rechange des Pince Cascade. Pour repérer une référence de pièces, il convient de se référer d’abord au tableau d’identification des sous- ensembles. Les manuals pour les produits spéciaux sont reconnus par la référence AED suivie d’un numéro et mentionné sur la couverture du manuel. Les références de pièces figurent sous chaque sous ensemble et parfois indiqués par une flèche rouge. Les quantités indiquées sont celles nécessaires pour un ensembles complet sauf mention contraire. Les manuels couvrant les produits standard ne sont pas interchangeablas avec les manuels AED. Lors d’une commande de pièces il est préférable d’indiquer le numéro de série de l’accessoire, la références et la désignation. Pour toutes informations consulter votre constructeur de chariots. ATTACHMENT CAPACITY LIFT TRUCK ATTACHMENT SERIAL NUMBER CATALOG NUMBER 791423 D001 40D-FP-511A WEIGHT LBS. ADDITIONAL EQUIPMENT ADDITIONAL EQUIPMENT ADDITIONAL EQUIPMENT POUNDS INCH LOAD AT CENTER CAPACITY OF TRUCK AND ATTACHMENT COMBINATION MAY BE LESS THAN ATTACHMENT CAPACITY SHOWN ABOVE. CONSULT TRUCK NAMEPLATE. RECOMMENDED SYSTEM PRESSURE – 2000 PSI MAXIMUM SYSTEM PRESSURE – 2300 PSI T FOR TECHNICAL ASSISTANCE, CONTACT 800-227–2233 PORTLAND, OREGON USA FOR PARTS AND SERVICE MANUALS, CONTACT 800-227–2233 SPRINGFIELD, OHIO USA Plaque d'identification CL0661c.eps Lecture de la plaque d’identification Numéro de référence Une plaque CASCADE est rivetée ou coullée sur le chassis de la pince, les informations mentionnées sont: le taille et le modèle, le type, la capacité, le numéro de série, la références et le numéro du catalogue. Le numéro de série et la référence sont également gravés sous la plaque. Ce numéro indique la composition des sous ensembles de la Pince. Deux accessoires peuvent avoir le même numéro de catalogue et cependant avoir une composition différente. Cette référence permet de localiser la référence des pièces et de vérifier la commandé. Index des pièces Lors de l’utilisation de l’index il convient en premier lieu de relever le numéro de référence de la Pince et se reperter l’index pour connaître les sous-ensembles. CASCADE se réserve le droit d’effectuer toutes modifications et améliorations sans notice. 35D Fork Positioner 5 Cascade Parts Manual Safety decal Warnungsschild Auto-collant 2 1 2 fi e ad sc ca fi e fi e ad ad sc sc ca ca 3 CLAMPS WITHOUT ARMS FORKS, DRUM ARMS 1 BALE ARMS MULTI-PURPOSE ARMS 2 3 Quick Change Hooks Disengaged from carriage UNLOCKED POSITION Engaged to carriage LOCKED POSITION e e ad ca -1 14 5 75 C-6 CL0497a.eps Ref. Qty. 1 2 3 1 4 1 Part No. Description 679150 665595 679059 35D Fork Positioner Bezeichnung No step decal Warnungsschild No hand hold decal Warnungsschild Quick change hook decal Warnungsschild 6 ad sc sc ca Lower Carriage Bar 4-1 51 75 C-6 67905 9 Description Auto-collant Auto-collant Auto-collant Cascade Parts Manual Frame and Mounting Group Rahmen und Aufhängungsgruppe Groupe Bâti et Accrochage L-790108 1 3 5 12 4 6 13 14 2 11 10 9 8 7 Ref Qty Part No. 1 2 3 4 5 6 7 8 ▲9 ▲10 ▲11 12 13 14 1 1 1 8 8 1 2 2 4 4 4 2 2 1 788964 788963 772289 772299 772313 773820 768414 773842 667907 667663 667906 7861 7962 780302 Description Bezeichnung Description Mounting plate LH Mounting plate RH Guide profile upper Capscrew, M12x70 Washer Bumper Capscrew, M12x65 Nut Bearing Bearing Bearing Roll pin Roll pin Guide profile lower Aufhängungsplatte L Aufhängungsplatte R Führungsträger oben. Kopfschraube, M12x70 Unterlegscheibe Schutzschild Kopfschraube, M12x65 Mutter Gleitschiene Gleitschiene Gleitschiene Spannhülse Spannhülse Führungsträger unter. Plaque d’accrochage G Plaque d’accrochage D Profilé guide sup. Vis à tête, M12x70 Rondelle Plaque protectrice Vis à tête, M12x65 Ecrou Glissière Glissière Glissière Goupille roulée Goupille roulée Profilé guide inf. ▲Order Bearing Kit 229189 / Bestellen Sie Gleitschienesatz 229189 / Commander Kit de Glissière 229189 Check Valve Group Sperrventilgruppe Ensemble Valve de Controle L772327 Ref Qty Part No. Description Bezeichnung Description 1 2 3 4 5 6 7 8 9 10 11 Valve assembly Capscrew Lockwasher Valve bracket Screw Restrictor Adapter fitting Tube Tube Tube Tube Ventil Zusammenbau Kopfschraube Unterlegscheibe Ventil-Aufbauplatte Schraube Drossel Verschraubung Rohr Rohr Rohr Rohr Ensemble de clapets Vis à tête Rondelle Support Vis Limiteur de débit Raccord Tuyau Tuyau Tuyau Tuyau 8 Cascade Parts Manual 1 4 4 1 2 2 8 1 1 1 1 667479 770679 6258 667682 770671 667609 774501 774175 774176 774004 774005 35D Fork Positioner 35D Check Valve for side shifting Fork Positioners Sperrventil für Zinkenverstellgeräte mit Seitenschub Valve de controle pour Ajusteurs de fourches à déplacement latéral Assy no. 667479 Ref Qty Part No. Description Bezeichnung Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 667480 667470 2841 667471 667510 609455 2839 667476 667516 661347 659058 678270 2701 667611 2841 667610 5716 604510 Relief valve Fitting-special O-Ring Spool Seal kit-relief valve O-Ring plug O-Ring Valve body Seal kit-check valve Seal kit-check valve P.O. Check valve SS V.P.O. Check valve CI. O-Ring Plunger-threaded O-Ring Restrictor body Jam nut O-Ring plug JIC 6 Druckbegrenzungsventil Spezialverschraubung O-Ring Spule Dichtsatz O-Ring Stopfen O-Ring Ventilgehause Dichtsatz Dichtsatz Rückschlagventil Seit. Rückschlagventil Klam. O-Ring Gewindestift O-Ring Drosselgehause Kontermutter O-Ring Stopfen JIC 6 Valve de décharge Raccord spécial Joint torique Tiroir Kit de service Bouchon à joint torique Joint torique Corps de clapets Kit de service Kit de service Valve anti-retour depl.lateràl Valve anti-retour serrage Joint torique Plangeur-fileté Joint torique Corps du limiteur de debit Ecrou de verrouillage Bouchon à joint torique JIC6 1 1 1 1 1 3 4 1 2 1 2 1 1 1 1 1 1 1 ▲ ▲ ▲ ▲ ▲ ▲ Included in service kit 667512 containing all O-rings and back-up rings for this valve assembly. Note that O-ring plugs and cartridge valves are supplied complete with O-rings and back-up rings. ▲ Enthalten im Dichtsatz 667512 (alle O-Ringe und Stutzringe verwendet in dieses Ventil). Achten Sie darauf , O-Ringe, Stopfen und Kartuscheventile komplett mit O-Ringe und Stuzringe geliefert werden. ▲ Inclus dans le kit de service 667512 qui content tous les joints pour cet ensemble de clapets. Il est à noter que les bouchons et valves à cartouches sont livrées avec tous les joints déjà installés. 35D Fork Positioner 9 Cascade Parts Manual 35D Cylinder Group Zylinder Gruppe Groupe Vérin Ref Qty 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 2 2 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 Part No. ■ 6510 ■ 667624 ■ 667625 414352 ◆ 558200 ▲ 2716 ▲◆557478 602580 ▲ 2785 ▲ 615128 668016 ▲ 638243 ▲ 662448 ▲ 636853 668031 414353 667626 L772363 Description Bezeichnung Description Cotter pin Locking cap Nut Shell Piston O-Ring Seal O-Ring plug O-Ring Back-up ring Retainer Back-up ring Seal Wiper Nut Rod Washer Splint Sicherungskappe Mutter Zylinderrohr Kolben O-Ring Dichtung O-Ring Stopfen O-Ring Stutzring Zylinderdeckel Stutzring Dichtung Abstreifer Mutter Kolbenstange Unterlegscheibe Goupille fendue Dispositif de verrouillage Ecrou Corps de vérin Piston Joint torique Joint Bouchon à joint torique Joint torique Joint de protection Bague de retenue Joint de protection Joint Racleur Ecrou Tige de vérin Rondelle ▲ Included in service kit / Enthalten im Dichtsatz / Inclus dans le kit de service 668021 ◆ Enthalten im Kolbensatz 558255 / Included in piston kit 558255 / Inclus dans le kit de piston558255 ■ Included in cylinder nut service kit 668926 (2 kits required per cylinder ) / Enthalten im Wartungssatz der Zylindermutter 668926 (2 Wartungssätze benötigt pro Zylinder) / Inclus dans le kit de service des écrous du vérin 668926 ( 2 kits requis par vérin ) 35D Fork Positioner 10 Cascade Parts Manual Arm carrier group Armträger Gruppe Groupe coulisses 1 CL0306a.eps Qty Part No. (ref.1) Description Bezeichnung Description 4 772297 Arm carrier Armträger Coulisse Note : 4 arm bars required per clamp Achtung : 4 Armträger benötigt pro Klammer A noter : 4 coulisse requises par pince 35D Fork Positioner 11 Cascade Parts Manual Fork group Gabelgruppe Groupe fourches 6202471 6202473 1 7 4 3 2 5 6 CL0143K.eps Ref Qty Part No. 1 2 3 4 5 6 7 2 24 12 12 1 1 1 2 6202466 7659574 767961 787398 6202467 6202468 772332 665595 35D Fork Positioner Description Bezeichnung Description Pad secutex Capscrew Capscrew M8x16 Washer M8 Fork, LH Fork, RH Special wrench Warning decal Secutex Platte Kopfschraube Kopfschraube M8x16 Unterlegscheibe M8 Gabel, L Gabel, R Spezialschlüssel Warnungsschild Plateau secutex Vis à tête Vis à tête M8x16 Rondelle M8 Fourche, G Fourche, D Clé spéciale Auto collant 12 Cascade Parts Manual Lower Hook Group Bolt-On Class 2 Aufhängunsgruppe Klasse 2 Groupe Accrochage Class 2 Ref Qty Part No. 1 2 3 2 4 4 675968 667225 763024 35D Fork Positioner L783518 Description Bezeichnung Description Hook Lockwasher Capscrew Haken Unterlegscheibe Kopfschraube Crochet Rondelle Vis à tête 13 Cascade Parts Manual