owner`s manual
Transcription
owner`s manual
OWNER’S MANUAL OM-823 029 899X 2015−02 RHC-3, RHC-3GD34A, And RHC-14 Remote Hand Controls DANGER! − Indicates a hazardous situation which, if not avoided, will result in death or serious injury. The possible hazards are shown in the adjoining symbols or explained in the text. Wear safety glasses with side shields. Porter des lunettes de sécurité avec écrans latéraux. Fsafe8 2013-10 DANGER ! - Indique une situation dangereuse qui, si elle n’est pas évitée, entraînera la mort ou des blessures graves. Les éventuels risques sont représentés par les symboles joints ou expliqués dans le texte. Fsafe1 2013-10 Indicates a hazardous situation which, if not avoided, could result in death or serious injury. The possible hazards are shown in the adjoining symbols or explained in the text. Indique une situation dangereuse qui, si elle n’est pas évitée, entraînera la mort ou des blessures graves. Les éventuels risques sont représentés par les symboles joints ou expliqués dans le texte. Fsafe2 2013-10 NOTICE NOTE Indicates statements not related to personal injury. Signale des consignes non associées aux dommages corporels. Indicates special instructions. Fournit des instructions spéciales. Fsafe3 2013-10 Arc rays can burn eyes and skin − wear a welding helmet with correct filter, and cover exposed skin with nonflammable clothing. Le rayonnement de l’arc peut provoquer des brûlures au niveau des yeux ou de la peau – porter un casque protecteur muni d’un écran de filtre approprié et porter des vêtements non inflammables pour protéger toutes parties exposées. Fsafe11 2013-10 Welding sparks can cause fire or explosion. Move flammables away. Do not weld on closed tanks or barrels, or on containers that have held combustibles − they can explode. Clean tanks or barrels properly. Les étincelles de soudure peuvent provoquer un incendie ou une explosion. Ne pas souder de cuves ou de tonneaux, au risque qu’ils explosent. Nettoyer soigneusement les cuves ou tonneaux. Fsafe9 2013-10 Beware of electric shock from welding electrode or wiring. Touching the electrode while in contact with the work or ground can cause electric shock. Always wear dry gloves. Keep all panels and covers closed. Breathing welding fumes and gases can harm your health. Welding requires good ventilation. If ventilation is impossible, such as when welding in a confined space, use an air-supplied respirator. Attention au risque d’électrocution due au contact avec l’électrode de soudage ou les fils. Le fait de toucher l’électrode tout en étant en contact avec la pièce ou la terre peut provoquer une électrocution. Toujours porter des gants secs. Tous les panneaux et couvercles doivent rester fermés. L’inhalation des fumées et des gaz de soudure peut être dangereuse pour la santé. Une bonne ventilation est nécessaire pour procéder au soudage. S’il est impossible de ventiler, dans des lieux confinés par exemple, utiliser un respirateur à alimentation d’air. Fsafe10 2013-10 Fsafe6 2013-10 CALIFORNIA PROPOSITION 65 WARNINGS PROPOSITION CALIFORIENNE 65 AVERTISSEMENTS Welding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some cases, cancer. (California Health & Safety Code Section 25249.5 et seq.) This product contains chemicals, including lead, known to the state of California to cause cancer, birth defects, or other reproductive harm. Wash hands after use. Les équipements de soudage et de coupage produisent des fumées et des gaz qui contiennent des produits chimiques dont l’État de Californie reconnaît qu’ils provoquent des malformations congénitales et, dans certains cas, des cancers. (Code de santé et de sécurité de Californie, chapitre 25249.5 et suivants) Ce produit contient des produits chimiques, notamment du plomb, dont l’État de Californie reconnaît qu’ils provoquent des cancers, des malformations congénitales ou d’autres problèmes de procréation. Se laver les mains après utilisation. Fsafe4 2013-10 © 2015 MILLER Electric Mfg. Co. 1. Specifications And Connections A C B C B 7-1/2 in. (191 mm) 9-1/2 in. (241 mm) 8-3/4 in. (222 mm) 1 A 2 2. 1 Twistlock Plug 2 5- Or 14-Pin Amphenol Plug Units are equipped with a 20 ft (6 m) cord. If a longer cord is required, see Section 2. 141 127-A Selecting Interconnecting Cord Conductor Size (*AWG) Cord Length Amperage Or Voltage Control Up to 20 ft (6 m) No. 16 Up to 20 ft (6 m) (GD Models) No. 14 21 to 100 ft (6 to 30 m) (GD Models) No. 12 21 to 50 ft (6 to 15 m) No. 14 51 to 100 ft (16 to 31 m) No. 12 101 to 200 ft (31 to 61 m) No. 10 *AWG − American Wire Gauge OM-823 Page 2 RHC-14 No. 18 For Any Length 3. Adjusting Amperage Or Voltage . On some welding power sources, the front panel output control setting does not matter and the Remote Hand Control adjusts the full range of the welding power source output. Example Of Remote Amperage Control Without Output (Contactor) Control Min (40 A) Set Switch Set Control Max (200 A) Adjust Remote Amperage In Example: Min = 40 A In Range B, Max = 200 A In Range B Output = 120 A (50% of 40 to 200) Example Of Remote Amperage Control With Output (Contactor) Control Min (5 A) Max (200 A) In Example: Min = 5 A Max = 200 A Output = 200 A (100% of 5 to 200) Set Switches Set Control Place switch in On position for open-circuit voltage. When switch is in Off position no output is present. Ref. 122 023-A / Ref. 141 127-A / 039 411-D / Ref. 159 059 / Ref. 130 214-A OM-823 Page 3 4. ! Routine Maintenance Turn Off all power before maintaining. 3 Months Everyday Replace Unreadable Labels Replace Cracked Parts Move Control From Min. To Max. Cord(s) 5. Troubleshooting Trouble No amperage or voltage control. Remedy Set switches and controls on welding power source or generator (see Section 3*). Check weld output on welding power source or generator. Secure cord connections or replace cords, if necessary. No output (contactor) control. Remote Hand Control switch in wrong position or control not so equipped. Check switch settings and weld output on welding power source or generator. Secure cord connections or replace cords, if necessary. *See welding power source or generator Owner’s Manual. 6. Circuit Diagrams 150 670-C RHC-3 094 231-B RHC-3-GD34A 210 458-B RHC-3 (100 ft) OM-823 Page 4 053 656-A RHC-14 7. Parts List Item No. Dia. Mkgs. Part No. Quantity Model RHC- RHC- RHC-3 RHC-3 RHC-14 3 14 GD34A (100ft) (100ft) Description Figure 7-1. Complete Assembly . . . 1 . . . . R1 . . . . . 222 736 . . Rheostat, WW 150W 15 Ohm . . . . . . . . . 1 . . . . . . . . . . . . . . . . . . 1 . . . 1 . . . . R1 . . . . . 198 087 . . Potentiometer, CP Std Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1T 2. W 1K Linear W/Fricttabs . . . . . . . . . . . . . . . 1 . . . . . . . . . . . . . . . . . . 1 . . . 1 . . . . R1 . . . . . 605 960 . . Rheostat, WW 300W 34 Ohm . . . . . . . . . . . . . . . . . . . . . . . 1 . . . 2 . . . . . . . . . . . . . 085 220 . . Label, Caution Electric Circuit . . . . . . . . . 1 . . . . 1 . . . . 1 . . . . 1 . . . . . 1 . . . 3 . . . . . . . . . . . . +021 475 . . Wrapper . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . . . . . . . . 1 . . . . 1 . . . 3 . . . . . . . . . . . . +014 417 . . Wrapper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . . . . . . . . . . . . . . . 1 . . . 4 . . . . . . . . . . . . . 217 193 . . Case Section, Base/Front/Rear . . . . . . . 1 . . . . . . . . . . . 1 . . . 4 . . . . . . . . . . . . . 109 974 . . Case Section, Base/Front/Rear . . . . . . . . . . . . . . 1 . . . . . . . . . . . . . . . . . . 1 . . . 4 . . . . . . . . . . . . . 234 522 . . Case Section, Base/Front/Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . 5 . . . PLG1 . . . 605 797 . . Plug, Twlk 3P3W 20A 125V . . . . . . . . . . . 1 . . . . . . . . . . . . . . . . . . 1 . . . 5 . . . PLG1 . . . 144 310 . . Housing Plug & Pins, (Consisting Of) . . . . . . . . . 1 . . . . . . . . . . . . . . . . . . 1 . . . . . . . . . . . . . . . . . . . 134 732 . . . . Terminal, Male 1 Pin 24-20 Wire . . . . . . . . . . . . 14 . . . . . . . . . . . . . . . . . 14 . . . . . . . . . . . . . . . . . . . 143 922 . . . . Clamp, Cable Strain Relief Sz 17 & 20 . . . . . . . 1 . . . . . . . . . . . . . . . . . . 1 . . . 5 . . . PLG1 . . . 032 898 . . Plug, Twlk Grd 2P3W 15A 125V . . . . . . . . . . . . . . . . . . . . . 1 . . . 6 . . . . . . . . . . . . . 217 029 . . Bushing, Strain Relief . . . . . . . . . . . . . . . . 1 . . . . . . . . . . . 1 . . . . 1 . . . . . . . . . . . . . . . . . . . 217 030 . . Nut, Locking Strain Relief 1/2 In Npt .270 1 . . . . . . . . . . . 1 . . . . 1 . . . 7 . . . . . . . . . . . . . 204 213 . . Cable, Pwr 16Ga 3/C (Order By Ft) . . . . 1 . . . 7 . . . . . . . . . . . . . 270 796 . . Cable, Port No. 20 5/C (Order By Ft) . . . . . . . . . . 20Ft . . . . . . . . . . . . . . 100Ft . . . 7 . . . . . . . . . . . . . 600 349 . . Cable, Port No.14 3/C (Order By Ft) . . . . . . . . . . . . . . . . 20Ft . . . 7 . . . . . . . . . . . . . 600 795 . . Cable, Port No.12 3/C (Order By Ft) . . . . . . . . . . . . . . . . . . . . . . 100Ft . . . 8 . . . . . . . . . . . . . 186 019 . . Label, Model/Stock Number . . . . . . . . . . 1 . . . 8 . . . . . . . . . . . . . 210 459 . . Label, Model/Stock Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . 9 . . . . . . . . . . . . . 097 926 . . Knob, Pointer . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . . . . . . . . . . . . . . . 1 . . . 9 . . . . . . . . . . . . . 193 919 . . Knob, Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . . . . . . . . . . . . . . . 1 . . . 9 . . . . . . . . . . . . . 148 723 . . Knob, Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . 10 . . . . . . . . . . . . . 148 719 . . Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . . . . . . . . . . . . . . . 1 . . . 10 . . . . . . . . . . . . . 130 214 . . Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . . . . . . . . . . . . . . . 1 . . . 10 . . . . . . . . . . . . . 148 717 . . Nameplate, Rhc-3Gd 34A . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . . . . . . . S1 . . . . . . 011 609 . . Switch, Tgl SPDT 15A 125VAC . . . . . . . . . . . . . . 1 . . . . . . . . . . . . . . . . . . 1 3 1 2 10 4 9 8 7 6 5 141 128-A Figure 7-1. Complete Assembly (RHC-3 Illustrated) +When ordering a component originally displaying a precautionary label, the label should also be ordered. BE SURE TO PROVIDE MODEL AND STYLE NUMBER WHEN ORDERING REPLACEMENT PARTS. OM-823 Page 5