PUSH START Parts required
Transcription
PUSH START Parts required
Page 1 / 5 Rev.20130131 GUIDE # 3155 ADDENDUM - SUGGESTED WIRING CONFIGURATION SCHÉMA DE BRANCHEMENT SUGGÉRÉ FORTE PUSH START KIA Forte 2011-2013 At Push-to-start button Au bouton Push-to-Start At Parking Light Harness Au Harnais des lumières de stationnement (+) Start/Stop 2 Orange/Black Copyright © 2010, Fortin Auto Radio Inc Copyright © 2010, Fortin Auto Radio Inc (-) Parking Light Orange PDM Back of fuse box PDM Dos boîte fusibles (+) Start/Stop White/Orange KeyPort (+) 12V White At Brake Switch Au commutateur de frein (+) Foot Brake Blanc (+) Ignition Red (+) 12 Volts Red Harnais Right of Push to Start Button Au harnais à droite du bouton démarrage CAN High White CAN Low Black OBDII CAN HIGH Black 6 14 CAN LOW White Copyright © 2010, Fortin Auto Radio Inc HARDWARE VERSION HARDWARE VERSION : 3 FIRMWARE VERSION : 4.0+ Date: xx-xx EVO VERSION DU MATÉRIEL FIRMWARE VERSION VERSION DU LOGICIEL INTERFACE MODULE PATENTS PENDING US: 2007-228827-A1 Made in Canada www.fortinbypass.com Service No : 000 102 04 2536 Minimum 3 Minimum 4.17 Parts required (Not included) 1x 5Amp Fuse 3x 1Amp Diode (-) Key Sense Orange Copyright © 2010, Fortin Auto Radio Inc This manual may change without notice. www.ifar.ca for latest version. Ce Guide peut faire l'objet de changement sans préavis. www.ifar.ca pour la récente version. Pièce(s) requise(s) (Non incluse(s)) 1x fusible 5Amp Replace the Remote-Starter fuse with a 5A (MAX) 3x Diodes 1Amp Changez la fusible du démarreur a distance par une fusible 5A (MAX) 5A MAX NOTE The vehicles OEM remote will not be operable during remote start. La télécommande d'origine du véhicule ne sera pas fonctionnelle durant le démarrage à distance. This Guide may change without notice. www.ifar.ca for latest version. Ce Guide peut faire l’objet de changement sans préavis. www.ifar.ca pour la récente version. Page32/ /45 Page DESCRIPTION | DESCRIPTION LED | DEL Blue | Bleu Yellow | Jaune Red | Rouge 2 PIN CONNECTOR: TB CONTROL (WHITE | BLANC) 4 PIN CONNECTOR: DATA-LINK (BLACK | NOIR) Red | Rouge Black | Noir Blue | Bleu White | Blanc 12V Battery (+) | 12V Batterie (+) Ground (-) | Masse (-) DATA DATA 20 PIN CONNECTOR: MAIN HARNESS | HARNAIS PRINCIPAL (WHITE|BLANC) Black | Noir Foot Brake | Frein (pied) Signal Pink | Rose Tachometer Yellow/Black | Jaune/Noir Trunk Release | Valise Hand Brake | Frein à Main Signal Brown/White | Brun/Blanc Hood Status | Capot Statuts Pink/Black | Rose/Noir See configuration Purple/Yellow | Mauve/Jaune Green/White | Vert/Blanc See configuration Green/Red | Vert/Rouge See configuration White/Black | Blanc/Noir See configuration Lt. Blue | Bleu Pâle See configuration 1 2 13 3 12 14 4 5 16 6 17 7 18 8 15 20 9 10 5 4 3 2 1 Copyright © 2012, FORTIN AUTO RADIO INC TOUS DROITS RÉSERVÉS KIA RIO - PUSH-TO-START VEHICLES EQUIPPED WITH AN OEM ALARM Some vehicles must be UNLOCKED to disarm the OEM alarm before remote start. Enable option #12 using the FlashLink Manager. When this option is enabled the module will automatically UNLOCK before remote start and LOCK after the vehicle has remote started. A Yellow | Jaune See configuration Purple | Mauve Lock | Verrouille Purple/White | Mauve/Blanc Unlock | Déverrouille Door Status | Statuts Portes Green | Vert White | Blanc Trunk Status | Statuts Valise Orange AUX 1 Orange/Black | Orange/Noir AUX 2 Dk. Blue | Bleu foncé GWR (Ground While Running) Red/Blue | Rouge/Bleu See configuration Lt. Blue/Black | Bleu Pâle/Noir See configuration 11 19 E B 5 PIN CONNECTOR: CAN-BUS (WHITE | BLANC) Brown | Brun CAN 1 WIRE (SW) Gray/Black | Gris/Noir CAN 2 LOW Gray | Gris CAN 2 HIGH Orange/Brown | Orange/Brun CAN 1 LOW Orange/Green | Orange/Vert CAN 1 HIGH C 6 PIN CONNECTOR: RELAY | RELAIS (RED | ROUGE) White/Red | Blanc/Rouge COMM2 6 White/Blue | Blanc/Bleu NO2 5 White/Green | Blanc/Vert NC2 4 Yellow/Red | Jaune/Rouge COMM1 3 Yellow/Blue | Jaune/Bleu NO1 2 Yellow/Green | Jaune/Vert NC1 1 D VÉHICULES ÉQUIPPÉS D'UNE ALARME D'ORIGINE Certains véhicules doivent être DÉVERROUILLÉS avant le démarrage à distance pour désarmer l'alarme d'origine. A c t i v e z l ' o p t i o n # 1 2 a v e c l e F l a s h L i n k M a n a g e r. Lorsque cette option est activée, le module déverrouille automatiquement avant le démarrage à distance et reverrouille après que le véhicule a démarré à distance. This Guide may change without notice. www.ifar.ca for latest version. Ce Guide peut faire l’objet de changement sans préavis. www.ifar.ca pour la récente version. Page33/ /45 Page KIA RIO -CONNECTION PUSH-TO-START WIRING | GUIDE DE BRANCHEMENTS OUT RS11 IN RS12 IN RS13 OUT RS14 A8 (-) WHILE RUNNING A5 A4 A3 A2 (-) (-) (-) (-) IN RS15 TRUNK STATUS IN RS16 DOOR STATUS UNLOCK/DISARM OUT RS17 OUT RS18 LOCK/ARM WITH | AVEC DATA-LINK: ALWAYS REQUIRED TOUJOURS REQUIS NOT REQUIRED WITH DATALINK NON REQUIS EN DATA-LINK START (+) A9 RS8 OUT RS7 OUT IGNITION1 (+) RS6 OUT IGNITION2 (+) RS5 OUT ACCESSORY (+) RS4 OUT HOOD (-) RS3 OUT PARKING LIGHT (-) 12V BATTERY (+) RS2 IN RS1 Ground | Masse (-) REMOTE STARTER DÉMARREUR À DISTANCE WITH | AVEC DATA-LINK: Direct connection Branchement directe Cut | Coupez Cut | Coupez WITHOUT | SANS DATA-LINK: B4 B3 Red Black Blue White Red Black 12V BATTERY Ground 1A Diode A13 (-) TRUNK RELEASE A12 (+/-) TACHOMETER A11 (+) FOOT BRAKE KIA FORTE Ground B4 B3 B2 B1 A1 Yellow Purple Purple/White Green White Orange Orange/Black (-) Ground While Running Dk. Blue (+) Start Red/Blue Lt. Blue/Black (+) Foot Brake Black (+/-) Tachometer Pink (-) Trunk Release Yellow/Black Brown/White Pink/Black Purple/Yellow Green/White Green/Red White/Black Key Sense Lt. Blue IN IN IN OUT OUT IN IN IN IN OUT OUT IN OUT OUT IN A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 HARDWARE VERSION : 3 FIRMWARE VERSION : 4.0+ Date: xx-xx EVO VERSION DU MATÉRIEL Made in Canada www.fortinbypass.com 000 102 04 2536 Minimum A FIRMWARE VERSION VERSION DU LOGICIEL INTERFACE MODULE PATENTS PENDING US: 2007-228827-A1 Service No : C5 C4 C3 C2 CC1 3 Minimum 4.17 Brown CAN 1 LOW Gray/Black Gray CAN 1 HIGH Orange/Brown CAN 2 LOW Orange/Green CAN 2 HIGH D6 White/Red White/Blue D4 White/Green D3 Yellow/Red D2 Yellow/Blue D1 Yellow/Green D D5 COMM1 NO1 NC1 COMM2 NO2 NC2 D3 D5 (+)12V RS7 (+)Brake activation 1A Diode 1A Diode D2 HARDWARE VERSION B D6 C1 C2 C3 9 with a voltmeter test the Orange wire: Avec un voltmêtre testez le fil Orange: without key sans clé with key in the fob holder located in center console avec clé dans le port de la clé situé dans la console centrale 2.6 Volt to 10 Volt Back view, White connector, Back of Push-to-Start button right of the steering column. Vue de dos, conn. Blanc, au dos du bouton Push-to-Start, à droite de la colonne de direction. Back view, White connector, At Brake Switch. Vue de dos, connecteur Blanc, Au commutateur du frein. 2 3 10 11 4 5 6 6 7 8 1415 16 12 13 14 OBDII Front view Vue de face RS2 RS3 (~) CAN High White Blanc (~) CAN Low Black Noir Twisted pair from Harness Right of Push to Start Button Paire de fils torsadés Au harnais à droite du bouton démarrage (-) Parking Lights Orange Back view, White connector - At Parking Light Switch Vue de dos, connecteur Blanc - Au commutateur des lumières de stationnement (+) Ignition Red | Rouge (+)12V Red Rouge 1 Harness Right of Push to Start Button Au harnais à droite du bouton démarrage CAN LOW (Pin14) White | Blanc (+) Brake White Blanc CAN HIGH (Pin6) Black | Noir A20 (-)Key Sense Orange White/Orange Blanc/Orange Orange/Black Orange/Noir C4 5AMP Fuse (+) 12V White Blanc Ignition Lock/Arm Unlock/Disarm Door Status Trunk Status E O ALL (+) (-) (-) (-) (-) Back view White connector PDM Fuse box | Vue de dos, Connecteur Blanc PDM Boîte à fusibles 0 Volt PUSH START Replace the Remote-Starter fuse with a 5A (MAX) Changez la fusible du démarreur a distance par une fusible 5A (MAX) 5A MAX KeyPort This Guide may change without notice. www.ifar.ca for latest version. Ce Guide peut faire l’objet de changement sans préavis. www.ifar.ca pour la récente version. Page34/ /45 Page KIA RIO - PUSH-TO-START PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION 1 2 LL EVO-A Page 4 / 4 Press and hold the programming button: Insert the 4 Pin (Data-Link) connector. Appuyez et maintenir enfoncé le bouton de programmation: Insérez le connecteur 4 pins (Data-Link). The LED will alternate between BLUE, YELLOW and RED flashes. Les DELS alternent entre un flash BLEU, JAUNE et ROUGE. Release the programming button when the LED is BLUE. Relâchez le bouton de programmation quand la DEL est BLEU. If the LED is not solid BLUE disconnect the 4 Pin connector (DataLink) and go back to beginning of step 1. | Si le DEL n'est pas BLEU solide débranchez le connecteur 4 pins (Data-Link) et allez au début de l'étape 1. LL EVO-A -ALL EVO -ALL EVO Insert the required remaining connectors: 20 pin (White), 5 pin (White), 6 pin (Red). 2 pin (White), Insérez les connecteurs requis restants: 20 pins (Blanc), 2 pins (Blanc), 5 pins (Blanc), 6 pins (Rouge) 3 Flash ACC ON Off IGN ON OFF Press the Push-to-Start button twice to turn on the ignition. (Do not press the brake pedal) Once the Blue LED starts to flash rapidly: press the Push-toStart button once to shut off the ignition. The LED will turn off. The module is now programmed. Appuyez 2 fois sur le bouton démarrage (Push-to-Start) pour allumer l'ignition. (Ne pas appuyer sur la pédale de frein) Lorsque le DEL Bleu clignote rapidement: appuyez une fois sur le bouton démarrage (Push-toStart) pour éteindre l'ignition. Le DEL s'éteint. Le module est programmé. REMOTE FONCTIONNALITÉS DÉMARREUR À DISTANCE REMOTESTARTER STARTER FUNCTIONNALITY FUNCTIONNALITY | |FONCTIONNALITÉS DUDU DÉMARREUR À DISTANCE START UNLOCK START All doors must be closed. Remote start the vehicle. Toutes les portes doivent All doors must être be fermées closed. Démarrez à Remote start distance. the vehicle. Toutes les portes doivent être fermées Démarrez à distance. UNLOCK Press the Unlock button of the remote car starter. The vehicle can now be put in to gear and driven. Appuyez sur le bouton Déverrouillage de Entrez dans le véhicule avec Vous êtes maintenant vehicle can now et be Press Unlock button the remoteà car Enter the vehicle (Access with the The prêt la the télécommande duofdémarreur la clé intelligente à embrayer put in to gear and starter or distance. the OEM remote. Intelligent Access Key) sur vousKey. prendre la route. driven. Appuyez sur le bouton Déverrouillage de Entrez dans le véhicule avec Vous êtes maintenant If the vehicle is not unlocked the module will shut down remote- et prêtthe à embrayer la télécommande la clé intelligente (Access OFF du démarreur à starter and the vehicle as soon any door is opened. prendre la route. distance or de la télécommande d'origine. Key)as sur vous Si le véhicule n'est pas déverrouillé le module va éteindre le démarreur à distance et le véhicule à l'ouverture de l'une des portes. OFF Enter the vehicle with the Intelligent Access Key. If the vehicle is not unlocked the module will shut down the remotestarter and the vehicle as soon as any door is opened. Si le véhicule n'est pas déverrouillé le module va éteindre le démarreur à distance et le véhicule à l'ouverture de l'une des portes. Page 5 / 5 HARDWARE VERSION FIRMWARE VERSION Date: xx-xx EVO-ALL INTERFACE MODULE PATENTS PENDING US: 2007-228827-A1 Made in Canada Service No : Notice: Updated Firmware and Installation Guides Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product. www.fortinbypass.com 000 102 04 2536 Module label | Étiquette sur le module Notice: Mise à jour microprogramme et Guides d’installations Des mises à jour du Firmware (microprogramme) et des guides d’installation sont mis en ligne régulièrement. Vérifiez que vous avez bien la dernière version logiciel et le dernier guide d’installation avant l’installation de ce produit. WARNING The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version. MISE EN GARDE L’information de ce guide est fournie sur la base de représentation (telle quelle) sans aucune garantie de précision et d’exactitude. Il est de la seule responsabilité de l’installateur de vérifier tous les fils et circuit avant défectuer les connections. Seule une sonde logique ou un multimètre digital doivent être utilisés. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité de l’exactitude de l’information fournie. L’installation (dans chaque cas) est la responsabilité de l’installateur effectuant le travail. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité suite à l’installation, que celle-ci soit bonne ou mauvaise ou de n’importe autre type. Ni le manufacturier, ni le distributeur ne se considèrent responsables des dommages causés ou ayant pu être causés, indirectement ou directement, par ce module, excepté le remplacement de ce module en cas de défectuosité de fabrication. Ce module doit être installé par un technicien qualifié. L’information fournie dans ce guide est une suggestion. Ce guide d’instruction peut faire l’objet de changement sans préavis. Consultez le www.fortinbypass.com pour voir la plus récente version. Copyright © 2006-2012, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING TECH SUPPORT Tél: 514-255-HELP (4357) 1-877-336-7797 ADDENDUM GUIDE www.fortinbypass.com WEB UPDATE | MISE À JOUR INTERNET