Customer Drawing

N:\SolidWorks\Customer\cp5040-10cd.slddrw
Last Saved: sthomas on 29 May 2003 09:11:57
4
3
DRAWING
A1 INSTALLATION
5
6
IF THIS DOCUMENT IS PRINTED IN HARDCOPY,
IT IS FOR INFORMATION USE ONLY AND THEREFORE
IS NOT SUBJECT TO UPDATING CONTROLS. ALWAYS
REFER TO SOLIDWORKS VIEWER FOR LATEST ISSUE
7
FIRST ANGLE
PROJECTION
8
9
10
12
11
13
14
15
THIS DRAWING IS CONFIDENTIAL AND IS SUPPLIED ON THE EXPRESS CONDITION THAT
IT SHALL NOT BE LOANED OR COPIED OR DISCLOSED TO ANY OTHER PERSON OR USED
FOR ANY OTHER PURPOSE WITHOUT THE WRITTEN CONSENT OF AP RACING LTD.
GENERAL DESCRIPTION
118.40
MIN TO REMOVE PADS
L
ALL CALIPERS ARE FITTED WITH STAINLESS
STEEL FLUID BRIDGE PIPES.
TOP OF DISC &
PAD MATERIAL
38.10 (1.50")
TRAILING
38.10 (1.50")
LEADING
25.30
53.05
DI
SC
94.43
OU
TS
ID
E
13/05/03 FIRST ISSUE
B3649
RA
DIU
S 'N
'
US
DI
A
R
DI
AM
ET
ER
L
SAT
K
J
AP RACING TECHNICAL SECTION WILL
BE PLEASED TO ADVISE ON THE MOST
SUITABLE EQUIPMENT FOR ANY
PARTICULAR APPLICATION.
'
'R6
H
CALIPER PART NUMBERS
CP5040-10S4 - R.H TRAILING (BEHIND AXLE)
CP5040-11S4 - L.H TRAILING (BEHIND AXLE)
CP5040-12S4 - R.H LEADING (IN FRONT OF AXLE)
CP5040-13S4 - L.H LEADING (IN FRONT OF AXLE)
W1 MAX
G
Alterations
Particulars
DIMENSION 'PL' :TOP OF PAD MATERIAL
TO MOUNTING HOLE
BOSS FACE WITH PAD
SITTING DOWN ON LEDGE.
DIMENSION 'C' : OFFSET - DISC CENTRE
LINE TO MOUNTING HOLE
CTR
DIMENSION 'D' : MOUNTING HOLE CENTRES
DIMENSION 'H' : MOUNTING HOLE DIAMETER
DIMENSION 'U' : WHEEL CENTRE TO CALIPER
MOUNTING HOLE BOSS FACE
(DISC Ø/2) - 'PL' DIMENSION
DISC ROTATION
W2 MAX
Date & No.
M
e-mail: [email protected]
Web site: HTTP://www.apracing.com
BODY MATERIAL: ALUMINIUM ALLOY
HYDRAULIC THREADS: M10 x 1.0
PISTON MATERIAL: ALUMINIUM ALLOY
(STANDARD)
J
DISC & CALIPER TOLERANCES
TO BE SUCH THAT DISC IS CENTRAL
TO CALIPER TO WITHIN ±0.5mm
1
PISTON
DIAMETERS: 4 x 38.10 (1.500")
K
H
Tel: +44 024 7663 9595
Fax: +44 024 7663 9559
THIS CALIPER IS DESIGNED TO OPERATE
ON A SOLID OR VENTILATED DISC OF
EITHER Ø295.0 (11.60") OR Ø280.0 (11.0")
117.00
Issue
No.
117.00
16
© AP Racing Ltd. 2003
AP Racing
Wheler Road
Coventry
CV3 4LB
Initials
M
2
Zone
1
W3 MAX
W5 MAX
G
W5 MAX
DIM'N 'D'
MTG HOLE CENTRES
BLEED SCREW TIGHTENING
TORQUE 17.0Nm (12.5 Lbs/ft)
F
INLET PORT
M10 x 1.0 x 9
MIN THR'D
RADIUS 3 MAX
E
DIM'N 'C'
OFFSET
EFFECTIVE RADIUS
RADIUS 1 MIN
RADIUS 4 MAX
D
W4 MIN
RADIUS 2 MIN
E
RADIUS 5 MAX
DIM'N 'H'
MTG HOLES
F
D
111.50
DISC & WHEEL CL
RADIAL PROFILE CHART
C
DISC Ø
EFF RAD
Ø 295.0 (11.6") 122.15
Ø 280.0 (11.0") 114.65
RAD 1
97.00
89.50
RAD 2
99.00
91.50
RAD 3
141.75
134.25
RAD 4
148.00
140.50
RAD 5
165.75
158.25
C
W1
W2
W3
W4
W5
67.00
65.00
63.50
45.00
42.00
44.14
CP504010/11/12/13
B
CALIPER ASSY STROKE NUMBERS
FAMILY No.
RHT LHT RHL LHL
CP5040-
10
11
12
13
DISC
DISC DIM'N
DIM'N
DIM'N 'H'
DIM'N 'D'
RAD 'N'
DIA
WIDTH
'C'
'PL'
295.00
10.25 MAX 130.05 MAX
25.40 43.20
53.00 150.00
280.00
10.15 MIN 129.95 MIN
REMARKS
SCALE 1:1
PAD RETAINING BOLTS SHOULD BE
THIGHTENED TO A TORQUE OF 13.1Nm
(9.70 Lbs/ft(
DRAWN
APPROVED
TITLE
CP3345 PAD FAMILY
A
4 x 1.50" CALIPER
INSTALLATION DRAWING
A
ALTERNATIVE PAD - CP2340 (REDUCED AREA)
2
3
4
B
DERIVED FROM
PAD AREA
43.47 cm²
PAD VOLUME
50.12 cm³
(FIGURES FOR FULL DEPTH PAD)
1
SHEET 1 OF 1
Steve Thomas
5
6
7
8
9
10
11
12
13
DRG NO.
14
cp5040-10cd
15
16