Legrand 84527 - Copy from http://84115.free
Transcription
Legrand 84527 - Copy from http://84115.free
Sagane™ Inter centralisé de volet 845 27 Caractéristiques Tension Fréquence 100 - 240 V± 50 - 60 Hz 2 x 2,5 mm2 Profondeur = mini. 40 mm Norme Courant porteur EN 50065 IEC 60669-2-1 - 5°C à + 45°C Branchement N L A la première mise sous tension l’appui sur les touches Montée - Stop - Descente commande l’ensemble des points d’ouvrants (volet roulant ou store) de l’installation “In One by Legrand”. L’appui sur Learn(1) annule cette fonction de commande générale. (1) Touche de programmation ou apprentissage. N0064FL3/ 02 Configuration d’usine Description Voyant LEARN Médias de communication PLC => Courant porteur IR => Infrarouge N d'identification Cellule Infrarouge Touches de commandes Touche LEARN Fonctionnement L’inter centralisé de volet peut commander simultanément à partir de ses touches Montée - Stop - Descente un ensemble de produits (acteurs) qui lui sont associés lors de l’apprentissage(1), il est alors Leader du scénario(2). L’inter centralisé de volet est toujours le point central de commande (Leader) d’un scénario. Il possède une interface pour les signaux infrarouges qui permet la commande de ses scénarios et /ou d’autres produits de l’installation. Il possède deux entrées auxiliaires E1 et E2 qui peuvent être reliés à un interrupteur horaire,... (privilégier les références 846 33 et 744 25) : - L’apparition de la tension sur E1 lance le scénario qui est enregistré sur la touche de commande Montée. - L’apparition de la tension sur E2 lance le scénario qui est enregistré sur la touche de commande Descente. Attention : Privilégier un câblage inférieur à 5 mètres entre les entrées auxiliaires du produit (E1, E2) et l’interrupteur horaire. La touche de commande Stop n’est pas accessible à partir des entrées auxiliaires E1 et E2. (1) Apprentissage : action d’associer des produits en vue de les commander simultanément à partir d’un point central. Cette association se réalise en appliquant la procédure d’apprentissage du scénario en page 3. (2) Scénario : correspond à l’ensemble des produits (acteurs) qui sont associés à une touche de commande. 2 Apprentissage du scénario Etape 1 : débuter l'apprentissage (sur le LEADER) Appuyer sur LEARN Appuyer sur la touche de commande qui doit piloter le scénario Etape 2 : ajouter un acteur au scénario (sur l'ACTEUR) Pour ajouter plusieurs produits au scénario,répéter pour chaque acteur les opérations et . Appuyer sur la touche de commande qui doit être associé au leader Appuyer sur LEARN Etape 3 : enregistrer le scénario (sur le LEADER) Les voyants de tous les produits s'éteignent. Le scénario est enregistré. Appuyer sur LEARN Modification d’un scénario Etape 1 : ouvrir le scénario (sur le LEADER) Appuyer sur LEARN Les voyants de tous les produits du scénario clignotent. Appuyer sur la touche de commande qui pilote le scénario Etape 2 : modifier l'état d'un acteur du scénario (sur l'ACTEUR) Appuyer sur LEARN ou Appuyer sur LEARN Appuyer sur la touche de commande que l'on souhaite associer Pour supprimer le produit du scénario passer à l'étape 3 Etape 3 : enregistrer le scénario (sur le LEADER) Les voyants de tous les produits s'éteignent. Le scénario est enregistré. Appuyer sur LEARN Effacement d’un scénario Effacer tous les scénarios liés à la touche de commande (sur le LEADER) Appuyer sur LEARN Le scénario est effacé Appuyer sur la touche de commande et maintenir 10s 5s Effacer tous les scénarios liés à ce produit (sur le LEADER) Appuyer sur LEARN Retour du produit en configuration usine Appuyer sur LEARN et maintenir 10s 5s Légende Le voyant s'éteint Le voyant clignote lentement Le voyant clignote rapidement 3 Le voyant flashe Sagane™ Centrale rolluikschakelaar 845 27 Eigenschappen Spanning Frequentie 100 - 240 V± Diepte = mini. 40 mm Norm 50 - 60 Hz 2 x 2,5 mm2 Draaggolf EN 50065 IEC 60669-2-1 - 5°C tot + 45°C Aansluiting N L Standaardconfiguratie Bij de eerste inschakeling worden bij een druk op de toetsen Omhoog – Stop – Omlaag alle openingspunten (rolluik of jaloezie) van de installatie “In One by Legrand” bediend. 5 Beschrijving Controlelampje LEARN Communicatiemiddelen PLC => Draaggolf IR => Infrarood Identificatienummer Infraroodcel Bedieningstoetsen Toets LEARN Werking De centrale rolluikschakelaar inter voor luiken kan tegelijkertijd met behulp van de toetsen Omhoog – Stop – Omlaag productverzamelingen (actoren) bedienen die hier aan toegevoegd zijn tijdens het aanleren(1), het is dan de Leider van het scenario(2). Opmerking: alleen de toets ON hoeft ingelezen te worden, de toets OFF wordt automatisch ingelezen. Hij bezit een interface voor infrarode signalen waarmee zijn scenario’s en/of andere producten van de installatie bediend kunnen worden. Hij bezit twee hulpingangen E1 en E2 die aan kunnen worden verbonden. (Gebruik referentienummers 846 33 en 744 25). - Door het verschijnen van spanning op E1 wordt het scenario gelanceerd dat op de bedieningstoets Omhoog geregistreerd is. - Door het verschijnen van spanning op E2 wordt het scenario gelanceerd dat op de bedieningstoets Omlaag geregistreerd is. Let op : Gebruik een kabel korter dan 5 meter tussen de extra ingangen van het product (E1, E2) en de tijdschakelaar. De bedieningstoets Stop is niet toegankelijk vanuit de hulpingangen E1 en E2. (1) Aanleren : actie van het associëren van producten met de bedoeling deze tegelijkertijd vanaf een centraal punt te bedienen. Dit associëren geschiedt door toepassing van de aanleerprocedure van het scenario op pagina 7. (2) Scenario: komt overeen met alle producten (actoren) die bij een bedieningstoets horen. 6 Aanleren van het scenario Stap 1: beginnen met aanleren (op de LEIDER) Druk op LEARN Druk op de bedieningstoets die het scenario bestuurt Stap 2: voeg een actor toe aan het scenario (op de ACTOR) Herhaal voor het toevoegen van meerdere producten aan het scenario voor iedere actor Druk op de bedieningstoets die aan de leider moet zijn toegevoegd Druk op LEARN de handelingen en . Stap 3: het scenario registreren (op de LEIDER) De controlelampjes van alle producten gaan uit. Het scenario is geregistreerd. Druk op LEARN Wijziging van een scenario Stap 1: het scenario openen (op de LEIDER) Druk op LEARN De controlelampjes van alle producten van het scenario knipperen. Druk op de bedieningstoets die het scenario bestuurt Stap 2: de staat van een actor van het scenario wijzigen (op de ACTOR) Druk op LEARN Druk op LEARN Druk op de bedieningstoets die u toe wilt voegen of Ga voor het wissen van het product uit het scenario naar stap 3 Stap 3: het scenario registreren (op de LEIDER) De controlelampjes van alle producten gaan uit. Het scenario is geregistreerd Druk op LEARN Wissen van een scenario Wis alle scenario's die verbonden zijn met de bedieningstoets (op de LEIDER) Druk op LEARN Het scenario is gewist Druk op de 5s bedieningstoets en houd deze 10 s ingedrukt Wis alle scenario's die bij dit product horen (op de LEIDER) Druk op LEARN Legende Druk op LEARN en houd deze 10 s ingedrukt 5s Het controlelampje gaat uit Het controlelampje knippert langzaam Het controlelampje knippert snel Het controlelampje flitst 7 Terugkeer van het product naar de standaardconfiguratie Sagane™ General shutter controller 845 27 Characteristics Voltage Frequency 100 - 240 V± Depth = 40 mm min. Standard 50 - 60 Hz 2 x 2,5 mm2 EN 50065 Power line carrier IEC 60669-2-1 - 5°C to + 45°C Connection N L Factory configuration The first time it is switched on, pressing the Up - Stop - Down keys controls all opening points (roller shutters or awnings) in the “In One by Legrand” installation. Pressing Learn(1) cancels this general control function. (1) Programming or learn key. 9 Description LEARN indicator lamp Communication media PLC => Mains-borne signalling IR => Infrared ID number Infrared cell Command keys LEARN key Operation The general shutter controller Using its Up - Stop - Down keys it can simultaneously control a set of products (actors) that have been associated with it during the learn phase(1). It is then the Leader of the scenario(2). The general shutter controller is always the central control point (Leader) of a scenario. It has two auxiliary inputs, E1 and E2, which can be connected to a time switch, etc (preferably use Cat. Nos 846 33 and 744 25) : - The appearance of voltage on E1 starts the scenario which is recorded on the Up control key. - The appearance of voltage on E2 starts the scenario which is recorded on the Down control key. Caution : Preferably less than 5 meters of cabling between the product’s auxiliary inputs (E1, E2) and the time switch. The Stop control key cannot be accessed from auxiliary inputs E1 and E2. (1) Learn phase: Operation to associate products so that they can be controlled simultaneously from a central point. This association is carried out by applying the learn scenario procedure on page 11. (2) Scenario: Corresponds to the set of products (actors) that are associated with a command key. 10 Learn scenario Step 1: Start the learn phase (on the LEADER) Press LEARN Press the command key that is to control the scenario Step 2: Add an actor to the scenario (on the ACTOR) To add a number of products to the scenario, repeat operations and for each actor. Press the command key that is to be associated with the leader Press LEARN Step 3: Record the scenario (on the LEADER) The indicator lamps of all the products go off. The scenario is recorded. Press LEARN Modification of a scenario Step 1: Open the scenario (on the LEADER) Press LEARN The indicator lamps of all the products in the scenario blink. Press the command key that controls the scenario Step 2 : Modify the state of an actor in the scenario (on the ACTOR) Press LEARN Press LEARN Press the command key that is to be associated or To remove the product from the scenario, go to step 3 Step 3 : Record the scenario (on the LEADER) The indicator lamps of all the products go off. The scenario is recorded. Press LEARN Clearing a scenario Clear all the scenarios linked with the command key (on the LEADER) Press LEARN The scenario is cleared Press the command key and hold it down for 10 s 5s Clear all the scenarios linked to this product (on the LEADER) Press LEARN Return the product to factory configuration Press LEARN and hold down for 10 s 5s Key The indicator lamp goes off The indicator lamp blinks slowly The indicator lamp blinks quickly 11 The indicator lamp flashes