Gesamt-Kjeldahl-Stickstoff, TKN Probenvorbereitung LCW 909
Transcription
Gesamt-Kjeldahl-Stickstoff, TKN Probenvorbereitung LCW 909
PA 909 - 06/7 Probenvorbereitung Seite 1 LCW 909 Programmieranleitung CADAS 100 ≥ LPG 210 Gesamt-Kjeldahl-Stickstoff, TKN Ausgabe 97/06 Achtung! Das Ausgabedatum dieser Programmieranleitung muß mit dem Ausgabedatum der Arbeitsvorschrift der Reagenzien identisch sein. Nur so ist gewährleistet, daß Sie die korrekten Daten in Ihr Gerät einprogrammieren. Hinweis! Sollten Sie während der Programmierung einen Fehler machen, können Sie die letzte Eingabe durch Drücken der Taste ➞ auf der Tastatur rückgängig machen. bezeichnen die rechte und linke ➞ und L ➞ ➞ Die Eingabezeichen R Taste. Programmierung von LCW 909 Gesamt-Kjeldahl-Stickstoff, TKN Meßbereich I ● Programm VAR (Variation eines Testes) anwählen. ● Taste unter Symbol »909 A« anwählen. Gesamt-Kjeldahl-Stickstoff, TKN Display-Anzeige Symbol: Eingabe 909 A Name: KJELDAHL-N-1 LCW 909 Pro: 1 3 STA FPRG Taste unter 1 anwählen λ = 694 nm W: Faktor: 2 1 = 21.50 Konstante: 0.000 Einheit: mg/l Meßbereichsgrenzen: ja untere Grenze: 1 mg/l obere Grenze: 10 mg/l nein Taste unter ja anwählen Programmierung von LCW 909 Gesamt-Kjeldahl-Stickstoff, TKN Meßbereich II ● Programm VAR (Variation eines Testes) anwählen. ● Taste unter Symbol »909 B« anwählen. Gesamt-Kjeldahl-Stickstoff, TKN Display-Anzeige Eingabe Symbol: 909 B Name: KJELDAHL-N-2 LCW 909 Pro: 1 W: λ = 694 nm Faktor: 1 2 = Konstante: 3 STA FPRG Taste unter 1 anwählen 107.5 0.000 Einheit: mg/l Meßbereichsgrenzen: ja nein untere Grenze: 10 mg/l obere Grenze: 200 mg/l Taste unter ja anwählen Die komplette Dateneingabe wird auf dem Drucker dokumentiert. Die vollständige Übernahme in den Speicher wird durch den Ausdruck »gespeichert« bestätigt. Bitte vergleichen Sie den Ausdruck nochmals mit den einzugebenden Daten. PA 909 - 06/7 Probenvorbereitung Seite 2 LCW 909 Programmieranleitung CADAS 100 ≥ LPG 210 Gesamt-Kjeldahl-Stickstoff, TKN Ausgabe 97/06 Achtung! Das Ausgabedatum dieser Programmieranleitung muß mit dem Ausgabedatum der Arbeitsvorschrift der Reagenzien identisch sein. Nur so ist gewährleistet, daß Sie die korrekten Daten in Ihr Gerät einprogrammieren. Hinweis! Sollten Sie während der Programmierung einen Fehler machen, können Sie die letzte Eingabe durch Drücken der Taste ➞ auf der Tastatur rückgängig machen. bezeichnen die rechte und linke ➞ und L ➞ ➞ Die Eingabezeichen R Taste. Programmierung von LCW 909 Gesamt-Kjeldahl-Stickstoff, TKN Meßbereich III ● Programm VAR (Variation eines Testes) anwählen. ● Taste unter Symbol »909 C« anwählen. Gesamt-Kjeldahl-Stickstoff, TKN Display-Anzeige Symbol: Eingabe 909 C Name: KJELDAHL-N-3 LCW 909 Pro: 1 3 STA FPRG Taste unter 1 anwählen λ = 694 nm W: Faktor: 2 1 = 1075 Konstante: 0.000 Einheit: mg/l Meßbereichsgrenzen: ja untere Grenze: 200 mg/l obere Grenze: 2000 mg/l nein Taste unter ja anwählen Die komplette Dateneingabe wird auf dem Drucker dokumentiert. Die vollständige Übernahme in den Speicher wird durch den Ausdruck »gespeichert« bestätigt. Bitte vergleichen Sie den Ausdruck nochmals mit den einzugebenden Daten. PA 909 - 06/7 Programming instructions CADAS 100 ≥ LPG 210 Sample Preparation Page 1 LCW 909 Total Kjeldahl Nitrogen, TKN Edition 97/06 Attention! The edition date of this programming instruction must be identical to the edition date of the intruction attached to the reagents. This is the only way to ensure that your instrument will be programmed with the correct data. Please note! If you make an error during programming, you can cancel the last entry by pressing the key ➞ on the keyboard. indicate the right and left ➞ and L ➞ ➞ The input symbols R keys respectively. Programming of LCW 909 Total Kjeldahl Nitrogen, TKN Measuring range I P Select the program VAR (variation of a test). ● Select function key below symbol »909 A«. Total Kjeldahl Nitrogen, TKN Display Input via keyboard Symbol: 909 A Name: KJELDAHL-N-1 LCW 909 Pro: 1 3 STA FPRG Press function key below 1 λ = 694 nm W: Factor: 2 1 = 21.50 Constant: 0.000 Unit: mg/l Measuring limit: yes Lower limit: 1 mg/l Upper limit: 10 mg/l no Press function key below yes Programming of LCW 909 Total Kjeldahl Nitrogen, TKN Measuring range II P Select the program VAR (variation of a test). ● Select function key below symbol »909 B«. Total Kjeldahl Nitrogen, TKN Display Input via keyboard Symbol: 909 B Name: KJELDAHL-N-2 LCW 909 Pro: 1 3 STA FPRG Press function key below 1 λ = 694 nm W: Factor: 2 1 = 107.5 Constant: 0.000 Unit: mg/l Measuring limit: yes Lower limit: 10 mg/l Upper limit: 200 mg/l no Press function key below yes All data entries are documented on the printer; their transfer to storage is confirmed by the printer message »stored«. You should check the printed data to ensure that all entries are correct. PA 909 - 06/7 Programming instructions CADAS 100 ≥ LPG 210 Sample Preparation Page 2 LCW 909 Total Kjeldahl Nitrogen, TKN Edition 97/06 Attention! The edition date of this programming instruction must be identical to the edition date of the intruction attached to the reagents. This is the only way to ensure that your instrument will be programmed with the correct data. Please note! If you make an error during programming, you can cancel the last entry by pressing the key ➞ on the keyboard. indicate the right and left ➞ and L ➞ ➞ The input symbols R keys respectively. Programming of LCW 909 Total Kjeldahl Nitrogen, TKN Measuring range III P Select the program VAR (variation of a test). ● Select function key below symbol »909 C«. Total Kjeldahl Nitrogen, TKN Display Input via keyboard Symbol: 909 C Name: KJELDAHL-N-3 LCW 909 Pro: 1 3 STA FPRG Press function key below 1 λ = 694 nm W: Factor: 2 1 = 1075 Constant: 0.000 Unit: mg/l Measuring limit: yes Lower limit: 200 mg/l Upper limit: 2000 mg/l no Press function key below yes All data entries are documented on the printer; their transfer to storage is confirmed by the printer message »stored«. You should check the printed data to ensure that all entries are correct. PA 909 - 06/7 Instruction de programmation CADAS 100 ≥ LPG 210 Préparation d’échantillon Page 1 LCW 909 Azote Total Kjeldahl, TKN Edition 97/06 Attention! La date d’édition de ces instructions doit être identique à celle du mode d’emploi des réactifs. Dans ce cas seulement, vous êtes assurés d’entrer les bonnes données dans votre appareil. Conseil! En cas d’erreur durant la programmation, vous pouvez revenir sur la dernière entrée en utilisant la touche ➞ sur le clavier. servent de touche droite et gauche ➞ et L ➞ ➞ Les touches d’édition R . Programmation du LCW 909 Azote Total Kjeldahl, TKN Gamme de mesure I P Sélectionner le programme VAR (pour modifier un test). ● Choisir le symbole »909 A«. Azote Total Kjeldahl, TKN Display Commande sur le clavier Symbole: 909 A Nom: KJELDAHL-N-1 LCW 909 Pro: 1 3 STA PRGL Appuyer la touche sous 1 λ = 694 nm W: Facteur: 1 2 = 21.50 Constante: 0.000 Unité: mg/l Limites de mesure: oui Limite inférieure: 1 mg/l Limite supérieure: 10 mg/l non Appuyer la touche sous oui Programmation du LCW 909 Azote Total Kjeldahl, TKN Gamme de mesure II P Sélectionner le programme VAR (pour modifier un test). ● Choisir le symbole »909 B«. Azote Total Kjeldahl, TKN Display Commande sur le clavier Symbole: 909 B Nom: KJELDAHL-N-2 LCW 909 Pro: 1 3 STA PRGL Appuyer la touche sous 1 λ = 694 nm W: Facteur: 1 2 = 107.5 Constante: 0.000 Unité: mg/l Limites de mesure: oui Limite inférieure: 10 mg/l Limite supérieure: 200 mg/l non Appuyer la touche sous oui L’ensemble des données est imprimé. Le transfert complet des données dans la mémoire est confirmé par le message »mémorisé«. Vérifiez que les données imprimées corresspondent bien à celles que vous avez entrées. PA 909 - 06/7 Instruction de programmation CADAS 100 ≥ LPG 210 Préparation d’échantillon Page 2 LCW 909 Azote Total Kjeldahl, TKN Edition 97/06 Attention! La date d’édition de ces instructions doit être identique à celle du mode d’emploi des réactifs. Dans ce cas seulement, vous êtes assurés d’entrer les bonnes données dans votre appareil. Conseil! En cas d’erreur durant la programmation, vous pouvez revenir sur la dernière entrée en utilisant la touche ➞ sur le clavier. servent de touche droite et gauche ➞ et L ➞ ➞ Les touches d’édition R . Programmation du LCW 909 Azote Total Kjeldahl, TKN Gamme de mesure III P Sélectionner le programme VAR (pour modifier un test). ● Choisir le symbole »909 C«. Azote Total Kjeldahl, TKN Display Commande sur le clavier Symbole: 909 C Nom: KJELDAHL-N-3 LCW 909 Pro: 1 3 STA PRGL Appuyer la touche sous 1 λ = 694 nm W: Facteur: 1 2 = 1075 Constante: 0.000 Unité: mg/l Limites de mesure: oui Limite inférieure: 200 mg/l Limite supérieure: 2000 mg/l non Appuyer la touche sous oui L’ensemble des données est imprimé. Le transfert complet des données dans la mémoire est confirmé par le message »mémorisé«. Vérifiez que les données imprimées corresspondent bien à celles que vous avez entrées.