SUZUKI GSXR 600/750 Oggy Knob Kit

OGGY KNOBBS AUSTRALIA™ by PROMOTO
PART NO. OK 750/751
SUZUKI GSXR 600
1997-2000 V/W/X/Y
GSXR 750 1996-1999 T/V/W/X
SUZUKI GSXR 600
2004-2005 K4/K5
GSXR 750 2004-2005 K4/K5
SUZUKI GSXR 1000 2003-2004 K3/K4
(Note –the five above applications require fairing no modifications to fit.)
OGGY KNOBB KIT
OGGY KNOBB KIT
OGGY KNOBB KIT
SUZUKI GSXR 600
2001-2003 K1/K2/K3 GSXR 750 2000-2003 Y/K1/K2/K3
OGGY KNOBB KIT
SUZUKI GSXR 1000 2001-2002 K1/K2
OGGY KNOBB KIT
(Note –the three above applications require fairing modification on Left Hand Side.)
Congratulations on purchasing your Oggy Knobb kit. It has been designed to reduce damage to your motorcycle from impact and abrasion by the
road surface in an accident. We have used only the highest quality materials to achieve the strength and appearance your investment deserves.
Carefully read the fitting instructions below and check you kit contents before starting installation. If you are unsure or not confident about installing
Oggy Knobbs yourself, see your mechanic.
GSXR 600 1997-2000
GSXR 750 1996-1999
GSXR 600 2004-2005
GSXR 750 2004-2005
GSXR 1000 2003-2004
Instructions-first five applications as shown in photos above:
Tools required:
8mm Hex Key.
1.
2.
3.
4.
Remove the engine mounting bolt, the position of which can be seen from the photos above.
Fit the Oggy Knobb assembly with the aluminium spacer behind the Oggy Knobb, making sure the spacer fits
inside the recess in the frame. The spacers and Oggy Knobbs are stamped L and R to avoid confusion.
Tighten the bolt securely to manufacturer’s specifications. Use of a thread-locking agent is recommended.
On the other side, repeat steps 1 to 3.
Note: Always use the supplied washers under bolt heads. Always use thread-locking compound.
OGGY KNOBBS AUSTRALIA™ by PROMOTO
PART NO. OK 750/751
GSXR 600 2001-2003 LHS
GSXR 750 2000-2003 LHS
GSXR 1000 2001-2002 LHS
GSXR 600 2001-2003 RHS
GSXR 750 2000-2003 RHS
GSXR 1000 2001-2002 RHS
Instructions-second three applications as shown in photos above-Left Hand Side:
Tools required:
3mm, 4mm and 8mm Hex Keys, Sharp Knife or Holesaw or Die Grinder & Drill to cut plastic.
1.
2.
3.
4.
5.
Remove the fairing panel and engine mounting bolt, the position of which can be seen in the photo above.
Fit the Oggy Knobb assembly with the aluminium spacer behind the Oggy Knobb, making sure the spacer
fits inside the recess in the frame. The spacers and Oggy Knobbs are stamped L and R to avoid confusion.
Tighten the bolt securely to manufacturer’s specifications. Use of a thread-locking agent is recommended.
Offer up the fairing panel and mark a circle where the Oggy Knobb assembly touches. Cut the fairing panel
to clear the Oggy Knobb assembly and refit the fairing panel. Refer to white circle in top left photo as an
approximate guide.
On the right hand side, repeat steps 1 to 3 noting that there is no need to remove or modify the fairing panel.
Note: Always use the supplied washers under bolt heads. Always use thread-locking compound.