interactive chase-a-lite panel 18535
Transcription
interactive chase-a-lite panel 18535
Page 1 of 3 Copyright ROMPA® Ltd INTERACTIVE CHASE-A-LITE PANEL 18535 ABOUT THIS PRODUCT The objective is to press a button when it is illuminated. This will produce a fanfare and all of the buttons will light up. Using the panel controls, the volume can be adjusted. The pattern and speed can also be changed. Tip: For those will visual limitations or who are easily distracted, this activity would be best placed in a Snoezelen® room where other competing stimuli can be removed or reduced. This helps the participant to focus without having to engage selective attention. This activity can be made more challenging by increasing the level of distraction in the room. For example, including a competing stimuli such as sound / music. CONTENTS 1 x Chase-A-Lite Panel TO WALL MOUNT PANEL IMPORTANT: This panel weighs approximately 23 kg. Please take this into consideration when fixing. Please make sure that you are aware of the construction of the wall the panel is to be fixed to. Taking this into account please ensure that you use the correct fittings. For example, walls may be partition walls and plaster board as opposed to solid brick or stone walls. Take advice from a suitably qualified professional builder or from an estates department if in any doubt about appropriate fixtures. Consider proximity to a wall plug socket when deciding where to wall mount your Panel. Attach fixings such as mirror plates to the back of the panel. Fixings are not supplied as these depend on the surface the panel will be fixed to. Check the fixings e.g. mirror plates you buy can easily support 23kg. You may wish to attach two mirror plates to the back of the panel at the top and two on the back at the bottom. Note: When attaching fixings to the back of the panel please proceed with caution – be aware that there are electrical assemblies inside the panel. OPERATION Plug in. Aim to strike one of the push buttons when it is illuminated. This produces a fanfare and all the lights flash. MAINTENANCE Unplug. Remove the panel from the wall. Lay the panel on its back and remove the plastic front cover. To change the lamp: each lamp holder is attached to a micro switch inserted into the threaded rear of each push button. Remove the lamp holder and micro switch together by easing and pulling firmly. Remove the faulty lamp and replace with a new lamp of the same specification (24V 3W capless). To change the fuse: the only fuse is in the plug (UK only). INTERACTIVE CHASE-A-LITE PANEL 18535, SW 5.08 Page 2 of 3 Copyright ROMPA® Ltd SAFETY For indoor use only. Handle with care. Always supervise the use of this product. In the unlikely event of product failure please seek advice – only a suitably qualified person should attempt repair. SPECIFICATION 240V / 110V INTERACTIVE CHASE-A-LITE PANEL 18535, SW 5.08 Page 3 of 3 Copyright ROMPA® Ltd PANNEAU CHAINE MUSICALE INTERACTIVE 18535 EN CE CONCERNE CE PRODUIT Le but est de pousser le bouton illuminé. Si on arrive à le faire on entend une fanfare et on voit clignoter toutes les lumières. En réglant les boutons de contrôle on peut régler le volume, la direction et la vitesse. CONTENU 1 x Chase-A-Lite Panel POUR ATTACHER CE PANNEAU AU MUR IMPORTANT: Ce panneau pèse vers 23 kilos. Prenez cette information en considération quand vous fixez le collier au mur. Tenez compte de la construction du mur sur lequel vous allez fixer le collier. Tout bien considérez quand vous achetez des installations. Par exemple, le mur pourrait être une cloison, de Placoplâtre® ou un mur solide en brique. En cas de doute en ce qui concerne les installations, cherchez les conseils d’un maçon convenablement qualifié ou votre service de maintien. Attachez des installations à l’arrière du panneau et puis utilisez les installations pour fixer le panneau au mur. Les installations ne sont pas comprises – elles dépendent la construction de votre mur et devraient supporter 23 kilos sans risque. On pourrait utiliser par exemple les plaques – deux à l’arrière en haut et deux autres à l’arrière en bas. Notez : En attachant des installations à l’arrière du panneau, prenez soin – tenez compte des parties électriques à l’intérieur du panneau. FONCTIONNEMENT Branchez. Le but est de pousser le bouton illuminé. Si on arrive à le faire on entend une fanfare et on voit clignoter les lumières. ENTRETIEN Débranchez. Détachez le panneau du mur. Mettez le panneau sur une surface plate. Desserrez le devant et l’enlevez. Pour changer la lampe : À l’arrière de chaque bouton il y a un support de lampe attaché à un micro-contacteur. Enlevez le support de lampe et le micro-contacteur à la fois, en les tirant fermement. Enlevez et remplacez la lampe usée : 12V 3W sans bouchon Pour changer le fusible : la seule fusible est dans la prise britannique. SURETE Pour l’usage à l’intérieur seulement. Maniez ce produit avec soin. Il faut toujours surveiller l’usage de ce produit. En cas peu probable de panne, cherchez des conseils – seulement un adulte convenablement qualifié devrait essayer réparer ce produit. CARACTERISTIQUES TECHNIQUES 240V / 110V INTERACTIVE CHASE-A-LITE PANEL 18535, SW 5.08