microscoop 100 e - nvp

MICROSCOOP 100 E
L - 04E S - A
2000 - 12 - 14
1/4
DOC 010
2320
42°
1500
1290
1320
1030
600
220
835
1760
1525
1430
5030
1050
1000
36°
2100
1840
2075
3375
Capacities
Weights
Tramming capacity ...................................1 000 kg (2 200 lb)
Breakout force, lift..................... 10.7 kN - 1 094 kg (2 407 lb)
Breakout force, tilt..................... 36.9 kN - 3 766 kg (8 285 lb)
Tipping load .................................................4 551 (10 012 lb)
Bucket std. ............................. 0.54 m³ ( 0.7 yd³), 500 BNH lip
Operating weight.......................................3 640 kg (8 000 lb)
Total loaded weight.................................4 640 kg (10 200 lb)
Axle weights without load
front axle ................................................700 kg (1 540 lb)
rear axle ..............................................2 940 kg (6 460 lb)
Axle weights with load
front axle .............................................2 280 kg (5 010 lb)
rear axle ..............................................2 360 kg (5 190 lb)
Bucket motion times
Raising time ............................................................... 3.0 sec.
Lowering time ............................................................ 1.5 sec.
Tipping time ............................................................... 4.5 sec.
Driving speeds forward and reverse (loaded)
50 Hz.................................................. 0 to 8 kph (0 to 5 mph)
60 Hz............................................ 0 to 8.8 kph (0 to 5.5 mph)
SANDVIK TAMROCK SECOMA se reserve le droit de modifier sans préavis les caractéristiques techniques de cette notice.
aprod1200
Microscoop 100 E
Spec. no: L - 04E S - A
2000 - 12 - 14
2/4
Service capacities
Buckets hydraulics
Hydraulic oil tank........................................ 62 litre (16.4 gal.)
Hydrostatic transmission oil tank.................. 31 litre (8.2 gal.)
Full hydraulic open center system with one pump.
Oil flows to bucket hydraulic system from the steering pump,
when steering is not used.
Equipped with mechanical dual control lever.
Engine
Drive motor........... Three-phase, asynchronous, squirrelcage
Output ...................................................... 30 kW (40 hp total)
Voltage .......................................................................... 380 V
Frequency ..................................................................... 50 Hz
Speed..................................................................... 1 500 rpm
Insulation class..................................................................... F
Degree of protection....................................................... IP 55
Transmission
Transmission................................... Hydrostatic transmission
variable flow, fully reversible
Pump................................................. Linde, 0 to 50 cm³ / rev
Motor ................................................ Linde, fixed 35 cm³ / rev
Transfer case
Type ............................................................................... Gear
Location...................................................................Rear axle
Axles
Front and rear .................................................Tamrock, fixed
No-spin in front axle
Central hinge oscillating ...................................................± 7°
Wheels
Tyres ................................................................. 7.50 x 15, L5
Air pressure, front & rear............................ 350 kPa (3.5 bar)
Main components:
Control valve....................................Commercial hydraulics
Lift cylinder (1) ................................ø 100/60 mm, Tamrock
Tilt cylinder (1) ................................ø 120/60 mm, Tamrock
Fittings ............................................................................JIC
Pressure settings:
Main relief valve.................................... 14.0 MPa (140 bar)
Bucket tilt .................................................. 6.0 MPa (60 bar)
Bucket roll-back .................................... 18.0 MPa (180 bar)
Boom raise ........................................... 18.0 MPa (180 bar)
Boom lower............................................... 6.0 MPa (60 bar)
Frame
Rear and front frame ..................... Welded steel construction
Material.........................................................................E 36.3
Central hinge ............................................ Spherical bearings
(large angle)
Electrical equipment
Cable
Cable reel ......................................Automatic tension control,
end of cable safety
Secondary electric sysrem ................................. 24 V AC/DC
Lights....................................................... 2 pcs in front, 70 W
2 pcs in rear, 70 W
Steering..............................................2 hydraulic cylinders
Steering control .........................Frame steering, control lever
Articulation angle............................................................ ± 36°
Main components:
Hydraulic pump ...................................................... Denison
Control valve .......................................................... Danfoss
Steering cylinders (2) ............... ø 60 mm (2.36´´), Tamrock
Pressure settings:
Main relief valve ................................... 14.0 MPa (170 bar)
Port relief valves................................... 17.5 MPa (175 bar)
Service Brake ........................... Hydrostatic transmission
Actuation ....................................................................... Pedal
Optional equipment
Bucket width 950 mm (37 ´´), 0.5 m³ (0.7 yd³).
Other voltage or frequency.
Electric motors for tropical conditions.
FOPS-ROPS canopy.
Back up alarm.
Emergency steering system.
Spare rim and tyre (Xmine D2).
Radio remote control.
Gate end box.
Parking and Emergency Brakes
Type ................................................... Hydraulic oil immersed
multiple disc brakes inclosed in the rear axle
Actuation ................................................... Emergency button
Spring applied, hydraulically released
SANDVIK TAMROCK SECOMA se réserve le droit de modifier sans préavis les caractéristiques
techniques de cette notice.
SANDVIK TAMROCK SECOMA S.A., B.P. 46 - 69881 Meyzieu Cedex, France
Tel. int. + 33 4 72 45 22 00, Telex 300526 F
Telefax int. + 33 4 7831 7980
MICROSCOOP 100 E
L - 04E S - A
DOC 010
= 30 kW / 50 Hz
= 30 kW / 60 Hz
SPEED (km/h)
0
10
20
30
40
50
60
0
1
2
3
4
5
GRADEABILITY & SPEED
6
7
8
9
2000 - 12 - 14
3/4
GRADE (%)
SANDVIK TAMROCK SECOMA se reserve le droit de modifier sans préavis les caractéristiques techniques de cette notice.
aprod1200
SANDVIK TAMROCK SECOMA se réserve le droit de modifier sans préavis les caractéristiques
techniques de cette notice.
0
10
20
30
40
50
60
0
50
100
200
250
Slope / Grade
Loaded speed (kph)
Empty speed (kph)
300
0%
20 %
ONE WAY DISTANCE IN METRES
150
1 000 kg
8 km/h
0.5 min.
3%
350
Hor./0
8.0
8.0
400
1:5/20
7.0
8.0
Fixed cycle time includes the time for filling, dumping,
turning and accelerating
Payload
Overall speed limit
Fixed cycle time
Rolling resistance
Basic data for calculations :
PRODUCTIVITY CURVE
450
Microscoop 100 E
Spec. no: L - 04E S - A
2000 - 12 - 14
4/4
SANDVIK TAMROCK SECOMA S.A., B.P. 46 - 69881 Meyzieu Cedex, France
Tel. int. + 33 4 72 45 22 00, Telex 300526 F
Telefax int. + 33 4 7831 7980
TONNES PER HOUR