Publications C Versèle
Transcription
Publications C Versèle
1 Publications comme auteur 1.1 Chapitres de livres et articles de revues avec comité de lecture [1] C. Versèle, O. Deblecker et J. Lobry, « Identification de paramètres et contrôle vectoriel en temps-réel d’un moteur asynchrone dans l’environnement Matlab/Simulink/dSPACE », Journal sur l’enseignement des sciences et technologies de l’information et des systèmes, J3eA, Vol. 8, N° Hors Série 1, Edition Spéciale CETSIS 2008, http://www.j3ea.org, 2009. [2] C. Versèle, O. Deblecker, G. Bury and J. Lobry, « Implementation of advanced control schemes using dSPACE material for teaching induction motor drive », International Journal of Electrical Engineering Education, IJEEE, Manchester University Press, Vol. 47, No. 2, pp. 151-167, April 2010. [3] C. Versèle, O. Deblecker and J. Lobry, « Multiobjective optimal design of medium frequency transformers for full-bridge DC-DC converter », International Review of Electrical Engineering, IREE, Vol. 5, No. 4, pp. 1354-1363, July-Augustus 2010. [4] C. Versèle, O. Deblecker and J. Lobry, « A decision-making aid tool dedicated to the design of auxiliary railway power supplies », European Journal of Electrical Engineering, EJEE, Vol. 14, No. 4, pp. 421-450, September 2011. [5] C. Versèle, O. Deblecker and J. Lobry, « Multiobjective optimal design of an inverter fed axial flux permanent magnet in-wheel motor for electric vehicle », Chapitre 12 du livre Electric Vehicles – Modelling and Simulations, édité par S. Soylu, InTech Publication, ISBN 978-973-307-477-1, pp. 287-308, 2011. [6] C. Versèle, O. Deblecker and J. Lobry, « Implementation of induction motor drive control schemes in Matlab/Simulink/dSPACE environment for educational purpose », Chapitre 15 du livre Matlab for Engineers – Applications in Control, Electrical Engineering, IT and Robotics, édité par K. Perukta, InTech Publication, ISBN 978-953-307-1077-0, pp. 365-386, 2011. [7] C. Versèle, O. Deblecker and J. Lobry, « A computer-Aided Design Tool Dedicated to Isolated DC-DC Converters Based on Multiobjective Optimization Using Genetic Algorithms », The International Journal for Computation and Mathematics in Electrical and Electronic Engineering, COMPEL (accepted – to be published in 2012). [8] C. Versèle, O. Deblecker et J. Lobry, « A response Surface Methodology Approach to Study the Influence of Specifications or Model Parameters on the Multiobjective Optimal Design of Isolated DC-DC Converters », IEEE Transactions on Power Electronics, (accepted – to be published in 2012). 1.2 Actes de conférences avec comité de lecture [1] C. Versèle, O. Deblecker and J. Lobry, « Implementation of a vector control scheme using dSPACE Material for Teaching Induction Motor Drive and Parameters 1 Identification », 2008 International Conference on Electrical Machines, ICEM 2008, publication IEEExplore, Vilamoura, Portugal, 6-9 September 2008. [2] C. Versèle, O. Deblecker and J. Lobry, « Identification de paramètres et contrôle vectoriel en temps-réel d’un moteur asynchrone dans l’environnement Matlab/Simulink, dSPACE », 7éme Colloque sur l’Enseignement des Technologies et des Sciences de l’Information et des Systèmes, CETSIS 2008, Bruxelles, Belgique, 27-29 octobre 2008. [3] C. Versèle, O. Deblecker and J. Lobry, « Multiobjective Optimal Design of High Frequency Transformers Using Genetic Algorithm », 13th European Conference on Power Electronics and Applications, EPE 2009, publication IEEExplore, Barcelona, Spain, 8-10 September 2009. [4] C. Versèle, Z. De Grève, F. Vallée, R. Hanuise, O. Deblecker, M. Delhaye and J. Lobry, « Analytical Design of an Axial Flux Permanent Magnet In-Wheel Synchronous Motor for Electric Vehicle », 13th European Conference on Power Electronics and Applications, EPE 2009, publication IEEExplore, Barcelona, Spain, 8-10 September 2009. [5] C. Versèle, O. Deblecker and J. Lobry, « Dimensionnement optimal par algorithmes génétiques de l’inductance couplée d’un convertisseur DC-DC de type Flyback », Électrotechnique du Futur 2009, EF’09, Compiègne, France, 24-25 septembre 2009. [6] C. Versèle, O. Deblecker and J. Lobry, « Multiobjective Optimal Design of a Full-Bridge dc-dc Converter Using Genetic Algorithms », 5th IEEE Young Researchers Symposium in Electrical Power Engineering, Leuven, Belgium, 29-30 March 2010. [7] C. Versèle, O. Deblecker and J. Lobry, « Multiobjective Optimal Design of Transformers for Isolated Switch Mode Power Supplies », 20th International Symposium on Power Electronics, Electrical Drives, Automotion and Motion, SPEEDAM 2010, publication IEEExplore, Pisa, Italy, 14-16 June 2010. [8] C. Versèle, O. Deblecker, Z. De Grève and J. Lobry, « Multiobjective Optimal Design of a Voltage Supply Inverter Fed In-Wheel Synchronous Motor », IEEE 2010 Vehicle Power and Propulsion Conference, VPPC 2010, publication IEEExplore, Lille, France, 1-3 September 2010. [9] C. Versèle, O. Deblecker and J. Lobry, « On the multiobjective optimal choice of isolated dc-dc converter topology and design using genetic algorithms », PCIM Europe 2011, Nuremberg, Germany, 17-19 May 2011. [10] C. Versèle, O. Deblecker, S. Coorevits and J. Lobry, « Rigorous choice of isolated dc-dc converter topologies using response surface method », ELECTRIMACS 2011, Cergy-Pontoise, France, 6-8 June 2011. [11] C. Versèle, O. Deblecker and J. Lobry, « Multiobjective optimal choice and design of isolated dc-dc power converters », 14th European Conference on Power Electronics 2 and Applications, EPE 2011, publication IEEExplore, Birmingham, England, 30 Augustus – 1 September 2011. [12] C. Versèle, O. Deblecker and J. Lobry, « A surface response methodology approach to study the influence of specifications in the multiobjective optimal design of power conbverters », 14th European Conference on Power Electronics and Applications, EPE 2011, publication IEEExplore, Birmingham, England, 30 Augustus – 1 September 2011. 2 Publications comme co-auteur 2.1 Articles de revues avec comité de lecture [1] Z. De Grève, C. Versèle et J. Lobry, « Etude théorique, simulation et réalisation d’un « Levitron » à l’aide du logiciel de calcul par éléments finis Comsol Multiphysics », Journal sur l’enseignement des sciences et technologies de l’information et des systèmes, J3eA, Vol. 8, N° Hors Série 1, Edition Spéciale CETSIS 2008, http://www.j3ea.org, 2009. [2] O. Deblecker, P. Bertrand and C. Versèle, « Modeling and simulation of auxiliary railway power supply without crowbar in case of catenary transient overvoltage », International Review on Modelling and Simulations, I.RE.Mo.S., Vol. 3, No. 3, June 2010. [3] Z. De Grève, C. Versèle and J. Lobry, « Gyroscopic magnetic levitation: an original design procedure based on the finite element method », The European Physical Journal Applied Physics, EPJAP, vol. 52, no. 2, October 2010. 2.2 Actes de conférences avec comité de lecture [1] Z. De Grève, C. Versèle and J. Lobry, « Etude théorique, simulation et réalisation d’un « Levitron » à l’aide du logiciel de calcul par éléments finis Comsol Multiphysics », 7éme Colloque sur l’Enseignement des Technologies et des Sciences de l’Information et des Systèmes, CETSIS 2008, Bruxelles, 27-29 octobre 2008. [2] F. Vallée, Z. De Grève, C. Versèle, O. Deblecker, M. Delhaye et J. Lobry, « Exploitation pédagogique du logiciel Labview pour le traitement d’un essai normalisé de court-circuit triphasé brusque aux bornes d’une machine synchrone à pôles saillants fonctionnant initialement à vide », 7éme Colloque sur l’Enseignement des Technologies et des Sciences de l’Information et des Systèmes, CETSIS 2008, Bruxelles, 27-29 octobre 2008. [3] Z. De Grève, C. Versèle and J. Lobry, « Using perturbation force analysis for the design of a Levitron® », COMSOL CONFERENCE 2008, Hannover, Germany, 4-7 November 2008. 3 [4] Z. De Grève, C. Versèle and J. Lobry, « Gyroscopic magnetic Levitation: an original design procedure based on the finite element method », 6ème Conférence Européenne sur les méthodes numériques en Electromagnétisme, NUMELEC 2008, Liège, Belgique, 8-10 December 2008. [5] O. Deblecker, P. Bertrand et C. Versèle, « Étude d’une chaîne de puissance auxiliaire en traction ferroviaire face à une surtension de caténaire», Électrotechnique du Futur 2009, EF’09, Compiègne, France, 24-25 septembre 2009. [6] O. Deblecker, P. Bertrand and C. Versèle, « Study of auxiliary railway power supply facing catenary transient overvoltage », 15th Annual Conference of the IEEE Industrial Electronics Society, IECON 2009, publication IEEExplore, Porto, Portugal, 3-5 November 2009. [7] F. Vallée, C. Versèle, R. Loughlimi et J. Lobry, « Prise en compte de l’indisponibilité non programmée des centrales thermiques classiques et de l’impact de l’algorithme de résolution utilisé dans un problème de minimisation des émissions de gaz polluants en présence de production décentralisée de type éolien », Électrotechnique du Futur 2011, EF’11, Belfort, France, 14-15 décembre 2011. [8] F. Vallée, C. Versèle, J. Lobry and F. Moiny, « Development of a Monte Carlo simulation tool in order to minimize polluting gases emissions in presence of wind power under cost and load covering constraints », 2012 International Conference on Renewable Energies and Power Quality, ICREPQ’12, Santiago de Compostela, Espagne, 28-30 March 2012 (accepted – to be published). 4