indash blank template 08-01
Transcription
indash blank template 08-01
I-751281004 Page 1 of 2 * * ADVISEMENT * * MOUNTING LOCATION: Lower right side of radio J BR TOOLS REQUIRED: Hook tool #20 Torx Driver HARDWARE INCLUDED: None CELL PHONE & MEDIA MOUNT INSTALLATION INSTRUCTIONS PART#:751281004 MFG: MERCEDES MODELS & YEARS: G500 2002-05 CLK-Series 2004 (Pg.1) (Pg.2) -ML-Series06-11, GL-Series07-11 Instructions for Mercedes CLK 320 & CLK 500: STEP #1: Remove shifter bezel by pulling up on the front of the bezel to release (2) clips. Pull again to release (2) more clips. Slide bezel towards dash to release back slide from console with hook tool. Pry up and out on the (2) clips to remove ashtray assembly. Lift and tilt out ashtray assembly. You may need to open the ashtray door to do this. Read instructions completely prior to starting installation. All InDash Mounts are designed so that after installation, phone is facing normal driver position for left-hand drive vehicles. This mount is not designed to be used in foreign countries with right-hand drive vehicles. Use extreme care when working around the plastic components on the dash. Excess force, can cause breakage of the plastic components. STEP #2: Remove the (2) bezel screws below the climate control with the T-20 Torx driver. With your hands pull out the bottom of the bezel (radio will not come off with bezel) and tilt up slightly. Open cup holder at the top right of the switches by the glove box. Pull out on the bezel to the right of the switches. Release bezel completely. Do Not Disconnect Wires. STEP #3: Move the bezel to be able to get at the T-20 Torx screw at the lower right of the radio. Remove the screw and place the InDash by PanaVise Mount over screw hole and replace the screw. Carefully replace the bezel in reverse order. . Showing bezel removed Instructions for Mercedes G500: STEP #1: Open ashtray door, insert hook tool into the upper right corner of the radio/ climate control/ switches bezel. Release one corner, then repeat on the left side. There are (4) clips, (2) upper clips between the radio and switches and (2) to the sides of the climate control. Release all (4) clips and pull bezel out. STEP #2: Remove lower right radio screw and place InDash by PanaVise over hole and replace the screw. Replace the bezel. INSTALLATION IS NOW COMPLETE. ENJOY YOUR NEW INDASH by PANAVISE MOUNT Prototype InDash installed Prototype installed showing location. Same on all models CLK & G500. Notice space to cup holder. 10-15-10 There may be recent updates to this Instruction Sheet, please visit our website or contact PanaVise Products, Inc. for the latest revision as well as for the most complete up-to-date PanaVise InDash Applications List: 7540 Colbert Dr., Reno, NV, Phone: 800.759.7535, 775.850.2900, Fax: 800.395.8002, www.panavise.com. © 2002 PanaVise Products, Inc. I-751281004 Page 2 of 2 * * ADVISEMENT * * MOUNTING LOCATION: Lower right side of radio J BR TOOLS REQUIRED: Hook tool #20 Torx Driver HARDWARE INCLUDED: None CELL PHONE & MEDIA MOUNT INSTALLATION INSTRUCTIONS PART#:751281004 MFG: MERCEDES MODELS & YEARS: ML-Series 06-11 GL-Series 07-11 (See Pg. 1 for G500 2002-05 CLK-Series (2004 ) STEP #1: With your hands unlatch the panel with the climate control and switches on it by pulling out from the bottom to release (2) clips. Tilt panel out and up, then angle out and down. Release the panel and set aside. Do Not disconnect any wires. STEP #2: Remove the lower (2) T-20 Torx radio screws, as they will allow the (2) radio release slide bars to be moved down. With a tool or your finger push the (2) slide bars below the radio down as far as possible. Pull the radio out from the bottom with your hands. Pull it straight out. Move radio off to the left to allow access to the lower right side of the radio screw. Remove the (1) T-20 Torx screw and place the InDash by PanaVise Mount over the screw hole and replace the screw. Read instructions completely prior to starting installation. All InDash Mounts are designed so that after installation, phone is facing normal driver position for left-hand drive vehicles. This mount is not designed to be used in foreign countries with right-hand drive vehicles. Use extreme care when working around the plastic components on the dash. Excess force, can cause breakage of the plastic components. Climate Control Panel Removal STEP #3: Replace the radio and climate control panel in reverse order. INSTALLATION IS NOW COMPLETE. ENJOY YOUR NEW INDASH by PANAVISE MOUNT Radio Removal Slide Bar InDash Mounting Screw Location Final Installation Picture 10-15-10 There may be recent updates to this Instruction Sheet, please visit our website or contact PanaVise Products, Inc. for the latest revision as well as for the most complete up-to-date PanaVise InDash Applications List: 7540 Colbert Dr., Reno, NV, Phone: 800.759.7535, 775.850.2900, Fax: 800.395.8002, www.panavise.com. © 2002 PanaVise Products, Inc.