identification - SDL Suspension
Transcription
identification - SDL Suspension
www.sdlsuspension.com IDENTIFICATION CJ TRANSMISSION -T-14, cast iron case, three speed fully-synchronized transmission, the mainshaft has 10 splines on the output end. Casting numbers on the transmission case T14X-1X or 13-02-065-9XX. Used from 1967-75 in V6 & staight 6 cylinder model CJ’s. Case length 8.68”. -T-15, cast iron case, three speed fully-synchronized transmission, the mainshaft has 6 splines on the output end. Casting numbers on the transmission case, T15A-1X or 13-07-065-9XX. Used from 1972-75 in V8 model CJ5. Case length 10”. -T-150, cast iron case, three speed fully-synchronized transmission. Casting numbers on the transmission case, 260XXXX. Used from 1976-79, 6 & 8 cylinder CJ5 & CJ7. Case length 9.18”. -T-170, aluminum case, four speed transmission. Casting numbers on the transmission case, C2604XXX. Used from 1980-84, 4-6-8 cylinder model; CJ5, CJ7 & CJ8. Case length 10.25". -SR4, aluminum case, four speed transmission. Used ball bearings on maindrive gear & mainshaft. Casting numbers on transmission case; 13-32-065-9XX or 13-40-065-9XX. The top cover has a Ford casting mark. Used from 1980-81, 4 & 6 cylinder CJ’s. Case length 9.25". -T-4, aluminum case, four speed transmission. Used tapered bearings on maindrive gear & mainshaft. Casting numbers on transmission case; 13-51-065-9XX or 13-52-065-9XX. Used from 1982-86, 4 & 6 cylinder model CJ5 & CJ7. -T-5, aluminum case, five speed transmission. Used tapered bearings on maindrive gear & mainshaft. Casting numbers on transmission case; 13-51-065-9XX or 13-52-065-9XX. Used from 1982-86, 4 & 6 cylinder model CJ5 & CJ7. YJ-TJ MANUAL TRANSMISSIONS (1987-06) AX4 AX5 BA10/5 AX15 Used in 4 cyl engines up to 10/04/88 Used in 4 cyl engines after 10/04/88 Used in 6 cyl engines 1987 up to 03/09/89 Used in 6 cyl engines after 03/03/89-99 NV3550 Used in 6 cyl engines TJ 00-06 TRANSFER CASE -Dana Spicer gear identification : all gears are stamped with 18-8-XX -Dana model 20 (72-79) has off set output shafts. The model 20 has a lower front output shaft and a upper rear output shaft. All models have single shift levers. -Dana model 300 (80-86) has off set output shafts. The model 300 has a lower front output shaft and a upper rear output shaft. The output shaft housings are aluminum. All models have single shift levers. -Borg Warner Quadratrac (76-79 CJ7 automatic only) is a chain drive transfer case. The Quadratrac was used with an automatic transmission which featured full time four wheel drive, all aluminum case. Front and rear Axle identification Dana model 35 rear axle 87-95 YJ 97-06 TJ Dana model 44 AMC model 20 rear axle rear axle 48-75 CJ 76-86 CJ 86 CJ7 97-06 TJ Dana model 25,27,30 front axle Model 25 45-64 CJ Model 27 65-71 CJ Model 30 72-86 CJ Model 30 disconnect 87-95 YJ Model 30 97-06 TJ JEEP IDENTIFICATION TJ 97-06 YJ 92-95 CJ7 76-86 YJ 86½-91 CJ5 76-83 CJ5 55-75 Note : Le cadre de vitre sur les plus vieux modèle de Jeep est interchangeable. Donc il est très important avant de commander un toit de toile de vérifier la largeur du cadre de vitre. Important lorsque vous commandez des pièces pour votre Jeep, le côté droit ou gauche est déterminé lorsque vous êtes assis sur le banc du conducteur. Note : Windshield frames are sometimes interchanged on older model Jeeps. The vehicle’s windshield and body style are the key factors that determine which convertible top fits a particular Jeep. Therefore, if unsure of your Jeep type, make sure windshield heights or widths are taken for proper identification. Remember, when ordering parts for your Jeep, the left and right of the vehicle is determined by sitting in the drivers seat. 3