Multichoice DVB S2 Migration 24 June 2013
Transcription
Multichoice DVB S2 Migration 24 June 2013
Multichoice DVB S2 Migration 24 June 2013 Multichoice will be migrating the following 3 transponders from DVB S to DVB/S2 in July: Transponder 17K - 11,554 MHz (Vertical) Transponder 16K - 11,514MHz (Horizontal) Transponder 18K - 11,554 MHz (Horizontal) The proposed date for the switch-over is set for the 1 July at 00:01. Please note, this migration will affect HDPVR decoders and action will be required in SMATV installations only (Single Cable). No Head-end settings or hardware required, the only action required, is to update 2 existing network settings in the HDPVR menu. Single decoders require no action. *No action required at domestic or Multi-switch installations. There may be a possibility that HDPVR decoders will require a re-boot, or a flash reset, if affected HD channels do not display. After the migration, the following 4 HD channels will not display until the network settings are updated: 1. 2. 3. 4. M Showcase HD M Action+ HD M Family HD M Comedy HD No pre-emptive action can be done; settings can only be changed once the migration has been effected by Multichoice. We will add updated information to our useful links section of our website http://www.spacetv.co.za/pages/useful-links.php Please keep checking for updates. If you are on facebook, like our page for current information, and updates on the run. See below for complete settings, valid after S2 Migration. This information is shared in good faith and based on information received from Multichoice. For technical reasons, this migration may be delayed by Multichoice, dates and time in this document as received on date of writing. For more information, contact us on 0861 40 41 42. Regards The Space Television Team Settings for DStv HD decoders on IF conversion systems from 2013/07/01 1. On your remote control press the [MENU] button. 2. Select [Advanced Options] and press [OK] on your remote. 3. Enter PIN 9-9-4-9. 4. Select [Network Set-up] and press [OK] on your remote. 5. Set-up Home Network with the following settings: Network LNB Power LNB Mode LNB Lo Frequency LNB Hi Frequency DStv IS7/20 13V Univ 9750 10700 6. Press [P+] to go to Additional Networks and enter the following settings: Network Signal Set-up Use NIT Frequency S.R. FEC Pol. Mod. Additional Network 1 Additional Network 2 Additional Network 3 Additional Network 4 Additional Network 5 Additional Network 6 Additional Network 7 Additional Network 8 Additional Network 9 Additional Network 10 Additional Network 11 Additional Network 12 Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled Enabled SMATV SMATV SMATV SMATV SMATV SMATV SMATV SMATV SMATV SMATV SMATV SMATV 10730 10770 10810 10850 10890 10930 11210 11250 11290 11330 11370 11410 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 30000 5/6 2/3 5/6 2/3 2/3 5/6 5/6 5/6 5/6 5/6 5/6 5/6 V V V V V V V V V V V V QPSK 8PSK QPSK 8PSK 8PSK QPSK QPSK QPSK QPSK QPSK QPSK QPSK 7. Once you have entered settings as above, press [OK] to save. 8. Select [Network Set-up] and press [OK] on your remote. 9. Press the [Yellow] button on your remote, to scan all enabled networks. Once scanning is complete, your decoder is ready to be used. www.spacetv.co.za | 0861 40 41 42 Settings for DStv SD decoders on IF conversion systems from 2013/07/01 1. On your remote control press the [MENU] button. 2. Select [Advanced Options] and press [OK] on your remote. 3. Select [Dish Installation] and press [OK] on your remote. 4. Enter PIN 9-9-4-9. 5. Enter the following settings: Network Select Use NIT Frequency S.R. FEC Pol. Home Network Network 2 Network 3 Network 4 Network 5 Network 6 Network 7 Network 8 Network 9 Network 10 Other Other Other Other Other Other Other Other Other Other Yes SMATV SMATV SMATV SMATV SMATV SMATV SMATV SMATV SMATV 11594 10730 10810 10930 11210 11250 11290 11330 11370 11410 27500 30000 30000 30000 30000 30000 30000 30000 30000 30000 5/6 5/6 5/6 5/6 5/6 5/6 5/6 5/6 5/6 5/6 V V V V V V V V V V 6. Scan All Networks Once scanning is complete, your decoder is ready to be used. www.spacetv.co.za | 0861 40 41 42