N° CE-PED-A1-ECL 01-07-THA
Transcription
N° CE-PED-A1-ECL 01-07-THA
Bureau Veritas S.A. is a Notified Body under the number 0062 Autorisation d'apposer le numéro d'identification (0062) de l'organisme notifié Bureau Veritas SA Letter of authorization to affix the Bureau Veritas SA notified body number (0062) N° CE-PED-A1-ECL 01-07-THA BUREAU VERITAS S.A., agissant dans le cadre du contrat TCKL 05 014 et de sa notification (numéro d'organisme notifié 0062) au titre du module A1 seulement de l'annexe III de la directive "Equipements sous pression" n° 97/23/CE, autorise le demandeur à apposer le numéro d'identification 0062 accompagnant le marquage CE sur les produits identifiés ci-après: BUREAU VERITAS S.A., acting within the scope of the contract TCKL 05 014 and of its notification (notified body number 0062) for module A1 only of annex III of the Pressure Equipment directive n° 97/23/EC, authorizes the applicant to affix the identification number 0062 accompanying the CE marking, on the items of equipment identified hereinafter: Fabricant (Nom) / Manufacturer (Name) : Eknavakol Co. Ltd. Adresse / Address: 39/21 Moo 7km, 8 Ram-Indhra Rd, Kannayao, Buengkum, 10230 Buengkum, THAILAND Mandataire (Nom ) / Authorized representative (Name): N/A Adresse / Address: N/A Marque commerciale / Branding name: - Description de l'équipement / Equipment description: Assembly - Monomer Mixing Tank 150 Litres Identification du type / Identification of type: Assembly as described in Annex 1. Cette autorisation est accordée / This authorization is granted : ¤ pour tous les produits du lot suivant / for all items of the batch defined as follows: Mode d'apposition et emplacement du marquage de l'équipement / Nature and location of the affixing of the marking of the equipment: Please see Annex 1. Nameplate is permanently affixed to the tank. Le marquage CE concerné par la présente lettre est destiné en priorité aux autorités de contrôle des Etats membres et non au consommateur final. La présente autorisation est présumée nulle et le fabricant supportera seul les conséquences de son utilisation, en cas de modification apportée à l'équipement susceptible de remettre en cause sa conformité aux exigences essentielles de sécurité ou à ses conditions d'utilisation prévues et, de manière générale, si le fabricant ne respecte pas, notamment, l'une ou l'autre des obligations mises à sa charge par la Directive 97/23/CE du 29 mai 1997 telle que transposée dans le(s) droit(s) national(aux) applicable(s). The CE marking referred to in this letter is first and foremost intended for the Member States surveillance authorities, and not for the final consumer. This authorisation shall be deemed to be void and the manufacturer shall alone bear any consequences pursuant to its use, in case of modification to the equipment where this may affect conformity with the essential safety requirements or the prescribed conditions for use of the equipment, and generally where the manufacturer fails in particular to comply with any of his obligations under directive nr 97/23/EC of 29 May 1997 as transposed in the applicable law(s). Etabli à / Made at Le (MM/JJ/AAAA) / On (MM/DD/YYYY) Bangkok, Thailand 07/13/2007 Signé par / Signed by Signature / Signature Raul Vieira Code d'enregistrement / Registration code: 2007/194.11,3109/P La présente attestation est soumise aux Conditions Générales de Service de Bureau Veritas jointes à la demande d'intervention signée par le demandeur. This certificate is subject to the terms of Bureau Veritas General Conditions of Service attached to the agreement signed by the applicant. Copyright Bureau Veritas - 09/2005 PV /200 1/1 + Annexe File N° : TCKL 05 014 http://www.bureauveritas.com/ped ANNEX 1 TO THE APPLICATION FORM (MODULE A1) IDENTIFICATION OF THE EQUIPMENT COVERED BY THE APPLICATION SUPPLIES (Type) - Distributor (Non-isolated) Gauge Pressure Transmitter RTD Sensor Pressure Gauge Differential Pressure Transmitter SUPPLIER (Name & Address) Yokogawa (Thailand) Ltd. 799 Rama 9 Road Bangkapi, Huaykwang Bangkoj 10310 Thailand “Watson-Marlow England” Peristaltic pump Novatech Co Ltd 36/9-10 Changwattana Road Tungsonghong, Laksi Bangkok 10210 Thailand “GEMU” Tank Bottom Valve T.V.P Valve and Pneumatic Co Ltd 7/157 Moo 11 Ram-Indra Road Kannayao Bangkok 10230 Thailand “DVP” Rotary Vacuum Pump “CKD” Solinoid Valve Flowtech Enterprise Ltd Part 96/408, Moo 7 Rama II Road Samaedam, Bangkhuntied Bangkok 10150 Thailand “Burgmann” Mechanical Seal Burgmann (Thailand) Co Ltd Bangna Tower C 12th Floor, 40/14 Moo 12 Bangna-Trad Road Bangkaew, Bangplee Samutprakarn 10540 Thailand Butterfly Valve J.S Enrich Engineering Co Ltd 27/1 Moo 8 Soi Romyen Nongbon, Pravet Bangkok 10260 Thailand “MORITEX” Light Source “MORITEX” Light Guide Imaqtronix Co Ltd 140/15 Soi Ladprao 41 Ladprao Road Chankasem, Jatujak Bangkok 10900 Thailand “Flender” Bevel Geared Motor K Power Engineering Co Ltd 7/3 Central Tower B Pinklao 15th Floor Baromrajchonee Road Bangkok-noi Bangkok 10700 Thailand “Saint-Gobain” Flexible Hose Vatska Co Ltd 81/69 Moo 4, Ratanathibeth Road Saima, Muang Nontaburi 11000 Thailand “Omron” Inductive Proximity Switch Trisak Automation Co Ltd 248 Rajchadapisek Road Huaykwang Bangkok 10320 Thailand “Nitto” Quick Connect Nandee Inter-Trade Co Ltd 314, 316, 318, 320, 322 Soi Chan 32, Chan Road Tung Wat Don, Sathorn Bangkok 10120 Thailand “Donadon SDD” Rupture Disc Donadon SDD Sri Via Gobetti 18-20019 Settimo Milanese MI Italy PLC Control Infinity Engineering System Co Ltd 56/137 Moo 7 Soi Paholyothin 56 Paholyothin Road Bangkhen Bangkok 10220 Thailand Head forming LABORATORIES * IN CHARGE OF PRODUCTION TESTING - Tension Test Bend Test Sutee Group Int Co Ltd 27/5 Moo 7 Kingkaew-Teparak Road Bangpleeyai, Bangplee Samutprakarn 10540 Thailand NAME & ADDRESS (For External Laboratory) LPN Plate Mill PCL Laboratory 199/9 Moo 4, Suksawad Road Pakklongbangplakod Prasamutjedee Samutprakarn 10290 Thailand * Laboratory in charge of the type testing / production testing (give details on an attached sheet where necessary: name and address, accreditation, recognition, scope of activities)