GTS-PP II - Canusa-CPS
Transcription
GTS-PP II - Canusa-CPS
Product Data Sheet GTS-PP II Fused 3LPP Field Applied Coating System For more than 35 years, Canusa-CPS has been a leading developer and manufacturer of specialty pipeline coatings for the sealing and corrosion protection of pipeline joints and other s u b s t ra t e s . Canusa-CPS high CANUSA -CPS performance products are manufactured to the highest quality standards and are available A-CPS S CANU in a number of configurations to accommodate many specific project applications. Product Description A key offering within the GTS-PP product family, GTS-PP II uses ShawCor's unique, and patented, cross-linked polypropylene outer layer, along with a proprietary rapid-activation polypropylene copolymer adhesive and advanced liquid epoxy layer to deliver protection that far exceeds minimum industry standards, such as ISO, while offering significant installation advantages over the highest performing PP systems, that require higher installation temperatures. Features & Benefits Lower Temperature 3LPP Coating Technology GTS-PP II provides 3LPP protection with the following components: ! ! ! Polypropylene Top Coat offering the hardness, mechanical protection and resistance to moisture absorption typically required for pipelines utilizing polypropylene coatings High Temperature Epoxy on the Steel providing proven resistance to corrosion and to cathodic disbondment while allowing for relatively low installation temperatures when compared to other systems. Rapid-Activation PP Copolymer Adhesive bonding the polypropylene top coat to the epoxy layer and fusing to the 3LPP factory-applied coating where the joint coating overlaps with the lowest possible installation temperatures. Fuses with the Lowest Installation Temperatures GTS-PP II fuses to the 3LPP factory-applied coating while requiring the lowest installation temperatures in the industry. The system can be installed directly and very efficiently by pipeline contractors in an efficient and controlled manner, using uniform induction heating technology. GTS-PP II is also available in elevated thickness and with engineered features, such as the Patented Reduced Edge Thickness Design, which promotes a completely uniform and fused system and which further minimizes installation time by reducing unneeded extra coating thickness at the overlap area. Available with Full Automation This advanced coating technology is also fully compatible with Canusa-CPS' patented innovation, the IntelliCOAT system, which automates the installation of heat shrinkable pre-extruded coating systems, such as GTS-PP II. When combined, these technologies deliver consistent in-field application and full repeatability with improved safety and can even offer significant productivity and cycle time improvements. Patented Technology GTS-PP II's cross-linked PP technology and Reduced Edge Thickness Design are patented in North America and throughout Europe and the rest of the world. Applications Oil & Gas Offshore Pipelines High Temp Girth-Weld Joints Polypropylene Configurations Wrapid Sleeve™ CanusaTube™ 3-Layer Pipe Sizes 115 - 1220 (4” - 48”) Temperature Range up to 120°C (248°F)* CANUSA-CPS is registered to ISO 9001:2008. * Actual Temperature rating is dependant on specific project requirements and conditions. Please consult your local Canusa representative. The product selection chart shown here is intended as a guide for standard products. Consult your Canusa representative for specific projects or unique applications. Below are typical values based on Heavy Duty (L-thickness) Sleeves. Sleeve Operating Characteristics Product Selection Guide Offshore / Onshore Pipeline Operating Temp. Minimum Installation Temp. Resistance to Circumferential Forces Resistance to Soil Stress Resistance to Axial Pipe Movement Main Line Coating Compatibility Celsius Fahrenheit 175º 347° 150° 302° 125º 257° 100º 212º 75º 167º 50º 122º GTS-PP II °C °C 120 170 excellent excellent excellent PP, FBE Typical Product Properties Sleeve Backing Adhesive Test Standard Unit GTS-PP II 3 0.93 > 140 > 500 > 100 3 Density Melting Point Lap Shear @ 23°C (73°F) Lap Shear @ 100°C (212°F) ASTM D792 ASTM D3418 EN 12068 EN 12068 g/cm °C N/cm2 2 N/cm Density Tensile Strength @ 23°C (73°F) Elongation at Break @ 23°C (73°F) Hardness Water Absorption @ 23°C (73°F), 24 hours Volume Resistivity Low Temperature Brittleness @ -40°C (-40°F) ASTM D792 ASTM D638 ASTM D638 ASTM D2240 ASTM D570 ASTM D257 ASTM D746 g/cm Mpa % Shore D % ohm.cm – 0.93 28 425 65 0.2 2 x 1017 pass Peel Strength @ 23°C (73°F) Peel Strength @ 100°C (212°F) Peel Strength @ 120°C (248°F) Impact Holiday Detection Indentation @ 110°C (230°F) Cathodic Disbondment @ 23°C (73°F), 28 days Cathodic Disbondment @ 120°C (248°F) 28 days Hot Water Immersion @ 95°C (203°F), 28 days NFA 49-711 NFA 49-711 NFA 49-711 NFA 49-711 NFA 49-711 DIN 30678 ASTM G8 ASTM G42* CSA N/cm N/cm N/cm J/mm kV mm mm mm Rating > 150 > 70 > 25 10 25 0.4 <3 <3 1 * ASTM G42 Test Method modified to suit testing @ 120°C (248°F) Dimensions & Ordering Info How To Order: GTS-PP II 915-450 WS BK BK - Black Colour Configuration CT - CanusaTube™, WS - Wrapid Sleeve™ Sleeve Width 450, 600mm (18", 24") & Project Specific widths available 115 - 1220 mm (4" - 48") Pipe Size Canusa P Primer (Ordered Separately) Primer Adhesive (min. thickness as supplied) 1.5 mm (60 mils) Backing (min. thickness as supplied) 1.0 mm (40mils) Product Name sleeve width Ordering Options - GTS-PP II pipe size Min. Sleeve Width = Bare Steel Dimension + 50 mm (2") on each side of the pipe joint. GTS-PP II - Low Preheat Global Transmission Sleeve for Polypropylene Pipelines www.canusacps.com Canada U.S.A./Latin America Europe/Middle East Asia/Pacific CANUSA-CPS a division of SHAWCOR LTD. 25 Bethridge Road Toronto, Ontario M9W 1M7, Canada Tel: +1 (416) 743-7111 Fax: +1 (416) 743-5927 CANUSA-CPS a division of SHAWCOR INC. 2408 Timberloch Place Building C-8 The Woodlands, Texas 77380, U.S.A. Tel: +1 (281) 367-8866 Fax: +1 (281) 367-4304 CANUSA SYSTEMS a division of SHAWCOR UK LIMITED Unit 3, Sterling Park Gatwick Road Crawley, West Sussex England RH10 9QT Tel: +44 (1293) 541254 Fax: +44 (1293) 541777 CANUSA-CPS a division of SHAWCOR INC. #05-31, Blk 52, Frontier Ubi Avenue 3 Singapore 408867 Tel: +65-6749-8918 Fax: +65-6749-8919 Canusa warrants that the product conforms to its chemical and physical description and is appropriate for the use stated on the installation guide when used in compliance with Canusa’s written instructions. Since many installation factors are beyond our control, the user shall determine the suitability of the products for the intended use and assume all risks and liabilities in connection therewith. Canusa’s liability is stated in the standard terms and conditions of sale. Canusa makes no other warranty either expressed or implied. All information contained in this installation guide is to be used as a guide and is subject to change without notice. This installation guide supersedes all previous installation guides on this product. E&OE Printed on recycled paper. Recyclable. PDS-NA-GTSPPII-rev012