USING YOUR CrystalTone Ringer
Transcription
USING YOUR CrystalTone Ringer
305-010100 6/30/06 4:40 PM Page 1 SAFETY INSTRUCTIONS PARTS LIST Please verify that the following are enclosed with your new CrystalTone Ringer. Then, open this booklet for operating and installation instructions. • 7-foot telephone line cord • 2, plastic wall anchors • 2, screws SPECIFICATIONS Physical Dimensions Ring Volume Size: 6.4" x 1.6" x 4.1" Weight: 11 oz. Up to 95 dB Controls FCC approved FCC registration number: D8KUSA-40098-KX-N REN: 1.0B Safety: CSA NRTL\C both US and Canada Industry Canada: 721 10620A On/Off Ring Volume Ring Pattern Ring Tone Indicator Lights Ring Flasher Connections Plugs into a standard, analog telephone line (RJ11/CA11A). Approvals 1. Read and understand all instructions. 2. Follow all warnings and instructions on the CrystalTone Ringer. 3. For indoor use only. 4. Unplug the CrystalTone Ringer from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 5. Do not use the CrystalTone Ringer near water, for example, near a bath tub, in a wet basement or near a swimming pool. 6. Do not place the CrystalTone Ringer on an unstable surface. 7. Do not allow anything to rest on the telephone cord. Do not locate the CrystalTone Ringer where people can walk on the cord. 8. To reduce the risk of electric shock, do not disassemble the CrystalTone Ringer. Take it to a qualified service person when service or repair work is required. Opening the unit or incorrect re-assembly can expose you to dangerous voltages or other risks. The CrystalTone Ringer does not have any user-serviceable parts. 9. Unplug the CrystalTone Ringer from the wall outlet and refer servicing to qualified service personnel under the following conditions: (a) If liquid has been spilled into the ringer. (b) If the ringer has been exposed to rain or water. (c) If the ringer does not operate normally. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage. (d) If the ringer has been dropped and/or damaged. (e)If the ringer exhibits a distinct change in performance. FCC INFORMATION This equipment complies with Part 68 of the FCC rules for the United States. The telephone jack used on the CrystalTone Ringer complies with FCC Part 68, Subpart F rules and regulations and is an RJ11C. A label is located on the underside of the ringer containing the FCC registration number and the Ringer Equivalence Number (REN). You must, upon request, provide the following information to your local telephone company: USOC Jack Type: RJ11; REN: 1.0B. The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most areas, the sum of RENs should not exceed five (5.0). For more information, contact the local telephone company. Should you experience trouble with this telephone equipment, please contact Ultratec National Service Center, 5901 Research Park Blvd., Madison, WI 53719. Email: [email protected]. For repair or warranty information, please contact Ultratec Inc. Customer Service at (608) 238-5400 (V/TTY). This equipment cannot be used on public coin phone service provided by the telephone company. Connection to party line service is subject to state tariffs. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. Your telephone company may discontinue your service if your equipment causes harm to the telephone network. Occasionally, your telephone company may make changes in its facilities, equipment, operation, or procedures that could affect the operation of your equipment. INDUSTRY CANADA WARNINGS NOTICE: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Number of all the devices does not exceed 5. USING YOUR CrystalTone Ringer™ AVIS D'INDUSTRIE CANADA AVIS: L'étiquette d'Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection, d'exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n'assure toutefois pas que le matériel fonctionnera à la satisfaction de l'utilisateur. Avant d'installer ce matériel, l'utilisateur doit s'assurer qu'il est permis de le raccorder aux installations de l'entreprise locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée de raccordement. L'abonné ne doit pas oublier qu'il est possible que la comformité aux conditions énoncées ci-dessus n'empêche pas la dégradation du service dans certaines situations. Les réparations de matériel homologué doivent être coordonnées par un représentant désigné par le fournisseur. L'entreprise de télécommunications peut demander á l'utitisateur de débrancher un appareil à la suite de réparations ou de modifications effectuées par l'utilisateur ou à cause de mauvais fonctionnement. Pour sa propre protection, l'utilisateur doit s'assurer que tous les fils de mise à la terre de la source d'énergie électrique, des lignes téléphoniques et des canalisations d'eau métalliques, s'il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales. AVERTISSEMENT: L'utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir recours à un service d'inspection des installations électriques, ou à un électricien, selon le cas. AVIS: L'indice d'équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d'une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition que la somme d'indices d'équivalence de la sonnerie de tous les dispositifs n'excède pas 5. VOLUME TONE RING PATTERN Line-Powered Model 450 Science Drive Madison, WI 53711 (608) 238-5400 www.ultratec.com May 2000 © 2000 Ultratec, Inc. 305-010100 305-010100 6/30/06 4:40 PM Page 2 OVERVIEW INSTALLATION The Ultratec CrystalTone Ringer lets you know when you receive a call. Use it in addition to your telephone or in another part of your home or office to help you hear when the telephone rings. The CrystalTone Ringer has several features to make hearing the telephone ring as carefree as possible. Slide the VOLUME control to the right to increase the ring volume. This can be set as loud as 95 dB. Depress the ON/OFF button to turn the ring volume on. Even with the ringer turned off, the Ring Indicator lights when a call comes in. The adjustable TONE ensures a clear ring at various frequencies. Slide the TONE control to the right for a higher-pitched ring. You can even select from four RING PATTERNS. Select the combination of RING PATTERN and TONE that is right for you. Step 1 - Selecting the Location CAUTION! Do not plug the CrystalTone Ringer into any telephone line other than a typical, analog telephone line. Connection to a digital system may damage the ringer or the telephone system and will void your warranty. Set up the CrystalTone Ringer in a place where: (a) There is a phone jack nearby. Cords should not lie across any walkway. (b) The surface that the ringer is set on, or mounted to, is stable and secure. (c) The area is protected from excessive heat or humidity. Step 3 - Setting up the CrystalTone Ringer Telephone line jacks Volume slide control Ring Tone slide control Ring Pattern selector VOLUME Ring Indicator TONE RING PATTERN Ring On/Off button Placing on a desktop 1. Plug the telephone line cord into the telephone line jack on the bottom of the CrystalTone Ringer and the other end into the wall phone jack. 2. Set the CrystalTone Ringer on a sturdy surface such as a desk. It may be placed on its side or flat. Mounting on a Wall Use the previous instructions with the following exceptions: 1. Select a spot within a few inches of the wall phone jack. 2. Using the template below, drill 2 holes that are 2.3 inches apart. Use a 3/16" drill bit. 3. With a hammer, tap the plastic wall anchors into holes until flush with wall. 4. Using a Phillips head screw driver, insert screws into the anchors until head of screw is 1/4" from wall. 5. Align holes on back of CrystalTone Ringer with screws and hang the ringer on the wall. Use 3/16" drill bit. 2.3 inches One-Year Limited Warranty Ultratec, Inc. offers a one-year warranty for the CrystalTone Ringer. Warranty service is available through Ultratec. If your product needs service, return it to: Ultratec National Service Center, 5901 Research Park Blvd., Madison, WI 53719. Warranty Terms Ultratec shall repair or replace a defective product, at Ultratec’s option, free of charge if returned to Ultratec, freight prepaid, within one year after the product has been shipped to Purchaser; provided, however, that Purchaser shall give Ultratec written notice within said time period of the fact of such defective product and shall also indicate in writing the nature of the defect upon returning the defective product to Ultratec. This warranty covers defects in materials and workmanship only. It does not cover damage caused by accidents, defects or damage resulting from misuse, abuse, or disregard for reasonable care, or damage caused by subjecting the product to unspecified electrical voltage or attaching inappropriate devices (including, but not limited to, damage caused by lightning and connecting the product to digital telephone systems). OTHER THAN AS STATED HEREIN, THERE ARE NO OTHER WARRANTIES, WHETHER BY SAMPLE OR MODEL, BY DESCRIPTION OR QUANTITY, WHETHER EXPRESSED OR IMPLIED, AND THERE ARE NO IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR OF MERCANTABILITY. THIS WARRANTY SHALL BE LIMITED TO THE FOREGOING OBLIGATIONS OF ULTRATEC AND SPECIFICALLY EXCLUDES ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM DEFECTS IN THE PRODUCT. In the case that the product specified above is shipped to an Ultratec service center for warranty service, the owner is responsible for payment of shipping charges. Because damage during shipment is not covered by this warranty, the product should be insured for shipment by the owner.