RondoRex w21 Time switch
Transcription
RondoRex w21 Time switch
™ ● LEXIC GB Time switch Operating instructions RondoRex w21 ® NT 29 17 54 02 Technical data 036 84 036 85 036 86 94 41 78 230V~ 120V~ 24V~ 12V DC 50/60 Hz ca. 0,6W 1 changeover contact 10A 250V~µ cos ϕ = 1 not allowed ±2,5s/d single strand multi strand 1 to 4 mm2 0,5 to 2,5 mm2 28 20h -10°C to +60°C 0°C to +55°C Supply voltage: Frequency: Consumption: Contact rating: Parallel compensation: accuracy: Terminal capacity: 12 Program pictures: Battery reserve: Storage ambient: Working ambient: Safety notes • Installation of these products should only be undertaken by a qualified electrician. • The operational and electrical safety is only guaranteed, if the product is installed using its proper accessories, in a position as specified in the installation instructions (distribution panel, surface or wallbox (front of panel). • Any interference with the product makes the guarantee void. • If the time switch is mounted near equipment where heat produced raises the local ambient above 55°C. Then a space should be put between the time switch and the equipment (e.g. 1⁄2 space module code 044 40 or 1 space module code 044 41). Function The RondoRex w21 is a digitall 7 day time switch with a round segmented display for general rail mounting use. Up to 4 program pictures per day can be set. A program picture incorporates both on and off time. The copying function enables program to be copied to other days. Different programs can be set on each day. The minimum switching time is 1 minute. Program pictures are protected but can be overlaid by other programs. Programs are displayed with a minimum segment size of 15 minutes. Time of day and weekday number are digitally displayed. Presentation State of contact: = On / = Off Blinking clock symbol = set time of day Constant clock symbol = Time switch running 24 Blinking hand symbol = continuous manual operating Constant hand symbol = manual override 18 Real time, set on time or set off time 6 3 Actual day of the week or program day Symbol for program input or interrogation 12 Segment display of the existing program 1 segment = 15 minutes, 4 programs per day max. Pr Change from day to hour, minute, programming, switching time, copying programs Connection Accepting the on and off times, manual switching C Setting days, hours, minutes, on and off times 1. Starting 1 Reset 1 2 Switching programs remain 24 18 Press 6 1 together 12 Reset 2 Switching programs deleted Press 3 4 together 5 24 Hold , and let free 18 6 1 Hold for 5 seconds, then let free 12 1. Weekday and Time setting 2. Setting switching times 24 Press until blinks 18 24 6 1 Press 4x, switch time, Pr and symbol blinks 18 6 1 12 Press to set weekday 1 = Monday 2 = Tuesday 3 = Wednesday 4 = Thursday 5 = Friday 6 = Saturday 7 = Sunday 12 Pr 1. on time setting Setting advances in minutes 24 24 18 6 3 Press once = 1 minute Hold = 15 minutes steps 18 6 1 12 12 Pr Correction To set number to zero Press together 24 Press 1x, hours blink 18 6 3 Press to set actual time (hour) 24 12 Confirm ON time Press 1x 18 6 3 Press to set actual time (minute) Press once = 1 minute Hold = 5 minute steps 6 1 12 Pr 24 Press 1x, minutes blink 18 1. off time setting Setting advances in minutes 24 12 18 Press once = 1 minute Hold = 15 minutes steps Correction To set number to zero. Press together. 6 1 12 Pr Confirm OFF time Press 1x 24 18 6 1 12 Pr 24 End time setting Press as required appears 18 6 3 12 Make further settings as above . A maximum of 4 ON and 4 OFF times can be set. With button the setting can be copied to the next day.This can only be done during initial setting or after a reset. 3. Continuous switching Switching must be changed to hand control Press for 2 seconds until Delete switching times Press and together blinks 24 24 Display = ON, Segmented display appears 18 6 3 12 Display = OFF Segmented display invisible Confirm program setting Press as required until 18 6 3 12 appears 24 18 6 4. Hand ON/OFF 3 12 Press Press until to choose appears 1x to choose 6 3 Display = ON Display = OFF 12 24 Display = ON, Segmented display appears 18 6 3 The next programm automatically returns the switch to ON or OFF as programmed. 12 Display = OFF Segmented display invisible 24 18 6 3 5. Summer/ winter setting 12 End continuous switching Press for 2 seconds until 24 18 appears Supply failure On supply failure the segmented display blinks. Buttons are inoperative. Reset is possible Press 2x until blinks. Press until actual hour is reached Press 1x Press until actual minute is reached 24 18 6 3 12 Ending the time changeover Press 8x until blinks.