Sun Fire V100 Server Product Notes

Sun Fire™ V100 Server
Product Notes
Sun Microsystems, Inc.
901 San Antonio Road
Palo Alto, CA 94303-4900 U.S.A.
650-960-1300
Part No. 816-2754-13
May 2002 Revision A
Send comments about this document to: [email protected]
Copyright 2002 Sun Microsystems, Inc., 901 San Antonio Road, Palo Alto, CA 94303-4900 U.S.A. All rights reserved.
This product or document is distributed under licenses restricting its use, copying, distribution, and decompilation. No part of this product or
document may be reproduced in any form by any means without prior written authorization of Sun and its licensors, if any. Third-party
software, including font technology, is copyrighted and licensed from Sun suppliers.
Parts of the product may be derived from Berkeley BSD systems, licensed from the University of California. UNIX is a registered trademark in
the U.S. and other countries, exclusively licensed through X/Open Company, Ltd.
Sun, Sun Microsystems, the Sun logo, AnswerBook2, docs.sun.com, Netra, and Solaris are trademarks, registered trademarks, or service marks
of Sun Microsystems, Inc. in the U.S. and other countries. All SPARC trademarks are used under license and are trademarks or registered
trademarks of SPARC International, Inc. in the U.S. and other countries. Products bearing SPARC trademarks are based upon an architecture
developed by Sun Microsystems, Inc.
The OPEN LOOK and Sun™ Graphical User Interface was developed by Sun Microsystems, Inc. for its users and licensees. Sun acknowledges
the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry. Sun
holds a non-exclusive license from Xerox to the Xerox Graphical User Interface, which license also covers Sun’s licensees who implement OPEN
LOOK GUIs and otherwise comply with Sun’s written license agreements.
Federal Acquisitions: Commercial Software—Government Users Subject to Standard License Terms and Conditions.
DOCUMENTATION IS PROVIDED “AS IS” AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT,
ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID.
Copyright 2002 Sun Microsystems, Inc., 901 San Antonio Road, Palo Alto, CA 94303-4900 Etats-Unis. Tous droits réservés.
Ce produit ou document est distribué avec des licences qui en restreignent l’utilisation, la copie, la distribution, et la décompilation. Aucune
partie de ce produit ou document ne peut être reproduite sous aucune forme, par quelque moyen que ce soit, sans l’autorisation préalable et
écrite de Sun et de ses bailleurs de licence, s’il y en a. Le logiciel détenu par des tiers, et qui comprend la technologie relative aux polices de
caractères, est protégé par un copyright et licencié par des fournisseurs de Sun.
Des parties de ce produit pourront être dérivées des systèmes Berkeley BSD licenciés par l’Université de Californie. UNIX est une marque
déposée aux Etats-Unis et dans d’autres pays et licenciée exclusivement par X/Open Company, Ltd.
Sun, Sun Microsystems, le logo Sun, AnswerBook2, docs.sun.com, Netra, et Solaris sont des marques de fabrique ou des marques déposées, ou
marques de service, de Sun Microsystems, Inc. aux Etats-Unis et dans d’autres pays. Toutes les marques SPARC sont utilisées sous licence et
sont des marques de fabrique ou des marques déposées de SPARC International, Inc. aux Etats-Unis et dans d’autres pays. Les produits portant
les marques SPARC sont basés sur une architecture développée par Sun Microsystems, Inc.
L’interface d’utilisation graphique OPEN LOOK et Sun™ a été développée par Sun Microsystems, Inc. pour ses utilisateurs et licenciés. Sun
reconnaît les efforts de pionniers de Xerox pour la recherche et le développement du concept des interfaces d’utilisation visuelle ou graphique
pour l’industrie de l’informatique. Sun détient une licence non exclusive de Xerox sur l’interface d’utilisation graphique Xerox, cette licence
couvrant également les licenciés de Sun qui mettent en place l’interface d’utilisation graphique OPEN LOOK et qui en outre se conforment aux
licences écrites de Sun.
LA DOCUMENTATION EST FOURNIE “EN L’ETAT” ET TOUTES AUTRES CONDITIONS, DECLARATIONS ET GARANTIES EXPRESSES
OU TACITES SONT FORMELLEMENT EXCLUES, DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE, Y COMPRIS NOTAMMENT
TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE, A L’APTITUDE A UNE UTILISATION PARTICULIERE OU A
L’ABSENCE DE CONTREFAÇON.
Please
Recycle
Introduction
This document provides information that became available after the Sun Fire™ V100
Server User’s Guide went to print.
The document contains the following sections:
■
“Available Online Documentation” on page 4
■
“System Software Requirements” on page 4
■
“Reinstalling the Solaris Operating Environment” on page 4
■
“Using the Solaris Network Cache and Accelerator (SNCA)” on page 4
■
“Front Bezel” on page 5
■
“Precautions for Using the System Configuration Card” on page 6
■
“Open Issues” on page 6
■
“Optional Components” on page 9
■
“Hardware Configurations” on page 9
■
“Operating Power Statistics” on page 10
3
Available Online Documentation
Online documentation is available at the following URL:
http://www.sun.com/products-n-solutions/hardware/docs
Check this site periodically for the latest versions of the product documentation.
System Software Requirements
The Sun Fire V100 server requires the Solaris 8 (2/02) Operating Environment or
later. The server is supplied with this software preinstalled.
Reinstalling the Solaris Operating
Environment
The earliest version of the Solaris operating environment supported on the Sun Fire
V100 server is Solaris 8 (2/02).
To reinstall the Solaris operating environment onto a Sun Fire V100 server, refer to
the Solaris Installation Guide (806-0955-10) and the Solaris Advanced Installation Guide
(806-0957-10).
Using the Solaris Network Cache and
Accelerator (SNCA)
The Solaris Network Cache and Accelerator (SNCA) is a caching server which
provides improved web performance to the Solaris Operating Environment. It is
available on Solaris 8 (07/01) or later.
The steps below tell you how to enable SNCA to work with iPlanet Web Server.
4
Sun Fire V100 Server Product Notes • May 2002
Note – Ensure you have the required NCA-specific software patches installed on the
server before you continue with this procedure.
1. In the Solaris operating environment, edit the configuration interface file
/etc/nca/nca.if and add * to the first non-comment line.
This enables SNCA for all network interfaces.
2. Make the following changes to the /etc/nca/ncakmod.conf file:
■
■
set the status field to enabled
set the ncad_status field to enabled
3. Make the following change to the /etc/nca/ncalogd.conf file:
■
set the status field to enabled
4. Reboot the server.
The changes you have just made will not take effect until the server is rebooted.
5. In the iPlanet Web Server server.xml file, ensure the listen socket on port 80
includes family="nca", as shown below:
<LS id="ls1" ip="0.0.0.0" port="80" family="nca" security="off"
acceptorthreads="1">
The server must be listening on port 80 for this to work.
6. Restart the server.
The changes you have just made will not take effect until the server is rebooted.
For more information, go to the URL below.
■
http://docs.iplanet.com/docs/manuals/enterprise/50/tuning/conte
nts.htm
Front Bezel
There is a blank nameplate built into the bezel, just below the Sun Fire V100 badge.
This allows you to easily attach a unique identifier to the server.
5
Precautions for Using the System
Configuration Card
The Sun Fire V100 server contains a memory card (located on the back panel) called
the system configuration card. This card contains the system’s MAC address, serial
number, and other configuration settings. It is designed to be removable so that, if
you ever need to replace an entire server, you can transfer the host ID and
configuration data onto the new server. This makes the replacement of the server
transparent to your network.
Caution – Never remove the system configuration card when the server is booting
or running Solaris. Power the server off or down to standby mode before removing
or inserting the system configuration card.
Caution – Do not handle the system configuration card unless you need to transfer
it to another system. If you need to handle it for this reason, avoid contact with the
gold terminals on the underside of the card.
For information about transferring the system configuration card from one server to
another, refer to the Sun Fire V100 Server User’s Guide (816-2756-10).
Open Issues
The following sections cover some open issues with the Sun Fire V100 server.
64 Bit Support
When installing a system, ensure that the selected install option supports the 64 bit
kernel.
Note – The install option that takes up the least disk space, labelled “Core System
Support”, supports 32 bit operation only and is not compatible with the Sun Fire
V100 server.
6
Sun Fire V100 Server Product Notes • May 2002
Sending Break During Boot Process Can Result In
Failure To See Disk On Reset
If a break is sent to the system console while the system is booting, there is a small
chance of a subsequent failure to detect the boot disk. The prom may report:
Boot device: disk File and args:
Bad checksum in disk label
Can’t open disk label package
Evaluating: boot
Can’t open boot device
To recover, power the system off for 1 minute and then power it back on.
7
No Auto Power-On When Power is Removed and
Restored Within 10 Seconds
If you disconnect the server from its power source while it is powered on, and then
reconnect it within 10 seconds of the disconnection, the server automatically
attempts to power on. However, it does not reinitialize successfully and hangs after
giving the following console output:
LOMlite starting up.
CPU type: H8/3437S, mode 3
Ram-test: 2048 bytes OK
Initialising i2c bus: OK
Searching for EEPROMs: 50(cfg)
I2c eeprom @50: OK
i2c bus speed code 01... OK
Probing for lm80s: none
Probing for lm75s: 48
Initialising lm75 @48: OK
System functions: PSUs fans breakers rails gpio temps host CLI ebus
clock
Unexpected reset
LOMlite console
lom>
LOM event: +0h0m0s LOM FAULT: unexpected reset
lom>
LOM event: +0h0m0s host power on
If your system hangs when you have disconnected power and then restored it within
10 seconds of the disconnection, do either of the following:
■
Type a carriage return and then type the LOM escape sequence (a hash character,
followed by a dot: #.). At the LOM prompt, type poweroff. At the next LOM
prompt, type poweron. The system will power on.
■
Hold the rocker switch in the OFF position until the console reports the timestamped host power off LOM event, then put the rocker switch into the ON
position. The system will then power on.
If you have the NVRAM diag-switch? parameter set to true (by default, it is set
to false and the console output is as shown above), the system will provide
additional, Open Boot PROM output during the boot process. In this case, if you
restore power within 10 seconds of removing it, the system hangs after reporting the
following message:
8
Sun Fire V100 Server Product Notes • May 2002
Probing/pci@1f,0 Device a usb
To restore power, use either of the two methods described above.
Note – Any interruption and subsequent restoration of mains power within 10
seconds could cause this fault to occur.
Optional Components
There is an error on page 4 of the Sun Fire V100 Server User’s Guide. The part
number for the 512-Mbyte DIMM is incorrectly given as X7084A. The correct part
number is X7092A.
Hardware Configurations
This section contains additional information to that contained in the table on page
108 of the Sun Fire V100 Server User’s Guide (816-2756-10). The table below gives the
configuration information for servers containing the 550 MHz and 650 MHz
processor.
Processor
RAM
Hard Disk Drive
Sun Part Number
550 MHz
256 MB (1*256 MB)
1*40 GB (7200 rpm)
600-7995-xx
550 MHz
512 MB (2*256 MB)
1*40 GB (7200 rpm)
600-7996-xx
650 MHz
1 GB (4*256 MB)
2*40 GB (7200 rpm)
600-7997-xx
650 MHz
2 GB (4*512 MB)
2*40 GB (7200 rpm)
600-7998-xx
9
Operating Power Statistics
This section contains additional information to that given in the table on page 117 of
the Sun Fire V100 Server User’s Guide (816-2756-10). The BTU/hr figure for servers
containing the 550 MHz and 650 MHz processor is given below.
■
10
500/550/650 MHz processor: 148 (min), 280 (max).
Sun Fire V100 Server Product Notes • May 2002