Release Notes for the Catalyst 4500 Series Switch, Cisco IOS

Transcription

Release Notes for the Catalyst 4500 Series
Switch, Cisco IOS Releases 15.2(2)Ex
Current release
IOS 15.2(2)E5a—October 14, 2016
Prior releases
IOS 15.2(2)E5—June 07, 2016, IOS 15.2(2)E4, IOS 15.2(2)E3, IOS 15.2(2)E2, IOS 15.2(2)E1, IOS 15.2(2)E0—June 27, 2016
These release notes describe the features, modifications, and caveats for Cisco IOS Release 15.2(2)Ex
on the Catalyst 4500 series switch.
Support for Cisco IOS Software Release 15.2(2)Ex follows the standard Cisco Systems® support policy,
available at
http://www.cisco.com/en/US/products/products_end-of-life_policy.html
For more information on the Catalyst 4500 Series Switches, visit:
http://www.cisco.com//en/US/products/hw/switches/ps4324/index.html
Note
Although their Release Notes are unique, the platforms Catalyst 4900M/Catalyst 4948E/Catalyst
4948E-F and Catalyst 4500 leverage the same Software Configuration Guide, Command Reference
Guide, and System Message Guide.
Contents
This publication consists of these sections:
•
Cisco IOS Software Packaging, page 2
•
Cisco Classic IOS Release Strategy, page 2
•
System Requirements, page 3
•
New and Changed Information, page 26
•
Upgrading the System Software, page 28
•
Limitations and Restrictions, page 32
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Cisco IOS Software Packaging
•
Caveats, page 43
•
Related Documentation, page 49
•
Notices, page 50
•
Obtaining Documentation and Submitting a Service Request, page 52
Cisco IOS Software Packaging
The Enterprise Services image supports all Cisco Catalyst 4500 Series software features based on Cisco
IOS Software, including enhanced routing. Customers planning to enable BGP for Supervisor Engine
IV, V, or V-10GE will no longer need to purchase a separate BGP license (FR-IRC4) because BGP is
included in the Enterprise Services package. Beginning with 12.2(53)SG2, we support the Enterprise
Services image on Supervisor Engine 6L-E.
The IP Base image supports Open Shortest Path First (OSPF) for Routed Access, Enhanced Interior
Gateway Routing Protocol (EIGRP) "limited" Stub Routing, Nonstop Forwarding/Stateful Switchover
(NSF/SSO), and RIPv1/v2. The IP Base image does not support enhanced routing features such as BGP,
Intermediate System-to-Intermediate System (IS-IS), Full OSPF, Full Enhanced Interior Gateway
Routing Protocol (EIGRP) & Virtual Routing Forwarding (VRF-lite).
Cisco IOS Release 12.2(46)SG1 introduced a new LAN Base software and an IP upgrade image. These
complement the existing IP Base and Enterprise Services images. The LAN base image is supported on
Supervisor Engine 6L-E starting with Cisco IOS Release 12.2(52)XO. LAN Base image is primarily
focused on customer access and Layer 2 requirements and therefore many of the IP Base features are not
required. The IP upgrade image is available if at a later date you require some of those features.
Starting with Cisco IOS Release 15.0(2)SG, on the Catalyst 4500 Series Switch, support for NEAT
feature has been extended from IP Base to LAN Base and support for HSRP v2 IPV6 has been extended
from Enterprise Services to IP Base.
Starting with Cisco IOS Release 15.2(1)E, OSPF Routed Access in IP Base support rose to 1000 routes.
Cisco Classic IOS Release Strategy
Customers using Supervisor Engine 6-E or 6L-E with Catalyst 4500 Series Switches who need the latest
hardware and software features should migrate to Cisco IOS Release 15.2(2)E.
The Catalyst 4500 Series Switch has three extended maintenance (EM) trains: 15.2(2)Ex, 15.1(2)SGx,
and 15.0(2)SGx. Cisco IOS Release 12.2(54)SG, 15.1(1)SG, and 15.2(1)E are standard maintenance
releases.
Figure 1 displays the maintenance trains for the Catalyst 4500 series switch.
Release Notes for the Catalyst 4500 Series Switch, Cisco IOS Releases 15.2(2)Ex
2
System Requirements
Figure 1
Software Release Strategy for the Catalyst 4500 Series Switch
SM
EM
SM
EM
SM
EM
346101
12.2(54)SG 15.0(2)SG 15.1(1)SG 15.1(2)SG 15.2(1)E 15.2(2)E
Support
Support for Cisco IOS Software Release 15.2(2)E follows the standard Cisco Systems® support policy,
available at
http://www.cisco.com/en/US/products/products_end-of-life_policy.html
System Requirements
This section describes the system requirements:
•
Supported Hardware on Catalyst 4500 Series Switch, page 3
•
Supported Hardware on Catalyst 4500 E-Series Switch, page 7
•
Feature Support by Image Type, page 8
•
MIB Support, page 24
•
Features Not Supported on the Cisco Catalyst 4500 Series Switch, page 24
•
Orderable Product Numbers, page 25
Supported Hardware on Catalyst 4500 Series Switch
Table 1 lists the hardware supported on the Catalyst 4500 Series Switch.
Table 1
Supported Hardware
Product Number (append Product Description
with “=” for spares)
Software Release
Minimum
Supervisor Engines
WS-X45-Sup6-E
Catalyst 4500 E-series switch Supervisor Engine 6-E
Note
WS-X45-Sup6L-E
This engine is supported on legacy and E-series chassis.
Catalyst 4500 E-series switch Supervisor Engine 6L-E
Note
12.2(40)SG
12.2(52)XO
This engine is supported on legacy and E-series 3,6, and 7 slot
chassis.
3
System Requirements
Table 1
Supported Hardware (continued)
Software Release
Minimum
Gigabit Ethernet Switching Modules
WS-X4302-GB
2-port 1000BASE-X (GBIC) Gigabit Ethernet module
12.1(19)EW
WS-X4306-GB
6-port 1000BASE-X (GBIC) Gigabit Ethernet switching module
12.1(8a)EW
WS-X4418-GB
18-port 1000BASE-X (GBIC) Gigabit Ethernet server switching module
12.1(8a)EW
WS-X4412-2GB-T
12-port 1000BASE-T Gigabit Ethernet and 2-GBIC ports switching module 12.1(8a)EW
WS-X4424-GB-RJ45
24-port 10/100/1000BASE-T Gigabit Ethernet RJ-45 switching module
12.1(8a)EW
WS-X4448-GB-LX
48-port 1000BASE-LX (small form-factor pluggable) Gigabit Ethernet
fiber optic interface switching module
12.1(8a)EW
WS-X4448-GB-RJ45
48-port 10/100/1000BASE-T Gigabit Ethernet switching module
12.1(8a)EW
WS-X4448-GB-SFP
48-port 1000BASE-X (small form-factor pluggable) module
12.2(20)EW
WS-X4506-GB-T
6-port Alternately-Wired 10/100/1000BASE-T Catalyst 4500 series Power 12.2(20)EWA
over Ethernet (PoE) 802.3af or 1000BASE-X SFP
WS-X4524-GB-RJ45V
24-port 10/100/1000BASE-T RJ-45 Catalyst 4500 series PoE 802.3af
12.2(18)EW
WS-X4548-GB-RJ45
48-port 10/100/1000BASE-T Gigabit Ethernet module
12.1(19)EW
WS-X4548-GB-RJ45V
48-port 10/100/1000BASE-T RJ-45 Catalyst 4500 series PoE 802.3af
12.2(18)EW
WS-X4548-RJ45V+
48-port 10/100/1000 Premium PoE line card
12.2(50)SG
WS-X4624-SFP-E
Non-blocking 24-port 1000BASEX (small form factor pluggable) module
12.2(44)SG
WS-X4640-CSFP-E
15.1(1)SG
80 ports with Gigabit compact SFP (4:1 oversubscribed); 40 modules of
Gigabit SFP line card (1000BaseX), providing 24 gigabits per-slot capacity
(SFP optional) (2:1 oversubscribed)
WS-X4648-RJ45V-E
48 port 10/100/1000 Mb with 2 to 1 oversubscription
12.2(40)SG
WS-X4648-RJ45V+E
48 port 10/100/1000 Mb with 2 to 1 oversubscription
12.2(40)SG
Fast Ethernet Switching Modules
WS-X4124-FX-MT
24-port 100BASE-FX Fast Ethernet MT-RJ multimode fiber switching
module
12.1(8a)EW
WS-X4148-FX-MT
48-port 100BASE-FX Fast Ethernet MT-RJ multimode fiber switching
module
12.1(8a)EW
WS-X4148-FE-LX-MT
48-port 100BASE-LX10 Fast Ethernet MT-RJ single-mode fiber switching 12.1(13)EW
module
WS-X4148-FE-BD-LC
48-port 100BASE-BX10-D module
12.2(18)EW
WS-X4248-FE-SFP
48-port 100BASE-X SFP switching module
12.2(25)SG
WS-U4504-FX-MT
4-port 100BASE-FX (MT-RF) uplink daughter card
12.1(8a)EW
Ethernet/Fast Ethernet (10/100) Switching Modules
WS-X4124-RJ45
24-port 10/100 RJ-45 module
12.2(20)EW
WS-X4148-RJ
48-port 10/100 RJ-45 switching module
12.1(8a)EW
WS-X4148-RJ21
48-port 10/100 4xRJ-21 (telco connector) switching module
12.1(8a)EW
4
System Requirements
Table 1
Supported Hardware (continued)
WS-X4148-RJ45V
Software Release
Minimum
48-port Pre-standard PoE 10/100BASE-T switching module
12.1(8a)EW for
data support
12.1(11b)EW for
data and inline
power support
WS-X4224-RJ45V
24-port 10/100BASE-TX RJ-45 Cisco Catalyst 4500 series PoE 802.3af
12.2(20)EW
WS-X4232-GB-RJ
32-port 10/100 Fast Ethernet RJ-45, plus 2-port 1000BASE-X (GBIC)
Gigabit Ethernet switching module
12.1(8a)EW
WS-X4248-RJ45V
48-port 10/100BASE-T RJ-45 Cisco Catalyst 4500 series PoE 802.3af
12.2(18)EW
WS-X4248-RJ21V
48-port 10/100 Fast Ethernet RJ-21 Cisco Catalyst 4500 series PoE 802.3af 12.2(18)EW
telco
WS-X4232-RJ-XX
32-port 10/100 Fast Ethernet RJ-45 modular uplink switching module
12.1(8a)EW
MEM-C4K-FLD64M
Catalyst 4500 series switch CompactFlash, 64 MB Option
12.1(8a)EW
MEM-C4K-FLD128M
Catalyst 4500 series switch CompactFlash, 128 MB Option
12.1(8a)EW
WS-F4531
Catalyst 4500 series switch NetFlow Services Card on Catalyst 4500 series 12.1(13)EW
switch Supervisor Engines IV and V
WS-X4590=
Catalyst 4500 series switch Fabric Redundancy Modules
12.2(18)EW
PWR-C45-1000AC
Catalyst 4500 series switch 1000 Watt AC power supply for chassis 4503,
4506, and 4507R (data only)
12.1(12c)EW
PWR-C45-1400DC
Catalyst 4500 series switch 1400 Watt DC triple input power supply
(data-only)
12.2(25)EW
PWR-C45-1400DC-P
Catalyst 4500 series switch 1400 Watt DC power supply with integrated
PEM
12.1(19)EW
PWR-C45-1400AC
Catalyst 4500 series switch 1400 Watt AC power supply (data-only)
12.1(12c)EW
PWR-C45-1300ACV
Catalyst 4500 series switch 1300 Watt AC power supply with integrated
voice for chassis 4503, 4506, and 4507R
12.1(12c)EW
PWR-C45-2800ACV
Catalyst 4500 series switch 2800 Watt AC power supply with integrated
voice (data and PoE) for chassis 4503, 4506, and 4507R
12.1(12c)EW
PWR-C45-4200ACV
Catalyst 4500 series switch 4200 Watt AC dual input power supply with
integrated voice (data and PoE)
12.2(25)EWA5
WS-P4502-1PSU
Catalyst 4500 series switch auxiliary power shelf (25-slot), including
one PWR-4502
12.1(19)EW
PWR-4502
Catalyst 4500 series switch auxiliary power shelf redundant power supply
12.1(19)EW
PWR-C45-6000ACV
Catalyst 4500 Series Switch 6000 W AC power supply
12.2(53)SG
PWR-C45-9000ACV
Catalyst 4500 Series Switch 9000 W AC power supply
XE 3.4(0)SG,
15.1(2)SG
Other Modules
5
System Requirements
Table 1 briefly describes the four chassis in the Catalyst 4500 Series Switch. For the chassis listed in the
table, refer to Table 4 on page 8 for software release information.
Chassis Description for the Catalyst 4500 Series Switch
Product Number (append
Description of Modular Chassis
WS-C4503
Catalyst 4503 chassis includes these components:
WS-C4506
3 slots
•
Fan tray
Catalyst 4506 chassis includes these components:
WS-C4507R
•
6 slots
•
Fan tray
Catalyst 4507R chassis includes these components:
WS-C4510R
Table 2
•
•
7 slots
•
Fan tray
Catalyst 4510R chassis includes these components:
•
10 slots; slot 10 accepts only the Catalyst 4500 series 2-port
Gigabit Ethernet line card
•
Fan tray
DOM Support on the Catalyst 4500 Series Switch applies to these module
Transceiver Module
CWDM- SFP-xx
DWDM-GBIC-xx
DWDM-SFP
DWDM-X2-xx
GLC-BX-D
GLC-BX-U
GLC-EX-SMD
SFP-10G-SR
SFP-10G-LR
SFP-10G-LRM
SFP-10G-ER
SFP-10G-ZR
6
System Requirements
For details on transceiver module compatibility information, please refer to the URL:
http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html
Supported Hardware on Catalyst 4500 E-Series Switch
In addition to the classic line cards and supervisor engines, Cisco IOS Software Release 15.2(2)E
supports the next-generation high-performance E-Series Supervisor Engine 6-E with CenterFlex
technology and E-Series line cards and chassis. A brief list of primary E-Series hardware supported on
Catalyst 4500 series switch (Table 3).
Table 3
Supported E-Series Hardware
Product Number
Description
WS-C4503-E
Cisco Catalyst 4500 E-Series 3-Slot Chassis
WS-C4506-E
WS-C4507R-E
WS-C4507R+E
WS-C4510R-E
WS-C4510R+E
WS-X45-Sup6-E
•
Fan tray
•
No Power Supply
•
Fan tray
•
No Power Supply
•
Fan tray
•
No Power Supply
•
Redundant supervisor engine capability
Cisco Catalyst 4500 E-Series 7-Slot 48 GB-ready Chassis
•
Fan tray
•
No Power Supply
•
•
Fan tray
•
No Power Supply
•
•
Slots 8, 9, and 10 are limited to 6Gbps when used with a Supervisor
Engine 6-E or a Supervisor Engine 6L-E.
Cisco Catalyst 4500 E-Series 10-Slot 48 GB-ready Chassis
•
Fan tray
•
No Power Supply
•
•
You cannot place a linecard with a backplane traffic capacity
exceeding 6Gbps in slots 8, 9 and 10 of a Catalyst 4510R+E chassis
when used with a Supervisor Engine 6-E or a Supervisor Engine 6L-E.
Cisco Catalyst 4500 E-Series Sup 6-E, 2x10GE(X2) w/ TwinGig
7
System Requirements
Table 3
Supported E-Series Hardware
Product Number
Description
WS-X45-Sup6L-E
Cisco Catalyst 4500 E-Series Sup 6L-E
WS-X4624-SFP-E
Cisco Catalyst 4500 E-series 24-Port 1000BaseX (small form factor
pluggable) module
WS-X4648-RJ45V-E
Cisco Catalyst 4500 E-Series 48-Port PoE 802.3af 10/100/1000(RJ45)
WS-X4648-RJ45V+E
Cisco Catalyst 4500 E-Series 48-Port Premium PoE 10/100/1000
WS-X4606-X2-E
Cisco Catalyst 4500 E-Series 6-Port 10GbE (X2) w/ TwinGig
WS-X4648-RJ45-E
Cisco Catalyst 4500 E-Series 48-Port 10/100/1000(RJ45)
Table 4 outlines the chassis and supervisor engine compatibility.
(M=Minimum release, R=Recommended release)
Table 4
Chassis and Supervisor Compatibility
Chassis
Sup 6-E
Sup 6L-E
WS-C4503-E
M:
12.2(40)SG
M:
12.2(52)XO
WS-C4506-E
M:
12.2(40)SG
M:
12.2(52)XO
WS-C4507R-E
M:
12.2(40)SG
M:
12.2(52)XO
WS-C4507R+E
M: 12.2(54)SG
M: 12.2(54)SG
WS-C4510R-E
M:
12.2(40)SG
WS-C4510R+E
M: 12.2(54)SG
Feature Support by Image Type
Table 5 is a detailed list of features supported on Catalyst 4500 Series Switch running Cisco IOS
Software Release 15.2(2)E. For the full list of supported features, check the Feature Navigator
application:
http://tools.cisco.com/ITDIT/CFN/
Table 5
LAN Base, IP Base, and Enterprise Services Image Support
on the Catalyst 4500 Series Switch
Feature
LAN Base
IP Base
Enterprise
Services
2-way Community Private VLANs
No
Yes
Yes
8-Way CEF Load Balancing
No
Yes
Yes
10G Uplink Use
Yes
Yes
Yes
8
System Requirements
Table 5
Feature
LAN Base
IP Base
Enterprise
Services
AAA Server Group
Yes
Yes
Yes
ACL Logging
Yes
Yes
Yes
ANCP Client
No
Yes
Yes
ANSI TIA-1057 LLDP - MED Location Extension
Yes
Yes
Yes
ANSI TIA-1057 LLDP - MED Support
Yes
Yes
Yes
AppleTalk 1 and 2 (not supported on Sup 6-E and 6L-E)
No
No
Yes
Auto Security
Yes
Yes
Yes
Auto SmartPorts
Yes
Yes
Yes
AutoQoS
Yes
Yes
Yes
Auto-MDIX
Yes
Yes
Yes
Auto-Voice VLAN (part of Auto QoS)
No
Yes
Yes
Bidirectional Forwarding Detection (BFD) Hardware Offload
Support
No
Yes
Yes
BFD - EIGRP Support
No
Yes
Yes
BFD - Static Route Support over IPv4
No
Yes
Yes
BFD IPv6 Encapsulation Support
No
Yes
Yes
BGP Support for BFD
No
No
Yes
BGP
No
No
Yes
BGP 4
No
No
Yes
BGP 4 4Byte ASN (CnH)
No
No
Yes
BGP 4 Multipath Support
No
No
Yes
BGP 4 Prefix Filter and In-bound Route Maps
No
No
Yes
BGP Conditional Route Injection
No
No
Yes
BGP Link Bandwidth
No
No
Yes
BGP Neighbor Policy
No
No
Yes
BGP Prefix-Based Outbound Route Filtering
No
No
Yes
9
System Requirements
Table 5
Feature
LAN Base
IP Base
Enterprise
Services
BGP Route-Map Continue
No
No
Yes
BGP Route-Map Continue Support for Outbound Policy
No
No
Yes
BGP Route-Map Policy List Support
No
No
Yes
BGP Soft Reset
No
No
Yes
BGP Wildcard
No
No
Yes
Bidirectional PIM (IPv4 only)
No
Yes
Yes
BOOTP
Yes
Yes
Yes
Bootup GOLD
No
Yes
Yes
Broadcast/Multicast Suppression
Yes
Yes
Yes
Call Home
No
Yes
Yes
CDP/CDPv2
Yes
Yes
Yes
CFM
Yes
Yes
Yes
CGMP - Cisco Group Management Protocol
Yes
Yes
Yes
Cisco IOS Scripting w/Tcl
Yes
Yes
Yes
CiscoView Autonomous Device Manager (ADP)
Yes
Yes
Yes
CNS
Yes
Yes
Yes
Command Scheduler (Kron)
Yes
Yes
Yes
Community PVLAN support
No
Yes
Yes
Config File
Yes
Yes
Yes
Configuration Replace and Configuration Rollback
Yes
Yes
Yes
Configuration Rollback Confirmed Change
Yes
Yes
Yes
Copy Command
Yes
Yes
Yes
Console Access
Yes
Yes
Yes
Control Plane Policing (CoPP)
Yes
Yes
Yes
CoS to DSCP Map
Yes
Yes
Yes
CPU Optimization for Layer 3 Multicast Control Packets
Yes
Yes
Yes
10
System Requirements
Table 5
Feature
LAN Base
IP Base
Enterprise
Services
Crashdump Enhancement1
Yes
Yes
Yes
DAI (Dynamic ARP Inspection)
Yes
Yes
Yes
DBL (Dynamic Buffer Limiting) - Active Queue Management
Yes
Yes
Yes
Debug Commands
Yes
Yes
Yes
Device Management
Yes
Yes
Yes
DHCPv6 Relay Agent notification for Prefix Delegation
No
Yes
Yes
DHCP Client
Yes
Yes
Yes
DHCP Gleaning
No
Yes
Yes
DHCP Server
Yes
Yes
Yes
DHCP Snooping
Yes
Yes
Yes
DHCPv6 Ethernet Remote ID option
No
Yes
Yes
Diagnostics Tools
Yes
Yes
Yes
Diffserv MIB
Yes
Yes
Yes
Digital Optical Monitoring (DOM)
Yes
Yes
Yes
DSCP to CoS Map
Yes
Yes
Yes
DSCP to egress queue mapping
Yes
Yes
Yes
DSCP/CoS via LLDP
Yes
Yes
Yes
Duplication Location Reporting Issue
No
Yes
Yes
Easy Virtual Network (EVN)
No
No
Yes
EIGRP
No
No
Yes
EIGRP Service Advertisement Framework
Yes
Yes
Yes
EIGRP Stub Routing
No
Yes
Yes
Embedded Event Manager (EEM) 4.0
Yes
Yes
Yes
Embedded Event Manager and EOT integration
No
Yes
Yes
Energywise Agentless SNMP support
Yes
Yes
Yes
Energywise Wake-On-Lan Support
Yes
Yes
Yes
11
System Requirements
Table 5
Feature
LAN Base
IP Base
Enterprise
Services
EPoE
Yes
Yes
Yes
EtherChannel
Yes
Yes
Yes
Ethernet Management Port (Fa1 interface)2
Yes
Yes
Yes
Ethernet Operations, Administration, and Maintenance (OAM)
Yes
Yes
Yes
Event Log
Yes
Yes
Yes
FHRP - Enhanced Object Tracking of IP SLAs
Yes
No
Yes
FHRP - GLBP - IP Redundancy API
No
Yes
Yes
FHRP - HSRP - Hot Standby Router Protocol V2
No
Yes
Yes
FHRP - Object Tracking List
No
Yes
Yes
FIPS 140-2/3 Level 2 Certification
Yes
Yes
Yes
File Management
Yes
Yes
Yes
Flex Links+ (VLAN Load balancing)
Yes
Yes
Yes
Gateway Load Balancing Protocol (GLBP)
No
Yes
Yes
GOLD Online Diagnostics
Yes
Yes
Yes
HSRP: Global IPv6 Address
No
Yes
Yes
HSRP - Hot Standby Router Protocol
No
Yes
Yes
HSRPv2 for IPv6 Global Address Support
No
Yes
Yes
HTTP TACAC+ Accounting support
Yes
Yes
Yes
Identity 4.1 ACL Policy Enhancements
Yes
Yes
Yes
Identity 4.2: MAB with Configurable User Name/Password
Yes
Yes
Yes
Identity 4.1 Network Edge Access Topology
Yes
Yes
Yes
ID 4.0 Voice Vlan assignment
Yes
Yes
Yes
ID 4.1 Filter ID and per use ACL
Yes
Yes
Yes
IEEE 802.1ab LLDP (Link Layer Discovery Protocol)
Yes
Yes
Yes
IEEE 802.1ab LLDP/LLDP-MED
Yes
Yes
Yes
IEEE 802.1ab LLDP enhancements (PoE+Layer 2 COS)
Yes
Yes
Yes
12
System Requirements
Table 5
Feature
LAN Base
IP Base
Enterprise
Services
IEEE 802.1ag D8.1 standard Compliant CFM, Y.1731 multicast
LBM / AIS / RDI / LCK, IP SLA for Ethernet
Yes
Yes
Yes
IEEE 802.1p Support
Yes
Yes
Yes
IEEE 802.1p Prioritization
Yes
Yes
Yes
IEEE 802.1p/802.1q
Yes
Yes
Yes
IEEE 802.1Q Tunneling
Yes
Yes
Yes
IEEE 802.1Q VLAN Trunking
Yes
Yes
Yes
IEEE 802.1s Multiple Spanning Tree (MST) Standard
Compliance
Yes
Yes
Yes
IEEE 802.1w Spanning Tree Rapid Reconfiguration
Yes
Yes
Yes
IEEE 802.1x (Auth-Fail VLAN, Accounting)
Yes
Yes
Yes
IEEE 802.1x Critical Authorization for Voice and Data
Yes
Yes
Yes
IEEE 802.1x Flexible Authentication
Yes
Yes
Yes
IEEE 802.1x with Multiple authenticated, multi-host
Yes
Yes
Yes
IEEE 802.1x Open Authentication
Yes
Yes
Yes
IEEE 802.1x with User Distribution
Yes
Yes
Yes
IEEE 802.1x User Port Description
Yes
Yes
Yes
IEEE 802.1x VLAN Assignment)
Yes
Yes
Yes
IEEE 802.1x VLAN User Group Distribution
Yes
Yes
Yes
IEEE 802.1x Wake on LAN
Yes
Yes
Yes
IEEE 802.1x Agentless Audit Support
Yes
Yes
Yes
IEEE 802.1x Authenticator
Yes
Yes
Yes
IEEE 802.1x Fallback support
Yes
Yes
Yes
IEEE 802.1x Guest VLAN
Yes
Yes
Yes
IEEE 802.1x MIB Support
Yes
Yes
Yes
IEEE 802.1x Multi-Domain Auth with Voice VLAN Assignment
Yes
Yes
Yes
IEEE 802.1x Multi-Domain Authentication
Yes
Yes
Yes
13
System Requirements
Table 5
Feature
LAN Base
IP Base
Enterprise
Services
IEEE 802.1x Private Guest VLAN
Yes
Yes
Yes
IEEE 802.1x Private VLAN Assignment
Yes
Yes
Yes
IEEE 802.1x RADIUS Accounting
Yes
Yes
Yes
IEEE 802.1x Radius-Supplied Session Timeout
Yes
Yes
Yes
IEEE 802.1x and MAB with ACL assignment
Yes
Yes
Yes
IEEE 802.3ad Link Aggregation (LACP)
Yes
Yes
Yes
IEEE 802.3ad Link Aggregation (LACP) Port-Channel
Standalone Disable
Yes
Yes
Yes
IEEE 802.3ah and CFM Interworking
No
Yes
Yes
IEEE 802.3x Flow Control
Yes
Yes
Yes
IEEE 802.1x Web-Auth
Yes
Yes
Yes
IGMP Filtering
Yes
Yes
Yes
IGMP Querier
Yes
Yes
Yes
IGMP Snooping
Yes
Yes
Yes
IGMP Version 1
Yes
Yes
Yes
IGMP Version 2
Yes
Yes
Yes
IGMP Version 3
Yes
Yes
Yes
IGMPv3 Host Stack
Yes
Yes
Yes
Ingress Policing
Yes
Yes
Yes
Interface Access (Telnet, Console/Serial, Web)
Yes
Yes
Yes
IOS Based Device Profiling
No
Yes
Yes
IP Enhanced IGRP Route Authentication
No
No
Yes
IP Event Dampening
Yes
Yes
Yes
IP Multicast Load Splitting across Equal-Cost Paths
No
Yes
Yes
IP Named Access Control List
Yes
Yes
Yes
IPv6 Tunnels (in software)
Yes
Yes
Yes
14
System Requirements
Table 5
Feature
LAN Base
IP Base
Enterprise
Services
IP Routing
Yes
Yes
Yes
IP SLAs DHCP Operation
No
Yes
Yes
IP SLAs Distribution of Statistics
No
Yes
Yes
IP SLAs DNS Operation
No
Yes
Yes
IP SLAs FTP Operation
No
Yes
Yes
IP SLAs History Statistics
No
Yes
Yes
IP SLAs HTTP Operation
No
Yes
Yes
IP SLAs ICMP Echo Operation
No
Yes
Yes
IP SLAs ICMP Path Echo Operation
No
Yes
Yes
IP SLAs Multi Operation Scheduler
No
Yes
Yes
IP SLAs One Way Measurement
No
Yes
Yes
IP SLAs Path Jitter Operation
No
Yes
Yes
IP SLAs Random Scheduler
No
Yes
Yes
IP SLAs Reaction Threshold
No
Yes
Yes
IP SLAs Responder
Yes
Yes
Yes
IP SLAs Scheduler
No
Yes
Yes
IP SLAs SNMP Support
No
Yes
Yes
IP SLAs Sub-millisecond Accuracy Improvements
No
Yes
Yes
IP SLAs TCP Connect Operation
No
Yes
Yes
IP SLAs UDP Based VoIP Operation
No
Yes
Yes
IP SLAs UDP Echo Operation
No
Yes
Yes
IP SLAs UDP Jitter Operation
No
Yes
Yes
IP SLAs Video Operations
No
Yes
Yes
IP SLAs VoIP Threshold Traps
No
Yes
Yes
IP Unnumbered for VLAN-SVI interfaces
No
Yes
Yes
IPsecv3/IKEv2 (for management traffic only)
Yes
Yes
Yes
15
System Requirements
Table 5
Feature
LAN Base
IP Base
Enterprise
Services
IPSG (IP Source Guard) v4
Yes
Yes
Yes
IPSG (IP Source Guard) v4 for Static Hosts
Yes
Yes
Yes
IPv4 Policy Based Routing
No
No
Yes
IPv4 Policy Based Routing with recursive next hop
No
No
Yes
IPv6 / v4 BFD with OSPF/ BGP/ EIGRP and Static
No
Yes
Yes
IPv6 Bootstrap Router (BSR) Scoped Zone Support
No
No
Yes
IPv6 First Hop Security (FHS):
Yes
Yes
Yes
Yes
Yes
Yes
IPv6 HSRP
No
Yes
Yes
IPv6 Interface Statistics
Yes
Yes
Yes
IPv6 IP SLAs (UDP Jitter, UDP Echo, ICMP Echo, TCP Connect)
No
Yes
Yes
IPv6 (Internet Protocol Version 6)
Yes
Yes
Yes
IPV6 MLD snooping V1 and V2
Yes
Yes
Yes
IPv6 Multicast
No
Yes
Yes
IPv6 Multicast: Bootstrap Router (BSR)
No
Yes
Yes
IPv6 Multicast: Multicast Listener Discovery (MLD) Protocol,
Versions 1 and 2
No
Yes
Yes
IPv6 Multicast: PIM Accept Register
No
Yes
Yes
DHCPv6 Guard
Lightweight DHCPv6 Relay Agent
IPv6 Destination Guard
IPv6 Snooping
IPv6 Neighbor Discovery Multicast Suppression
IPv6 Router Advertisement (RA) Guard
IPv6 First Hop Security (FHS) Phase 2:
Binding table recovery
Bulk Lease Query support from Lightweight DHCPv6 Relay
Agent (LDRA)
Neighbor Discovery (ND) Multicast Suppress
Source & Prefix Guard3
16
System Requirements
Table 5
Feature
LAN Base
IP Base
Enterprise
Services
IPv6 Multicast: PIM Source-Specific Multicast (PIM-SSM)
No
Yes
Yes
IPv6 Multicast: PIM Sparse Mode (PIM-SM)
No
Yes
Yes
IPv6 Multicast: Routable Address Hello Option
No
Yes
Yes
IPv6 Neighbor Discovery
No
Yes
Yes
IPv6 OSPFv3 Fast Convergence
No
Yes 4
Yes
IPv6 OSPFv3 NSF/SSO
No
Yes 4
Yes
IPv6 Policy Based Routing
No
No
Yes
Identity 4.1 Network Edge Access Topology
Yes
Yes
Yes
IPv6 RA Guard (Host Mode)
Yes
Yes
Yes
IPv6 Reformation
NA
Yes
Yes
IPv6 Routing - EIGRP Support
No
No
Yes
IPv6 Routing: OSPF for IPv6 (OSPFv3)
No
Yes4
Yes
IPv6 Routing: RIP for IPv6 (RIPng)
No
Yes
Yes
IPv6 Static Route support for Object Tracking
Yes
Yes
Yes
IPv6 Switching: CEFv6 Switched Automatic IPv4-compatible
Tunnels (in software)
No
Yes
Yes
IPv6 Switching: CEFv6 Switched Configured IPv6 over IPv4
Tunnels (in software)
No
Yes
Yes
IPv6 Switching: CEFv6 Switched ISATAP Tunnels (in software)
No
Yes
Yes
IPv6 Tunneling: Automatic 6to4 Tunnels (in software)
No
Yes
Yes
IPv6 Tunneling: Automatic IPv4-compatible Tunnels (in
software)
No
Yes
Yes
IPv6 Tunneling: IPv6 over IPv4 GRE Tunnels (in software)
No
Yes
Yes
IPv6 Tunneling: ISATAP Tunnel Support (in software)
No
Yes
Yes
IPv6 Tunneling: Manually Configured IPv6 over IPv4 Tunnels (in
software)
No
Yes
Yes
IPv6 Virtual LAN Access Control List
Yes
Yes
Yes
ISIS for IPv4 and IPv6
No
No
Yes
17
System Requirements
Table 5
Feature
LAN Base
IP Base
Enterprise
Services
ISL Trunk
Yes
Yes
Yes
ISSU (IOS In-Service Software Upgrade)
No
Yes
Yes
Jumbo Frames
Yes
Yes
Yes
Layer 2 Control Packet
Yes
Yes
Yes
Layer 2 Protocol Tunneling (L2PT)
No
Yes
Yes
Layer 2 Traceroute
Yes
Yes
Yes
Layer 3 Multicast Routing (PIM SM, SSM, Bidir)
No
Yes
Yes
Link State Tracking
Yes
Yes
Yes
Local Web Auth
Yes
Yes
Yes
MAB (MAC Authentication Bypass) for Voice VLAN
Yes
Yes
Yes
MAC Address Filtering
Yes
Yes
Yes
MAC Based Access List
Yes
Yes
Yes
MAC Move and Replace
Yes
Yes
Yes
Medianet 2.0: AutoQoS SRND4 Macro
No
Yes
Yes
Medianet 2.0: Integrated Video Traffic Simulator
(hardware-assisted IP SLA); IPSLA responder only
No
Yes
Yes
Medianet 2.0: Flow Metadata
No
Yes
Yes
Medianet 2.0: Media Service Proxy
No
Yes
Yes
Medianet 2.0: Media Monitoring (Performance Monitoring and
Mediatrace)
No
Yes
Yes
Medianet 2.0: MSP and Metadata
No
No
Yes
MediaTrace 1.0
Yes
Yes
Yes
Multicast BGP (MBGP)
No
No
Yes
Multicast HA (NSF/SSO) for IPv4&IPv6
No
Yes
Yes
Multicast Routing Monitor (MRM)
No
Yes
Yes
Multicast Source Discovery Protocol (MSDP)
Yes
Yes
Yes
Multicast VLAN Registration (MVR)
Yes
Yes
Yes
18
System Requirements
Table 5
Feature
LAN Base
IP Base
Enterprise
Services
Multi-authentication and VLAN Assignment
Yes
Yes
Yes
Multi-VRF Support (VRF lite)
No
No
Yes
NAC - L2 IEEE 802.1x
Yes
Yes
Yes
NAC - L2 IP
Yes
Yes
Yes
ND Cache Limit/Interface
No
Yes
Yes
NEAT Enhancement: Re-Enabling BPDU Guard Based on User
Configuration
Yes
Yes
Yes
Network Edge Access Topology (NEAT)
Yes
Yes
Yes
Network Time Protocol (NTP)
Yes
Yes
Yes
NMSP Enhancements
No
Yes
Yes
Time Protocols (SNTP, TimeP) master
Yes
Yes
Yes
No. of QoS Filters
Yes (4K entries)
Yes
Yes
No Service Password Recovery
Yes
Yes
Yes
No. of VLAN Support
2048
4096
4096
NSF - BGP
No
No
Yes
NSF - EIGRP
No
Yes
Yes
NSF - OSPF (version 2 only)
No
Yes
Yes
NSF/SSO (Nonstop Forwarding with Stateful Switchover)
No
No
Yes
NTP for IPv6
Yes
Yes
Yes
NTP for VRF aware
No
No
Yes
On Demand Routing (ODR)
No
No
Yes
OSPF
No
Yes4
Yes
•
GPS support for location
•
Location at switch level
•
Local timezone change
•
Name value pair
•
Priority settings for MIBs
No. of Security ACE
19
System Requirements
Table 5
Feature
LAN Base
IP Base
Enterprise
Services
OSPF v3 Authentication
No
Yes4
Yes
OSPFv3 Authentication Trailer
Yes
Yes
Yes
OSPF Flooding Reduction
No
Yes4
Yes
OSPF for Routed Access5
No
Yes
Yes
OSPF Incremental Shortest Path First (i-SPF) Support
No
Yes4
Yes
OSPF Link State Database Overload Protection
No
Yes4
Yes
OSPF Not-So-Stubby Areas (NSSA)
No
Yes4
Yes
OSPF Packet Pacing
No
Yes4
Yes
OSPF Shortest Paths First Throttling
No
Yes4
Yes
OSPF Stub Router Advertisement
No
Yes4
Yes
OSPF Support for Fast Hellos
No
Yes4
Yes
OSPF Support for Link State Advertisement (LSA) Throttling
No
Yes4
Yes
OSPF Support for Multi-VRF on CE Routers
No
Yes4
Yes
OSPF Update Packet-Pacing Configurable Timers
No
Yes4
Yes
Out-of-band Management Port
Yes
Yes
Yes
Out-of-band Management Port - IPv6
Yes
Yes
Yes
PAgP
Yes
Yes
Yes
Passwords
Password clear protection
Yes
Yes
Yes
PBR Support for Multiple Tracking Options
Yes
Yes
Yes
Per Intf IGMP State Limit
Yes
Yes
Yes
Per Intf MrouteState Limit
Yes
Yes
Yes
Per-User ACL Support for 802.1X/MAB/Webauth users
Yes
Yes
Yes
Per-VLAN Learning
Yes
Yes
Yes
PIM Sparse Mode Version4
No
No
Yes
PIM Version 1
No
Yes
Yes
20
System Requirements
Table 5
Feature
LAN Base
IP Base
Enterprise
Services
PM Version 2
No
Yes
Yes
PoE (up to 15.4W only)
Yes
Yes
Yes
PoE+ Ready
Yes
Yes
Yes
PoEP via LLDP
Yes
Yes
Yes
Port Access Control List (PACL)
Yes
Yes
Yes
Port Monitoring (interface Stats)
Yes
Yes
Yes
Port Security
Yes (supports
1024 MACs)
Yes (supports
3072 MACs)
Yes (supports
3072 MACs)s
Post Status
Yes
Yes
Yes
Pragmatic General Multicast (PGM)
Yes
Yes
Yes
Private VLANs
Yes
Yes
Yes
Propagation of Location Info over CDP
Yes
Yes
Yes
PVLAN over EtherChannel
Yes
Yes
Yes
PVST+ (Per Vlan Spanning Tree Plus)
Yes
Yes
Yes
Q-in-Q
Yes
Yes
Yes
RACL
Yes
Yes
Yes
RADIUS/TACACS+ (AAA)
Yes
Yes
Yes
RADIUS Attribute 44 (Accounting Session ID) in Access
Requests
Yes
Yes
Yes
RADIUS Change of Authorization
Yes
Yes
Yes
Rapid-Per-VLAN-Spanning Tree (Rapid-PVST)
Yes
Yes
Yes
Remote SPAN (RSPAN)
Yes
Yes
Yes
REP (Resilient Ethernet Protocol)
Yes
Yes
Yes
REP - No Edge Neighbor Enhancement
Yes
Yes
Yes
RIP v1
No
Yes
Yes
RMON
Yes
Yes
Yes
Role-Based Access Control CLI commands (RBAC)
Yes
Yes
Yes
21
System Requirements
Table 5
Feature
LAN Base
IP Base
Enterprise
Services
Role-Based CLI Inclusive Views
Yes
Yes
Yes
RPR
Yes
Yes
Yes
RPVST+
Yes
Yes
Yes
RSPAN
Yes
Yes
Yes
Secure CDP
Yes
Yes
Yes
Secure Copy (SCP)
Yes
Yes
Yes
Secure Shell SSH Version 1, 2 Server Support
Yes
Yes
Yes
Secure Shell SSH Version 1, 2 Client Support
Yes
Yes
Yes
Service Advertisement Framework (SAF)
No
No
Yes
Smart Install Director—Configuration-only Deployment and
Smooth Upgrade
Yes
Yes
Yes
SmartPorts (Role based MACRO)
Yes
Yes
Yes
SMI Catalyst 4K Client
Yes
Yes
Yes
SNMP (Simple Network Management Protocol)
Yes
Yes
Yes
SNMPv3 (SNMP Version 3)
Yes
Yes
Yes
Source Port Filtering (Private VLAN)
Yes
Yes
Yes
Source Specific Multicast (SSM)
No
Yes
Yes
Source Specific Multicast (SSM) - IGMPv3,IGMP v3lite, and
URD
Yes
Yes
Yes
Source Specific Multicast (SSM) Mapping
Yes
Yes
Yes
SPAN (# of sessions) – Port Mirroring
Yes (2
bidirectional
sessions)
Yes (8
bidirectional
sessions)
Yes (8
bidirectional
sessions)
SPAN ACL Filtering for IPv6
Yes
Yes
Yes
SSHv2/Secure Copy, FTP, SSL, Syslog, Sys Information
Yes
Yes
Yes
SSO (Stateful SwitchOver)
No
Yes
Yes
Static Route Support for BFD over IPv6
No
No
Yes
Static Routing (IPv4/IPv6)
Yes
Yes
Yes
22
System Requirements
Table 5
Feature
LAN Base
IP Base
Enterprise
Services
Storm Control - Per-Port Multicast Suppression
Yes
Yes
Yes
Stub IP Multicast Routing
No
Yes
No
Sub-second UDLD
Yes
Yes
Yes
SVI (Switch Virtual Interface) Autostate Exclude
Yes
Yes
Yes
TACACS+
Yes
Yes
Yes
TACACS+ and Radius for IPv6-
Yes
Yes
Yes
Time-Based Access Lists
Yes
Yes
Yes
Time Domain Reflectometry (TDR)6
No
Yes
Yes
Time Protocols (SNTP, TimeP)
Yes
Yes
Yes
Traffic Mirroring (SPAN)
Yes
Yes
Yes
Trusted Boundary (LLDP & CDP Based)
Yes
Yes
Yes
TrustSec SGT/ SGA
No
Yes
Yes
Unicast Reverse Path Forwarding (uRPF)
Yes
Yes
Yes
UniDirectional Link Detection (UDLD)
Yes
Yes
Yes
Virtual Router Redundancy Protocol (VRRP) for IPv4
No
Yes
Yes
VLAN Access Control List (VACL)
Yes
Yes
Yes
VLAN Mapping (VLAN Translation)
No
Yes
Yes
Voice VLAN
Yes
Yes
Yes
VRF-aware TACACS+
No
No
Yes
VRF-lite for IPv6 on OSPF/ BGP/ EIGRP
No
No
Yes
VTP (Virtual Trunking Protocol) Version 2
Yes
Yes
Yes
VTP version 3
Yes
Yes
Yes
WCCP Redirection on Inbound Interfaces
No
Yes
Yes
WCCP Version 2
No
Yes
Yes
WSMA Enhancements for wireless management
Yes
Yes
Yes
TrustSec
23
System Requirements
Table 5
Feature
LAN Base
IP Base
Enterprise
Services
XML-PI
Yes
Yes
Yes
1. Supported only on Supervisor Engine 6-E and Supervisor Engine 6L2. Starting with Cisco IOS Release 12.2(46)SG
3. When either Source or Prefix Guard for IPv6 is enabled, ICMPv6 packets are unrestricted on all Catalyst 4500 series switch platforms running IOS Cisco
Release 15.2(1)E. All other traffic types are restricted.
4. IP Base supports only one OSPFv2 and one OSPFv3 instance with a maximum number of 200 dynamically learned routes.
5. OSPF for Routed Access supports only one OSPFv2 and one OSPFv3 instance with a maximum number of 1000 dynamically learned routes.
6. TDR is not supported on 46xx linecards.
Note
You can purchase a special license to enable the 10 Gigabit uplinks in the LAN Base image without
moving to IP Base.
MIB Support
For information on MIB support, please refer to this URL:
ftp://ftp.cisco.com/pub/mibs/supportlists/cat4000/cat4000-supportlist.html
Features Not Supported on the Cisco Catalyst 4500 Series Switch
•
BFD for IPv6 EIGRP and IPv6 BGP in any 3.4.0SG images including SG4 (to be released in
May-June, 2014).
•
The following ACL types:
– Standard Xerox Network System (XNS) access list
– Extended XNS access list
– DECnet access list
– Protocol type-code access list
•
ADSL and Dial access for IPv6
•
AppleTalk EIGRP
•
Bridge groups
•
CEF Accounting
•
CFM CoS
•
Cisco IOS software IPX ACLs:
– <1200-1299>
IPX summary address access list
•
Cisco IOS software-based transparent bridging (also called “fallback bridging”)
•
Connectionless (CLNS) routing; including IS-IS routing for CLNS. IS-IS is supported for IP routing
only.
24
System Requirements
•
DLSw (data-link switching)
•
IGRP (use EIGRP instead)
•
isis network point-to-point command
•
Kerberos support for access control
•
LLDP HA
•
Lock and key
•
NAT-PT for IPv6
•
NetFlow per-VRF
•
PBR with EOT
•
PBR with Multiple Tracking Options
•
QoS for IPv6 traffic (only supported on Supervisor 6)
•
Reflexive ACLs
•
Routing IPv6 over an MPLS network
•
SMI Proxy
•
WCCP version 1
Orderable Product Numbers
Table 6
Orderable Product Numbers for the Catalyst 4500 Series Switch
Product Number
Description
Image
S45EES-15202E
Cisco CAT4500E IOS ENTERPRISE SERVICES
W/O CRYPTO
cat4500e-entservices-mz
S45EESU-15202E
UPGRADE W/O CRYPTO
cat4500e-entservices-mz
S45EESK9-15202E
SSH
cat4500e-entservicesk9-mz
S45EESUK9-15202E
UPGRADE SSH
cat4500e-entservicesk9-mz
S45EIPB-15202E
Cisco CAT4500E IOS IP BASE W/O CRYPTO
cat4500e-ipbase-mz
S45EIPBU-15202E
Cisco CAT4500E IOS IP BASE UPGRADE W/O
CRYPTO
cat4500e-ipbase-mz
S45EIPBK9-15202E
Cisco CAT4500E IOS IP BASE SSH
cat4500e-ipbasek9-mz
S45EIPBUK9-15202E
Cisco CAT4500E IOS IP BASE UPGRADE SSH
cat4500e-ipbasek9-mz
S45ELB-15202E
Cisco CAT4500E IOS LAN BASE W/O CRYPTO
cat4500e-lanbase-mz
S45ELBK9-15202E
Cisco CAT4500E IOS LAN BASE SSH
cat4500e-lanbasek9-mz
25
New and Changed Information
These sections describe the new and changed information for the Catalyst 4500 series switch running
Cisco IOS software:
•
New Software Features in Release 15.2(2)E3, page 26
•
New Hardware Features in Release 15.2(2)E1, page 26
•
New Software Features in IOS Release 15.2(2)E1, page 27
•
New Software Features in Release IOS 15.2(2)E, page 27
New Software Features in Release 15.2(2)E3
The following table list the new features for Release IOS 15.2(2)E3:
Feature Name
Description
CDP Bypass
Authentication sessions are established in single and multi-host modes for IP Phones.
However, if voice VLAN and 802.1x on an interface port is enabled, then CDP Bypass is
enabled when the host mode is set to single or multi-host mode.
Note
By default the host mode is set to single mode in legacy mode and
multi-authentication in the eedge mode.
Use the following commands to configure CDP bypass:
Switch> enable
Switch# configure terminal
Switch(config)# interface < interface-id >
Switch(config-if)# switchport mode access
Switch(config-if)# switchport voice vlan < vlan-id >
Switch(config-if)# authentication port-control auto
Switch(config-if)# authentication host-mode {single | multi-host}
Switch(config-if)# dot1x pae authenticator
(LAN Base, IP Base, and Enterprise Services)
New Hardware Features in Release 15.2(2)E1
•
New passive CX1 assemblies: SFP-H10GB-CU1-5M, SFP-H10GB-CU2M, SFP-H10GB-CU2-5M
•
Support for SFP-H10GB-ACU7M, SFP-H10GB-ACU10M (active CX1 cable assemblies)
•
Support of breakout cable on the 10 GbE end for: QSFP-4SFP10G-CU1M, QSFP-4SFP10G-CU3M,
QSFP-4SFP10G-CU5M
•
Support for Cisco SFP+ Active Optical Cables - Cisco SFP-10G-AOC1M Cisco SFP-10G-AOC2M
Cisco SFP-10G-AOC3M, Cisco SFP-10G-AOC5M, Cisco SFP-10G-AOC7M, Cisco
SFP-10G-AOC10M
26
New Software Features in IOS Release 15.2(2)E1
The following table list the new features for Release IOS 15.2(2)E1.
Feature Name
Description
Device Sensor
(LAN Base)
Policy Based Routing (IP Base)
(PBR)
New Software Features in Release IOS 15.2(2)E
The following table list the new features for Release IOS 15.2(2)E.
Feature Name
Description
Provides quick and easy access to all relevant documentation for specific platforms. Look
Use this URL for the for Quick Links to Platform Documentation on the respective platform documentation
Cisco IOS XE Release pages.
3E Documentation
· http://www.cisco.com/c/en/us/support/ios-nx-os-software/ios-xe-3e/tsd-pr
Roadmap
oducts-support-series-home.html
Use this URL for the
Cisco IOS Release
15E Documentation
Roadmap
·
:
http://www.cisco.com/c/en/us/support/ios-nx-os-software/ios-15-2e/tsd
-products-support-series-home.html
Auto Security
Provides a single line CLI, to enable base line security features (Port Security, DHCP
snooping, DAI).
DHCP Gleaning
Allows components to register and glean DHCP packets.This is a read--only DHCP
functionality.
Embedded Event
Manager (EEM) 4.0
Provides unique customization capabilities and event driven automation within Cisco
products.
HSRP: Global IPv6
Address
Allows users to configure multiple non-link local addresses as virtual addresses. The Hot
Standby Router Protocol (HSRP) ensures host-to-router resilience and failover, in case
the path between a host and the first-hop router fails, or the first-hop router itself fails.
IPv6 Static Route
support for Object
Tracking
Allows an IPv6 Static Route to be associated with a tracked-object.
IPv6 PBR
Allows you to manually configure how the received packets should be routed. PBR allows
you to identify packets by using several attributes and to specify the next hop or the
output interface to which the packet should be sent.
Note
With IOS XE Release 3.6.0E and IOS 15.2(2)E, IPv6 PBR is not supported on
Supervisor Engine 8-E.
27
Upgrading the System Software
Feature Name
Description
MediaTrace 1.0
Provides the capability to diagnose Media Stream on top of various instrumentations in
Cisco routers/switches and endpoints. Also addresses the MediaNet Video monitoring
requirement to discover the signaling path and provides end-to-end diagnostics along the
media stream routes
OSPFv3
Provides a mechanism to authenticate Open Shortest Path First version 3 (OSPFv3)
Authentication Trailer protocol packets as an alternative to existing OSPFv3 IPsec authentication.
PBR Support for
Multiple Tracking
Options
Extends the capabilities of object tracking using Cisco Discovery Protocol (CDP) to
allow the policy-based routing (PBR) process to verify object availability by using
additional methods.
Role-Based CLI
Inclusive Views
Enables a standard CLI view including all commands by default.
Policy Based Routing: Enhances route maps to enable configuration of a recursive next-hop IP address that is
Recursive Next Hop
used by policy-based routing (PBR).
Secure CDP
Allows you to select the type, length, value (TLV) fields that are sent on a particular
interface to filter information sent through Cisco Discovery Protocol packets.
SMI Catalyst 4K
Client
Enables a Catalyst 4k standalone switch acting as Smart Install Client.
Note
SMI Proxy is supported.
WSMA
Allows you to reduce the reconnecting rates in an outage when device connections to the
Enhancements for
management server on wireless networks are disconnected unexpectedly.
wireless management
In most cases, upgrading the switch to a newer release of Cisco IOS software does not require a
ROMMON upgrade. However, if you are running an early release of Cisco IOS software and plan to
upgrade, refer to the following tables for the minimum Cisco IOS image and the recommended
ROMMON release, respectively.
Note
You must upgrade to at least ROMMON Release 12.2(44r)SG5 to run Cisco IOS Release 15.1(2)SG on
the Supervisor Engine 6-E and Supervisor Engine 6L-E. 12.2(44r)SG9 is recommended.
Caution
Most supervisor engines have the required ROMMON release. However, due to caveat CSCed25996, we
recommend that you upgrade your ROMMON to the recommended release.
Table 7
Supervisor Engine and Recommended ROMMON Release
Supervisor Engine
Recommended
ROMMON Release
6-E
12.2(44r)SG9
6L-E
12.2(44r)SG9
28
Table 8
ROMMON Release and Promupgrade Programs
ROMMON Release Promupgrade Program
12.2(31r)SGA4
cat4500-e-ios-promupgrade-122_31r_SGA4
12.2(44r)SG5
cat4500-e-ios-promupgrade-122_44r_SG5
12.2(44r)SG9
12.2(44r)SG10
The following sections describe how to upgrade your switch software:
•
Identifying an +E Chassis and ROMMON, page 29
•
Upgrading the Cisco IOS Software, page 29
Identifying an +E Chassis and ROMMON
An +E chassis is identified by a FRU minor value in the chassis' idprom.
When supervisor engine 1 (sup1) is in ROMMON and supervisor engine 2 (sup2) is in IOS, only sup2
can read the idprom contents of chassis’ idprom. Chassis type is displayed as “+E” in the output of the
show version command. Conversely, sup1 can only display the chassis type as “E.”
When both sup1 and sup2 are in ROMMON, both engines can read the chassis’ idprom. Chassis type is
displayed correctly as “+E” in the output of the show version command.
When both sup1 and sup2 are in IOS, both engines can read the chassis’ idprom. Chassis type is
displayed correctly as “+E” in the output of the show version command.
Upgrading the Cisco IOS Software
Caution
To avoid actions that might make your system unable to boot, please read this entire section before
starting the upgrade.
Before you proceed, observe the following rules for hostname:
•
Do not expect case to be preserved
Uppercase and lowercase characters look the same to many internet software applications. It may
seem appropriate to capitalize a name the same way you might do in English, but conventions dictate
that computer names appear all lowercase. For more information, refer to RFC 1178, Choosing a
Name for Your Computer.
•
Must start with a letter and end with a letter or digit.
•
Interior characters can only be letters, digits, and hyphens; periods and underscores not allowed.
•
Names must be 63 characters or fewer; hostname of fewer than 10 characters is recommended.
•
On most systems, a field of 30 characters is used for the host name and the prompt in the CLI. Longer
configuration mode prompts may be truncated.
29
To upgrade the Cisco IOS software on your Catalyst 4500 series switch, use this procedure:
Step 1
Download Cisco IOS Release 15.1(2)SG from Cisco.com, and place the image on a TFTP server in a
directory that is accessible from the supervisor engine that is upgraded.
Step 2
Use the dir bootflash: command to ensure that there is sufficient space in Flash memory to store the
promupgrade image. If there is insufficient space, delete one or more images, and then enter the
squeeze bootflash: command to reclaim the space.
If you are using a CompactFlash card, use slot0: instead of bootflash.
Step 3
Download the software image into Flash memory using the copy tftp command.
The following example shows how to download the Cisco IOS software image
cat4000-is-mz.121-12c.EW from the remote host 172.20.58.78 to bootflash:
Switch# copy tftp: bootflash:
Address or name of remote host [172.20.58.78]?
Source filename [cat4000-is-mz121_12c.EW]?
Destination filename [cat4000-is-mz.121-12c.EW]?
Accessing tftp://172.20.58.78/cat4000-is-mz.121-12c.EW...
Loading cat4000-is-mz.121-12c.EW from 172.20.58.78 (via
FastEthernet2/1):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
|!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK - 6923388/13846528 bytes]
6923388 bytes copied in 72.200 secs (96158 bytes/sec)
Switch#
Step 4
Use the no boot system flash bootflash:file_name command to clear the cat4000-is-mz.121-8a.EW file
and to save the BOOT variable.
The following example shows how to clear the BOOT variable:
Switch(config)# no boot system flash bootflash:cat4000-is-mz.121-8a.EW
Switch(config)# exit
Switch# write
Building configuration...
Compressed configuration from 3641 to 1244 bytes [OK]
Switch#
Step 5
Use the boot system flash command to add the Cisco IOS software image to the BOOT variable.
The following example shows how to add the cat4000-is-mz.121-12c.EW image to the BOOT variable:
Switch(config)# boot system flash bootflash:cat4000-is-mz.121-12c.EW
Switch# write
30
Switch#
Step 6
Use the config-register command to set the configuration register to 0x2102.
The following example show how to set the second least significant bit in the configuration register:
Switch(config)# config-register 0x2102
Switch# write
Switch#
Step 7
Caution
Enter the reload command to reset the switch and load the software.
No intervention is necessary to complete the upgrade. To ensure a successful upgrade, do not interrupt
the upgrade process by performing a reset, power cycle, or OIR of the supervisor, for at least five
minutes.
The following example shows the output from a successful upgrade followed by a system reset:
Switch# reload
Rommon reg: 0x2B004180
Upgrading FPGA...
Decompressing the image
############## [OK]
*******************************************************
*
*
* WS-X4014 FPGA Upgrade Utility For WS-X4014 Machines *
*
*
* Copyright (c) 2002 by Cisco Systems, Inc.
*
* All rights reserved.
*
*
*
**********************************************************
Image size = 483.944 KBytes
Maximum allowed size = 1023.75 KBytes
Upgrading your FPGA image... DO NOT RESET the system
unless instructed or upgrade of FPGA will fail !!!
Beginning erase of 0x100000 bytes at offset 0x3d00000...
Beginning write of fpga image
Done!
(0x78fb0 bytes at offset 0x3d00000)...
This could take as little as 30 seconds or up to 2 minutes.
Please DO NOT RESET!
Success! FPGA image has been upgraded successfully.
System will reset itself and reboot in about 15 seconds.
0
31
Limitations and Restrictions
**********************************************************
*
*
* Welcome to Rom Monitor for WS-X4014 System.
*
* Copyright (c) 2002 by Cisco Systems, Inc.
*
* All rights reserved.
*
*
*
**********************************************************
Rom Monitor Program Version 12.1(12r)EW
Board type 1, Board revision 5
Swamp FPGA revision 16, Dagobah FPGA revision 47
MAC Address
IP Address
Netmask
Gateway
TftpServer
Main Memory
:
:
:
:
:
:
00-30-85-XX-XX-XX
10.10.10.91
255.255.255.0
10.10.10.1
Not set.
256 MBytes
***** The system will autoboot in 5 seconds *****
Type control-C to prevent autobooting.
Switch#
Step 8
Use the show version command to verify that the new Cisco IOS release is operating on the switch.
These sections list the limitations and restrictions for the current release of Cisco IOS software on the
Catalyst 4500 series switch.
•
The show exception files all command lists only crashinfo files from the active supervisor engine.
You must issue the dir slavecrashinfo: and dir slvecrashinfo-dc: commands to obtain lists of
crashinfo files from the standby supervisor engine.
•
Starting with Release IOS 15.1(1)SG, the seven RP restriction was removed.
•
A Span destination of fa1 is not supported.
•
The "keepalive" CLI is not supported in interface mode on the switch, although it will appear in the
running configuration. This behavior has no impact on functionality.
•
TDR is only supported on interfaces Gi1/1 through Gi1/48, at 1000BaseT under open or shorted
cable conditions. TDR length resolution is +/- 10 m. If the cable is less than 10 m or if the cable is
properly terminated, the TDR result displays "0" m. If the interface speed is not 1000BaseT, an
"unsupported" result status displays. TDR results will be unreliable for cables extended with the use
of jack panels or patch panels.
•
The following guidelines apply to Fast UDLD:
– Fast UDLD is disabled by default.
– Configure fast UDLD only on point-to-point links between network devices that support fast
UDLD.
– You can configure fast UDLD in either normal or aggressive mode.
32
– Do not enter the link debounce command on fast UDLD ports.
– Configure fast UDLD on at least two links between each connected network device. This
reduces the likelihood of fast UDLD incorrectly error disabling a link due to false positives.
– Fast UDLD does not report a unidirectional link if the same error occurs simultaneously on
more than one link to the same neighbor device.
•
A XML-PI specification file entry does not return the desired CLI output.
The outputs of certain commands, such as show ip route and show access-lists, contain
non-deterministic text. While the output is easily understood, the output text does not contain strings
that are consistently output. A general purpose specification file entry is unable to parse all possible
output.
Workaround (1):
While a general purpose specification file entry may not be possible, a specification file entry might
be created that returns the desired text by searching for text that is guaranteed to be in the output. If
a string is guaranteed to be in the output, it can be used for parsing.
For example, the output of the show ip access-lists SecWiz_Gi3_17_out_ip command is this:
Extended IP access list SecWiz_Gi3_17_out_ip
10 deny ip 76.0.0.0 0.255.255.255 host 65.65.66.67
20 deny ip 76.0.0.0 0.255.255.255 host 44.45.46.47
30 permit ip 76.0.0.0 0.255.255.255 host 55.56.57.57
The first line is easily parsed because access list is guaranteed to be in the output:
<Property name="access list" alias="Name" distance="1.0" length="-1" type="String"
/>
The remaining lines all contain the term host. As a result, the specification file may report the
desired values by specifying that string. For example, this line
<Property name="host" alias="rule" distance="s.1" length="1" type="String" />
will produce the following for the first and second rules
<rule>
deny
</rule>
and the following for the third statement
<rule>
permit
<rule>
Workaround (2):
Request the output of the show running-config command using NETCONF and parse that output
for the desired strings. This is useful when the desired lines contain nothing in common. For
example, the rules in this access list do not contain a common string and the order (three permits,
then a deny, then another permit), prevent the spec file entry from using permit as a search string,
as in the following example:
Extended MAC access list MACCOY
permit 0000.0000.ffef ffff.ffff.0000 0000.00af.bcef ffff.ff00.0000 appletalk
permit any host 65de.edfe.fefe xns-idp
permit any any protocol-family rarp-non-ipv4
deny
host 005e.1e5d.9f7d host 3399.e3e1.ff2c dec-spanning
permit any any
33
The XML output of show running-config command includes the following, which can then be
parsed programmatically, as desired:
<mac><access-list><extended><ACLName>MACCOY</ACLName></extended></access-list></mac>
<X-Interface> permit 0000.0000.ffef ffff.ffff.0000 0000.00af.bcef ffff.ff00.0000
appletalk</X-Interface>
<X-Interface> permit any host 65de.edfe.fefe xns-idp</X-Interface>
<X-Interface> permit any any protocol-family rarp-non-ipv4</X-Interface>
<X-Interface> deny
host 005e.1e5d.9f7d host 3399.e3e1.ff2c
dec-spanning</X-Interface>
<X-Interface> permit any any</X-Interface>
•
Although the Catalyst 4500 series switch still supports legacy 802.1X commands used in Cisco IOS
Release 12.2(46)SG and earlier releases (that is, they are accepted on the CLI), they do not display
in the CLI help menu.
•
Current IOS software cannot support filenames exceeding 64 characters.
•
All software releases support a maximum of 32,768 IGMP snooping group entries.
•
Although you can configure subsecond PIM query intervals on Catalyst 4500 platforms, such an
action represents a compromise between convergence (reaction time) and a number of other factors
(number of mroutes, base line of CPU utilization, CPU speed, processing overhead per 1 m-route,
etc.). You must account for those factors when configuring subsecond PIM timers. We recommend
that you set the PIM query interval to a minimum of 2 seconds. By adjusting the available
parameters, you can achieve flawless operation; that is, a top number of multicast routes per given
convergence time on a specific setup.
•
With Cisco IOS Release XE 3.2.1SG, memory configuration is enabled:
Switch(config)# memory ?
chunk
chunk related configuration
free
free memory low water mark
record
configure memory event/traceback recording options
reserve reserve memory
sanity
Enable memory sanity
This configuration had been removed erroneously in a prior release.
•
The Catalyst 4510R switch does not support Supervisor Engines 6L-E. Installing an unsupported
supervisor engine causes unpredictable hardware behavior that cannot be controlled by the software.
Using an unsupported supervisor engine in a redundant slot might cause a supported supervisor
engine in the other slot to malfunction.
•
The MAC address table is cleared while you switch between supervisor engines if either the 802.1s
or 802.1w Spanning Tree Protocol is configured. To minimize address clearing and subsequent
packet flooding, configure the edge ports as spanning-tree portfast and the link type as
spanning-tree link-type point-to-point.
•
IP classful routing is not supported; do not use the no ip classless command; it will have no effect,
because only classless routing is supported. The command ip classless is not supported because
classless routing is enabled by default.
•
A Layer 2 LACP channel cannot be configured with the spanning tree PortFast feature.
•
Netbooting using a boot loader image is not supported.
•
When you deploy redundant supervisors in a Catalyst 4507R, for hardware that does not exist while
the startup configuration file is being parsed, the configuration file for the hardware is not applied.
34
For example, if the active supervisor engine is in slot 1, and you have configured interface Gi1/1,
the supervisor engine in slot 2 becomes active if you remove the active supervisor engine from the
chassis. In addition, while the startup configuration file is being parsed, you will receive an error
message indicating that interface Gi1/1 is no longer present. This behavior is correct. When the
formerly active supervisor engine is reinserted into slot 1, there is no configuration for interface
Gi1/1.
This situation will not occur when both supervisor engines are physically in the chassis.
Workaround: Copy the startup configuration file into the running configuration:
Switch# copy startup-config running-config
•
An unsupported default CLI for mobile IP is displayed in the HSRP configuration. Although this
CLI will not harm your system, you might want to remove it to avoid confusion.
Workaround: Display the configuration with the show standby command, then remove the CLI.
Here is an example of show standby GigabitEthernet1/1 command output:
switch(config)# interface g1/1
switch(config)# no standby 0 name (0 is hsrp group number)
•
For HSRP preempt delay to function consistently, you must use the standby delay minimum
command. Be sure to set the delay to more than 1 hello interval, thereby ensuring that a hello is
received before HSRP leaves the initiate state.
Use the standby delay reload option if the router is rebooting after reloading the image.
•
When you attempt to run OSPF between a Cisco router and a third party router, the two interfaces
might get stuck in the Exstart/Exchange state. This problem occurs when the maximum transmission
unit (MTU) settings for neighboring router interfaces do not match. If the router with the higher
MTU sends a packet larger than the MTU set on the neighboring router, the neighboring router
ignores the packet.
Workaround: Ensure that the MTUs match.
•
You can run only .1q-in-.1q packet pass-through with Supervisor Engine 6-E.
•
For PVST and Catalyst 4500 E-Series switch VLAN, Cisco IOS Release 12.1(13)EW support a
maximum of 3000 spanning tree port instances. If you want to use more instances, use MST rather
than PVST.
•
Because the Supervisor Engine 6-E supports the FAT filesystem, the following restrictions apply:
– The verify and squeeze commands are not supported.
– The rename command is supported in FAT file system.
For Supervisor Engine 6-E, the rename command is available for bootflash and slot0. For all
other supervisor engines, the rename command is supported for nvram devices only.
– The fsck command is supported for slot0 device. It is not supported in the file systems on
supervisor engines other than 6-E.
– In the FAT file system, the IOS format bootflash: command erases user files only. It does not
erase system configuration.
– The FAT file system supports a maximum of 63 characters for file/directory name. The
maximum for path length is 127 characters.
– The FAT file system does not support the following characters in file/directory names:{}#%^
and space characters.
– The FAT file system honors the Microsoft Windows file attribute of read-only and read-write,
but it does not support the Windows file hidden attribute.
35
– Supervisor Engine 6-E uses the FAT file system for compact flash (slot0). If a compact flash is
not formatted in FAT file system (such as compact flash on a supervisor engine other than 6-E),
the switch does not recognize it.
•
If an original packet is dropped because of transmit queue shaping or sharing configurations, a
SPAN packet copy can still be transmitted on the SPAN port.
•
All software releases support a maximum of 16,000 IGMP snooping group entries.
•
To maximize performance, use the no ip unreachables command on all interfaces that are
configured for ACLs.
•
The threshold for the Dynamic Arp Inspection err-disable function is set to 15 ARP packets per
second per interface. You should adjust this threshold depending on the network configuration. The
CPU should not receive DHCP packets at a sustained rate greater than 1000 pps.
•
If you first configure an IP address or IPv6 address on a Layer 3 port, then change the Layer 3 port
to a Layer 2 port with the switchport command, and finally change it back to a Layer 3 port, the
original IP/IPv6 address is lost.
•
In a redundant system, do not remove and reinsert the standby supervisor engine while the active
supervisor engine is booting. Doing so may cause the online diagnostics test to fail.
Workaround: Remove and reinsert the standby supervisor engine after the active supervisor engine
boots. (CSCsa66509)
•
The switchport private-vlan mapping trunk command supports a maximum of 500 unique private
VLAN pairs. For example, 500 secondary VLANs could map to one primary VLAN, or 500
secondary VLANs could map to 500 primary VLANs.
•
Support for PoE depends on the use of the following line cards and power supplies.
PoE switching modules:
– WS-X4148-RJ45V
– WS-X4224-RJ45V
– WS-X4248-RJ45V
– WS-X4248-RJ21V
– WS-X4524-GB-RJ45V
– WS-X4548-GB-RJ45V
– WS-X4648-RJ45V-E
– WS-X4648-RJ45V+E
– WS-X4548-GB-RJ45V+
PoE enabled power supplies:
– PWR-C45-1300ACV
– PWR-C45-1400DC
– PWR-C4K-2800AC
– PWR-C45-1300ACV
– PWR-C45-6000ACV
•
If a Catalyst 4500 series switch requests information from the Cisco Secure Access Control Server
(ACS) and the message exchange times out because the server does not respond, a message similar
to this appears:
36
00:02:57: %RADIUS-4-RADIUS_DEAD: RADIUS server 172.20.246.206:1645,1646 is not
responding.
If this message appears, ensure network connectivity exists between the switch and the ACS. Also
check that the switch has been properly configured as an AAA client on the ACS.
•
For IP Port Security (IPSG) for static hosts, the following apply:
– As IPSG learns the static hosts on each interface, the switch CPU may achieve 100 percent if
there are a large number of hosts to learn. The CPU usage will drop after the hosts are learned.
– IPSG violations for static hosts are printed as they occur. If multiple violations occur
simultaneously on different interfaces, the CLI displays the last violation. For example, if IPSG
is configured for 10 ports and violations exist on ports 3,6, and 9, the violation messages are
printed only for port 9.
– Inactive host bindings will appear in the device tracking table when either a VLAN is associated
with another port or a port is removed from a VLAN. So, as hosts are moved across subnets, the
hosts appear in the device tracking table as inactive.
– Autostate SVI does not work on EtherChannel.
•
When IPv6 is enabled on an interface with any CLI, you might see the following message:
% Hardware MTU table exhausted
In such a scenario, the IPv6 MTU value programmed in hardware differs from the IPv6 interface
MTU value. This occurs if no room exists in the hardware MTU table to store additional values.
To create room, unconfigure some unused MTU values. Then, either disable or re-enable IPv6 on
the interface, or reapply the MTU configuration.
•
To stop IPSG with static hosts on an interface, use the following commands in interface
configuration submode:
Switch(config-if)# no ip verify source
Switch(config-if)# no ip device tracking max
To enable IPSG with static hosts on a port, enter the following commands:
Switch(config)# ip device tracking ****enable IP device tracking globally
Switch(config)# ip device tracking max <n> ***set an IP device tracking maximum on int
Switch(config-if)# ip verify source tracking [port-security] ****activate IPSG on port
Caution
Note
If you configure the ip verify source tracking [port-security] interface configuration command on a
port without enabling IP device tracking globally or setting an IP device tracking maximum on that
interface, IPSG with static hosts reject all the IP traffic from that interface.
The preceding condition also applies to IPSG with static hosts on a PVLAN host port.
•
uRPF supports up to four paths. If a packet arrives at one of the valid VLANs that is not programmed
as one of the RPF VLAN in hardware, it is dropped. If traffic may arrive from any other interfaces
without RPF configured, it can be switched.
•
Input and output ACLs cannot override or filter traffic received on an uRPF interface.
•
No CLI command exists to reflect uRPF drop packets during hardware switching. The sh ip traffic
and show cef int commands do not reflect uRPF drops.
•
IPv6 ACL is not supported on a switchport. IPv6 packets cannot be filtered on switchports using any
of the known methods: PACL, VACL, or MACLs.
37
•
Class-map match statements using match ip prec | dscp match only IPv4 packets, whereas matches
performed with match prec | dscp match both IPv4 and IPv6 packets.
•
IPv6 QoS hardware switching is disabled if the policy-map contains IPv6 ACL and match CoS in
the same class-map with the IPv6 access-list has any mask within the range /81 and /127. This
situation causes forwarding packets to software, which efficiently disables the QoS.
•
When the following data-only Catalyst 4500 linecards are used in a Catalyst 4507R-E or 4510R-E
chassis with Supervisor Engine 6-Es, the capacity of the power supply may be exceeded:
– WS-X4148-FX-MT Cisco Catalyst 4500 Fast Ethernet Switching Module, 48-port
100BASE-FX (MT-RJ)
– WS-X4448-GB-RJ45 Cisco Catalyst 4500 48-port 10/100/1000 Module (RJ-45)
The Catalyst 4503-E and Catalyst 4506-E have no caveats. The Catalyst 4507R-E configurations
that use power supplies rated at 1400 W or above also have no caveats.
The following replacement switching modules will not exceed the power supply capacity for any
Catalyst 4500-E chassis:
Recommended Replacement
Description
WS-X4148-FX-MT
WS-X4248-FE-SFP
Fast Ethernet, 48-port 100BASE-X
(SFP)
WS-X4448-GB-RJ45
WS-X4548-GB-RJ45
Enhanced 48-port 10/100/1000 Module
(RJ-45)
WS-X4448-GB-RJ45
WS-X4648-RJ45V-E
E-Series 48-port 802.3af PoE
10/100/1000 (RJ-45)
Refer to the Catalyst 4500 Series Module Installation Guide to determine the power requirements
for all of the Catalyst 4500 linecards and the power capacities of the Catalyst 4500 power supplies.
•
Supervisor Engine 6-E only supports Catalyst 4500 Series linecards in slots 8-10.
•
If you remove a line card from a redundant switch and initiate an SSO switch-over, then reinsert the
line card, all interfaces are shutdown. The remaining configuration on the original line card is
preserved.
This situation only occurs if a switch reached SSO before you removed the line card.
•
On Supervisor Engine 6-E, upstream ports support flow control auto negotiation in 1G mode only,
and flow control is forced in 10G mode. If the interface is configured to auto-negotiate the flow
control, and the interface is operating in 10G mode, the system forces flow control to ON and does
not auto-negotiate.
•
Supervisor Engine 6-E supports fast UDLD on a maximum of 32 ports.
•
With Cisco IOS Release 12.2(53)SG3 (and 12.2(54)SG), we changed the default behavior such that
your single supervisor, RPR, or fixed configuration switch does not reload automatically. To
configure automatic reload, you must enter the diagnostic fpga soft-error recover aggressive
command. (CSCth16953)
•
Energywise WOL is not “waking up” a PC in hibernate or standby mode.
Workaround: None. CSCtr51014
•
The ROMMON version number column in the output of show module command is truncated.
Workaround: Use the show version command. CSCtr30294
38
•
IP SLA session creation fails randomly for various 4-tuples.
Workaround: Select an alternate destination or source port. CSCty05405
•
The system cannot scale to greater than 512 SIP flows with MSP and metadata enabled.
Workaround: None. CSCty79236
•
On the following linecards running IOS Release 15.0(2)SG3:
– 48 10/100/1000BaseT Premium POE E Series WS-X4648-RJ45V+E (JAE14310RHU)
– 6 Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E (JAE13104VVY)
the following restrictions apply:
– Sub-interfaces are not supported on 1 Gigabit and Ten-Gigabit interfaces.
– Port-channel members do not support multiple classification criteria for a QoS policy.
– CEF is disabled automatically when uRFP is enabled and TCAM is fully utilized.
•
When you enter the ip http secure-server command (or if the system reads it from the startup
configuration), the device searches for a persistent self-signed certificate during boot up.
– If such a certificate does not exist and the device's hostname and default_domain are set, then a
persistent self-signed certificate is generated.
– If such a certificate exists, the FQDN in the certificate is compared with the current device's
hostname and default_domain. If either differs from the FQDN in the certificate, the existing
persistent self-signed certificate is replaced with a new one with the updated FQDN. Be aware
that the existing key pair is used in the new certificate.
On a switch that supports redundancy, the generation of the self-signed certificate occurs
independently on the active and the standby supervisor engines, and the certificates differ. After
switchover, the HTTP client that holds the old certificate cannot connect to the HTTPS server.
Workaround: Reconnect. CSCsb11964
•
When policing IEEE 802.1Q tagged non-IP traffic and calculating traffic conformance, the policer
excludes the four bytes that constitute the 802.1Q tag even when you enter the
qos account layer2 encapsulation command.
Workaround: None. CSCsg58526
•
When hard-coded duplex and speed settings are deleted after an interface shuts down, an a- is added
to the duplex and speed in the output from the show interface status command.
This does not affect performance.
Workaround: Enter the no shutdown command. CSCsg27395
•
When a transceiver is removed rapidly from one port and placed in another on the same chassis,
occasionally a duplicate seeprom message appears and the port is not able to handle traffic.
Workaround: Remove the transceiver from the new port and place it in the old port. After the SFP
is recognized in the old port, remove it slowly and insert it in the new port. (CSCse34693)
•
When performing an ISSU upgrade and the versions of the active and standby supervisor engines
differ, you see the following message in the standby supervisor engine console:
%XDR-6-XDRINVALIDHDR: XDR for client (CEF push) dropped (slots:2 from slot:3
context:145 length:11) due to: invalid context
Workaround: None. This is an informational message. CSCsi60898
•
An IP unnumbered configuration is lost after a switch reloads.
Workarounds: Do one of the following:
39
– After a reload, copy the startup-config to the running-config.
– Use a loopback interface as the target of the ip unnumbered command.
– Change the CLI configuration so that during bootup the router port is created first.
CSCsq63051
•
In SSO mode, when a port channel is created, deleted, and recreated on an active supervisor engine
with the same channel number, the standby port channel state goes out of sync. After a switch over,
the following message displays:
%PM-4-PORT_INCONSISTENT: STANDBY:Port is inconsistent:
Workaround: When the port channel starts to flap, enter shut and no shut on the port channel. After
the first switchover and after deleting the port channel, create a new channel. CSCsr00333
•
When you remove a line card containing ports configured with IGMP snooping while booting a
standby supervisor engine, the active supervisor engine does not synchronize this configuration to
the standby supervisor engine as a part of a bulk synchronization. When you reinstall the line card,
the configuration in the active and standby supervisor engines will differ.
Workaround: Do one of the following:
– Reload the standby switch again with the line card in place.
– Remove and reenter the commands on the active supervisor engine. The standby supervisor
engine will acquire this change. CSCsv44866
•
After posture validation succeeds, the following benign traceback messages may appear after you
unconfigure the global RADIUS and IP device tracking commands:
%SM-4-BADEVENT: Event 'eouAAAAuthor' is invalid for the current state 'eou_abort':
eou_auth 4.1.0.101
Traceback= 101D9A88 10B76BB0 10B76FE0 10B7A114 10B7A340 1066A678
106617F8
%SM-4-BADEVENT: Event 'eouAAAAuthor' is invalid for the current state 'eou_abort':
eou_auth 4.1.0.102
Traceback= 101D9A88 10B76BB0 10B76FE0 10B7A114 10B7A340 1066A678
106617F8
This applies to classic or E-series Catalyst 4500 supervisor engines running
Cisco IOS Release 12.2(50)SG
Workaround: None. CSCsw14005
•
The host's MAC address is not synchronized to the standby supervisor engine after you unconfigure
802.1X on the port and reconnect the host to a IP phone (with CDP port status TLV support) that is
connected to the switch.
If the switch were to run a supervisor switchover while in this state, the host's MAC address would
not be present in the new active supervisor engine’s MAC address table, causing possible
connectivity interruption on the host.
Workaround: Enter the shutdown command, followed by the no shutdown command on the
interface. This triggers relearning and synchronizing of the host's MAC to the standby supervisor
engine. CSCsw91661
•
On a wireless control system (WCS), some device information is incorrectly displayed for PCs
sitting behind an lldp-med capable phone. Specifically, WCS displays the phone's serial number,
model number, and software version in the PC's device information. All other information about the
PC is correctly displayed on WCS.
This only happens when the switch is running network mobility service protocol (nmsp). It does not
happen if the phone is CDP enabled.
40
Workaround: Use the VLAN ID or name to differentiate the IP phone and the PC sitting behind the
phone on the WCS.
The IP phone is detected on the voice VLAN, and the displayed information of serial number, model
number, and software version is correct. However, a PC sitting behind the phone is detected on a
data VLAN, and the displayed device information is wrong and should be ignored.
CSCsz34522
•
If time is not specified in the link debounce command, the default value depends on the supervisor
engine. The default is 10 mS for a Catalyst 4900M switch, Supervisor Engine 6-E, and Supervisor
Engine 6L-E. The default is 100 mS for all other supervisor engines.
Despite the different default value, you can configure any value in the time range.
Workaround: None. CSCte51948
•
On a peer interface on a Catalyst 4948E Ethernet Switch, if errdisabled mode flap detection is set to
a very small number (such as 2 flaps in 10 sec), a 10GE link flap may cause the peer interface to
enter the errdisabled state.
Workarounds: The Cisco switch default link-flap detection value is 5 flaps in 10 seconds. Use the
default value or larger numbers. CSCtg07677
•
After you have enabled EPM logging and the client is authenticated via MAB or Webauth, the value
of AUTHTYPE is DOT1X in EPM syslog messages irrespective of the authentication method.
Similarly, the show epm sessions command always displays the authentication method as DOT1X.
Workaround: To view the authentication method used for a client, enter the
show authentication sessions command. CSCsx42157
•
With CFM enabled globally as well as on an ingress interface, CFM packets received on the interface
are not policed with hardware control plane policing.
Workaround: None. CSCso93282
•
When either the RADIUS-server test feature is enabled or RADIUS-server dead-criteria is
configured, and either RADIUS-server deadtime is set to 0 or not configured, the RADIUS-server
status is not properly relayed to AAA.
Workaround: Configure both dead-criteria and deadtime.
radius-server dead-criteria
radius-server deadtime
CSCtl06706
•
Occasionally, if you use an X2 SR transceiver on a WS-X4706-10GE running
Cisco IOS Release 12.2(40)SG, you observe CRC errors after a reload or power cycle upon inserting
the card or X2.
Workaround: Reinsert the X2. CSCsk43618
•
Uplinks go down when you upgrade the ROMMON of an WS-X45-SUP6-E supervisor from version
12.2(40r)SG1 to a later version.
This behavior occurs in a redundant switch when the active supervisor engine is running Cisco IOS,
the standby supervisor engine is in ROMMON, and the standby supervisor engine’s ROMMON is
upgraded from version 0.34 or to a later version. The upgrade process causes the uplinks on the
standby supervisor engine to go down but the active supervisor engine is unaware of this.
Workarounds: To resume normal operation, do one of the following:
– Reload both supervisor engines with the redundancy reload shelf command.
41
– Power-cycle the standby supervisor engine by briefly pulling it from the chassis.
There is no workaround for the link flap issue. CSCsm81875
•
Changing the flow control configuration with traffic and pause frames causes some traffic loss.
This problem can happen when pause frames are sent to a switch port and the flow control receive
configuration is toggled on a 10-Gigabit Ethernet port.
Workaround: Change the flow control receive configuration when no traffic exists. CSCso71647
•
When you configure vlan dot1q tag native globally on Supervisor Engine 6-E, MST control packets
are tagged on egress on the native VLAN. This conflicts with 802.1s. The Cisco 7600 Series router
drops its MST proposal agreements (because it expects the native VLAN MST control packets to be
untagged), causing 30 seconds of traffic loss while spanning tree converges.
Workaround: Disable native VLAN tagging on the trunk port of the switch by entering the
no switchport trunk native vlan tag command. CSCsz12611
•
If a large number of VLAN mappings are configured, a member port might fail to join a port channel
and no warning is issued.
Workaround: Reduce the number of VLAN mappings. CSCtn56208
•
If an interface whose IP address is being used as the router ID is deleted or shuts down, and you
configure a service group with a multicast group address, packet redirection to CE stops and packets
are forwarded directly to the destination.
Workaround: Unconfigure and reconfigure the service group. CSCtn88087
•
Global WCCP service configuration fails to enable (WCCP global configuration is accepted but
nvgen fails) on a newly deployed switch if the switch is not enabled for SVI or a Layer 3 interface.
Workaround: Enable a Layer 3 interface in the running configuration. CSCsc88636.
•
If you use the quick option in the issu changeversion command, the following might occur:
– Links flap for various Layer 3 protocols.
– A traffic loss of several seconds is observed during the upgrade process.
Workaround: Do not use the quick option with the issu changeversion command. CSCto51562
•
When you enter the ip pim register-rate-limit command, the following error message displays:
'Failed to configure service policy on register tunnel' and 'STANDBY:Failed to
configure service policy on register tunnel'.
Workaround: None. The ip pim register-rate-limit command does not function. CSCub32679
•
For packets with the same ingress and egress Layer 3 interface, ingress QoS marking policy does
not work.
Workaround: Turn off ICMP redirect through the ip redirect command. CSCua71929
•
While configuring an IPv6 access-list, if you specify hardware statistics as the first statement in
v6 access-list mode (i.e. before issuing any other v6 ACE statement), it will not take effect.
Similarly, your hardware statistics configuration will be missing from the output of the show
running command.
You will not experience this behavior with IPv4 access lists.
Workaround: During IPv6 access-list configuration, configure at least one IPv6 ACE before the
"hardware statistics" statement. CSCuc53234
•
When an IPv6 FHS policy is applied on a VLAN and an EtherChannel port is part of that VLAN,
packets received by EtherChannel (from neighbors) are not bridged across the local switch.
42
Caveats
Workaround: Apply FHS policies on a non EtherChannel port rather than a VLAN. CSCua53148
•
Memory allocation failures can occur if more than 16K IPv6 multicast snooping entries are present.
Workaround: None. CSCuc77376
•
For any configuration where the source-interface keyword is used, if you provide an SVI that is
associated with a secondary private VLAN, configuration involving the secondary VLAN may be
lost when the switch is reloaded. In such scenarios, always use the primary private VLAN.
•
The show interface capabilities command output does not show the correct linecard model.
Workaround: Observe the show module command output. CSCua79513
•
When performing an ISSU between any releases prior to Cisco IOS 15.1(1)SG or 3.3.0SG to release
Cisco IOS 15.1(1)SG (or 3.3.0SG) or higher, a switch performing multicast routing may persistently
drop traffic after the upgrade completes. You can recover multicast traffic by reloading the chassis.
Alternately, you can remove all multicast configuration prior to ISSU, and add it back when ISSU
completes. CSCuj42672
•
When a logging discriminator is configured and applied to a device, memory leak is seen under
heavy syslog or debug output. The rate of the leak is dependent on the quantity of logs produced. In
extreme cases, the device may crash. As a workaround, disable the logging discriminator on the
device (CSCur45606, CSCur28336).
Caveats
Caveats describe unexpected behavior in Cisco IOS releases. Caveats listed as open in a prior release are
carried forward to the next release as either open or resolved.
Note
All caveats in Release 12.4 also apply to the corresponding 12.1 E releases. Refer to the Caveats for
Cisco IOS Release 12.4 publication at the following URL:
http://www.cisco.com/en/US/docs/ios/12_4/release/notes/124MCAVS.html
Note
For the latest information on PSIRTS, refer to the Security Advisories on CCO at the following URL:
http://tools.cisco.com/security/center/publicationListing
Cisco Bug Search Tool
The Bug Search Tool (BST), which is the online successor to Bug Toolkit, is designed to improve the
effectiveness in network risk management and device troubleshooting. The BST allows partners and
customers to search for software bugs based on product, release, and keyword, and aggregates key data
such as bug details, product, and version. The tool has a provision to filter bugs based on credentials to
provide external and internal bug views for the search input.
To view the details of a caveat listed in this document:
1.
Access the BST (use your Cisco user ID and password) at https://tools.cisco.com/bugsearch/.
2.
Enter the bug ID in the Search For: field.
Open Caveats for Cisco IOS Release 15.2(2)Ex, page 44
43
Caveats
Resolved Caveats for Cisco IOS Release 15.2(2)E5a, page 44
Resolved Caveats for Cisco IOS Release 15.2(2)E5, page 44
Resolved Caveats for Cisco IOS Release 15.2(2)E, page 48
Open Caveats for Cisco IOS Release 15.2(2)Ex
Use the BST to view the details of a caveat listed in this section.
Bug ID
Headline
CSCuv15017
VSS Active Reload causes CTS Ether-channel links on standby to flap
CSCuz68659
unexpected packets seen while learning the mcast traffic
Resolved Caveats for Cisco IOS Release 15.2(2)E5a
Bug ID
Headline
CSCvb19326
NTP leap second addition is not working during leap second event
CSCuv87976
CLI Knob for handling leap second add/delete ignore/ handle
CSCvb29204
BenignCertain on IOS and IOS-XE
Resolved Caveats for Cisco IOS Release 15.2(2)E5
Identifier
Description
CSCut93424
CAT4500 - Flexible Netflow start/end time inaccuracy
CSCur57853
4500 VSS cannot send snmp trap when active is down
CSCuy23874
4500: Auto-negotiation issue: port going to 100Mbps instead of 1Gbps
CSCuy52010
7940G phones learn mac in data vlan when EEE is disabled
CSCuw17135
Cat4k SUP7L-E CPU temperature sensor failed
CSCuy01942
wBulk dACL causes intermittent MAB Authentication with 4506 SUP_6
CSCuy19990
IOS 15.2 802.1x critical vlan feature - reinitialize is not working
CSCuw09327
Crash while config ACL- invalid mem access K5CpuEventCodeInputAclCopy
CSCuz02962
Increasing acl-ack-contexts for auth sessions causing memory exhaustion
44
Caveats
Bug ID
Headline
CSCuv39850
Switch crashes @auth_mgr_show_method_status_list
CSCuv87875
Crash seen@Galios_newIosHeapMemoryRef on assigning DACL on reauth
CSCuw58095
AMUR MR3: SUP8E crash at dot1x_switch_handle_vlan_removal
CSCut57300
With sec ip in SVI, routed packet is not flooded back on incoming port
CSCut71405
IGMP packet not matched by ingress QoS policy if IGMP Snooping enabled
CSCuu85298
FIB/LFIB inconcistency after BGP flap
CSCuv07111
IOS and IOS-XE devices changing the next-hop on BGP route with own IP
CSCuv07620
4500X VSS won't notify about license mismatch
CSCuu21448
ISIS Metric with Multiple instances using ciiCircLevelMetric OID
CSCuu42267
vstack status shows duplicate entries for a single PID
CSCuv23475
CPUHOG and crash on "no network 0.0.0.0" with vnet configuration on intf
CSCuu68776
Multicast boundary filter-autorp broken / WS-C4500X / 15.2(1)E 15.2(3)E1
CSCuv00910
bgp afi1/safi1 and afi1/saf4 only peers in the same update-group
CSCuv07796
Truncated output of 'show platform cpu packet buffered'
CSCuv16769
ISIS: Old path not deleted in Global RIB when new path is filtered out
CSCuv19773
"nmsp attach suppress" not being added into run-config on WS-C3850-24P
CSCuv31135
Disable connected-check in one side only makes route as unreachable
CSCuv32845
no message display even unable to allocate memory for vlan mapping
CSCuw06073
EOL CRLF in startup-config breaks 4500x VSS
CSCuv46710
Segmentation Fault in Auth Manager
CSCuv50834
High CPU due to hung NMSP Session
CSCuw21115
4500/WS-X4724-SFP-E port flaps when GLC-GE-100FX is inserted
CSCuw36865
L2 switched traffic matched by L3 SVI VACL in the output direction
CSCuw39020
access-session vlan-assignment ignore-errors breaks dynamic vlan assign
CSCuv76906
"bfd" disappears after issuing "snmp-server host x.x.x.x ABC bfd"
CSCuw09006
Voice Vlan bocked with NEAT Configuration
CSCuw48407
47xx line card failing complete diagnostics after temp sensor failure
CSCuw73525
3650 DHCPv6 Guard does not block rogue DHCP server to provide IPv6 addr
CSCtz92812
"ip vrf Liin-vrf" in running-config on a VSS system
CSCub56668
Handle C4K_HWFLOWMAN-3-NFEINTERRUPTSTATUS: module: fi
InterruptStatus:
CSCuj81067
memory leak in crypto_create_pkcs7_msg
CSCum41167
Importing multipath routes changes next-hop to 0.0.0.0 and traffic fails
CSCuw06202
Vstack Download-Config causes 4500 to become unresponsive
CSCuq36627
WAAS Express:Failed to create SSL session. (no available resources)
45
Caveats
CSCuo93205
Enable SSL Server Identity Check during SSL handshake
CSCur28336
Memory leak and possible crash when using a logging discriminator
CSCtg15739
Failed sessions are not removed in multi-auth mode
CSCur45606
logging discriminator doesn't work
CSCtb44674
High CPU due to SA-MISS event caused by own mac address packets received
CSCuq46932
Crash on dhcpd_find_binding_by_hw
CSCuu55421
Error - The FRULink 10G Service Module (C3KX-SM-10G) is not responding
CSCuv19258
DACL may not work under IBNS 2.0
CSCuv47729
Packet gets flooded back to the ingress port, when a MEC port is down
CSCuv50669
Port-security blocks X/Y/38 port due to incorrect MAC address
CSCuw52729
Enabling auto qos causes "line vty 0 4" length set to 0
CSCux18867
4500 3.6.0 False port-security alarms on standby supervisor
CSCux38988
redundancy config-sync failures mcl define interface range adds fifth ,
Bug ID
Headline
CSCum56902
Device crashes when classes removed from a policy-map
CSCum65703
Inconsistency on config "privilege" commands as seen in running-config
CSCup66629
Traceback @psecure_platform_delete_all_addrs on executing neg events
CSCup81878
Line by Line Sync fails while deleting dynamic NTP peer
CSCuq31722
The show platform software flood profile command caused SUP8 to crash
CSCuq54573
Service Policy disappears from Running Configuration of the interface
CSCur58372
“snmp-server enable traps syslog” shows in "show run all" output after removal
CSCur59242
Device crashes due to tplus_client_stop_timer
CSCus13476
CSR handled only one MACSec interface's authentication
CSCus13924
Device crashes while configuring 'Identity' commands
CSCus23125
MAC not learnt after removal of auth config
CSCus32213
CTS manual link does not come up
CSCus47009
Switch does not increment the "Received on untrusted ports" DHCP counter
CSCus79132
Dot1x authentication legacy behavior broken
CSCut05808
UDP(1975) causes Error msg %IPC-2-INVALIDZONE
CSCut10251
Some commands are not in running-config after AUTOINSTALL finishes
CSCut11679
FFM memory leak is observed when WCCP flaps
CSCut13064
BPDU filter does not work on output port when STP is disabled
CSCut13753
ACLs not syncing to the member switches on stack reload or member reload
CSCut20271
Device responds to ARP request from management port
CSCut27272
CPUHOG and crash due to Auth Manager process
46
Caveats
Bug ID
Headline
CSCut45453
ICMPv6 replies are blocked
CSCut64189
Device TELNET can enter Privileged Mode without Enable Password
CSCuu92757
4500 Sup8 MAB not triggered with"authentication control-direction in"
CSCut79680
The ip default-gateway command is not seen in running-config after AUTOINSTALL
CSCut87425
CPU hog in "EEM TCL Proc" after TCL script termination with long runtime
CSCuu22144
Vlan1 IP apply method inconsistencies across Static / DHCP / TFTP
CSCuu48400
HW CoPP counters are not incrementing
CSCuu50392
Auth Manager memory leak with ISE authentication
CSCuu90639
IP address is missing by end of Autoinstall
CSCuu92251
Removing auth mgr configs stops MAC learning on port (no MACs on MATM)
CSCuu92757
4500 Sup8 MAB not triggered with"authentication control-direction in"
CSCuv06451
IOSd crash in eap_auth_terminal_state calling free_internal
Bug ID
Headline
CSCus75890
Switch does not resync to NTP server after clock set command or reload
CSCur20444
I/O memory leak due to DHCPv6 packets
CSCur48634
HA fails due to bulk synch failure with encrypted password
CSCus57511
Switch detects high temp, and SNMP trap causes shutdown
CSCug90126
Switch returns incorrect ciscoEnvMonSupplyState SNMP values for 6000/4200 W
PSUU.
CSCul29298
Delayed detection of LinkDown message on peer interfaces
CSCuq80812
Incomplete ARP reply received on an active Flex Link port
CSCsv36934
BRIDGE-MIB query does not return information for inactive ports
CSCus32292
4506-E | SUP7L-E | 03.06.00.E | Crash - ffm ACL
CSCui99162
When IP device tracking is enabled, ARP probe response floods the VLAN
CSCtf75400
Wrong output for show platform software etherchannel port-channel n map
CSCup24975
Outage due to inconsistent software and hardware RX MTU threshold
CSCur58074
Some SFPs are not recognized when inserted into random ports on a switch
CSCuq04533
Cost for secondary VLANs is lost after each reload
CSCur21848
WCCP stops redirecting traffic when eighth port added to service group
CSCur84243
WS-X4640-CSFP-E ports (Tx) are disabled on start-up
47
Caveats
Bug ID
Headline
CSCuc03836
Switch reports SYS-2-MALLOCFAIL error for a very large amount of memory
CSCum47115
EtherType 888e unicast can not pass 2960 with new releases
CSCum80951
TCAM is not sharing when same policy is applied to multiple interfaces
CSCun80959
Desg port on the RootBridge experienced block forward for 30 sec
CSCuo51767
REP preemption is not triggered with link state change
CSCuo80260
Call-home message fails; returns "Unknown" serial number
CSCuo89407
Problem with adding new ports to a channel group.
CSCup48832
Identical IPv6 DHCP remote ID for L2 ports running source-guard/snooping
CSCup96299
IPv6 Multicast RIB entry refer to wrong distance
CSCuq02796
4500X VSS failure after adding members to port-channel
CSCuq03562
PBR: Not working in XE 3.5.0E under IPBASE license
CSCuq10827
C3560X cHsrpGrpStandbyState is incorrect
CSCuq32728
3.6.0 - IP phones reboots continuously
CSCuq39071
Mcast packet loss when other receiver leaves group in IGMPv3
CSCuq44784
Mingla2: Storm-control on EC suspended post reload
CSCur00722
Hard Reset of the Active Sup cause switch to power cycle
Resolved Caveats for Cisco IOS Release 15.2(2)E
Bug ID
Headline
CSCta61825
Blocking of unknown multicast flooding breaks ARP resolution
CSCua89658
ctrlplane policing is not working when MLD snooping is enabled
CSCub85948
Memory leak caused by CDP, LLDP or DHCP traffic
CSCuc65538
mcast dest mac incorrect on egress for packets ingressing a GR
CSCty67871
Baseboard links remain up on improper uplink module removal
CSCub44553
CPU spike seen while sending the multicast traffic to 10k Groups.
CSCub63571
AdjSameIfFail packets in a user defined vnet are dropped
CSCuc49150
User can attach input QoS policy to VSL ports, but cannot dettach it
CSCuf08112
Cat4k Active Sup crash with multi telnet session cli show power module
CSCul95289
Console / VTY / SSH session hangs on show command
48
Related Documentation
Related Documentation
Although their Release Notes are unique, the 4 platforms (Catalyst 4500, Catalyst 4900, Catalyst ME
4900, and Catalyst 4900M) use the same Software Configuration Guide, Command Reference Guide, and
System Message Guide. Refer to the following home pages for additional information:
•
Catalyst 4500 Series Switch Documentation Home
http://www.cisco.com//en/US/products/hw/switches/ps4324/index.html
Hardware Documents
Installation guides and notes including specifications and relevant safety information are available at the
following URLs:
•
Catalyst 4500 Series Switches Installation Guide
http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/hardware/installation/guide/78-14409
-08/4500inst.html
•
For information about individual switching modules and supervisors, refer to the Catalyst 4500
Series Module Installation Guide at:
http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/hardware/configuration/notes/OL_25
315.html
•
Regulatory Compliance and Safety Information for the Catalyst 4500 Series Switches
http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/hardware/regulatory/compliance/78_
13233.html
•
Installation notes for specific supervisor engines or for accessory hardware are available at:
http://www.cisco.com/en/US/products/hw/switches/ps4324/prod_installation_guides_list.html
•
Catalyst 4900 and 4900M hardware installation information is available at:
http://www.cisco.com/en/US/products/ps6021/prod_installation_guides_list.html
Software Documentation
Software release notes, configuration guides, command references, and system message guides are
available at the following URLs:
•
Catalyst 4500 release notes are available at:
http://www.cisco.com/en/US/products/hw/switches/ps4324/prod_release_notes_list.html
Software documents for the Catalyst 4500 Classic, Catalyst 4500 E-Series, Catalyst 4900 Series, and
Catalyst 4500-X Series switches are available at the following URLs:
•
Catalyst 4500 Series Software Configuration Guide
http://www.cisco.com/en/US/products/hw/switches/ps4324/products_installation_and_configurati
on_guides_list.html
•
Catalyst 4500 Series Software Command Reference
http://www.cisco.com/en/US/products/hw/switches/ps4324/prod_command_reference_list.html
•
Catalyst 4500 Series Software System Message Guide
49
Notices
http://www.cisco.com/en/US/products/hw/switches/ps4324/products_system_message_guides_list
.html
Cisco IOS Documentation
Platform-independent Cisco IOS documentation may also apply to the Catalyst 4500 and 4900 switches.
These documents are available at the following URLs:
•
Cisco IOS configuration guides, Release 12.x
http://www.cisco.com/en/US/products/ps6350/products_installation_and_configuration_guides_list.html
•
Cisco IOS command references, Release 12.x
http://www.cisco.com/en/US/products/ps6350/prod_command_reference_list.html
You can also use the Command Lookup Tool at:
http://tools.cisco.com/Support/CLILookup/cltSearchAction.do
•
Cisco IOS system messages, version 12.x
http://www.cisco.com/en/US/products/ps6350/products_system_message_guides_list.html
You can also use the Error Message Decoder tool at:
http://www.cisco.com/pcgi-bin/Support/Errordecoder/index.cgi
Notices
The following notices pertain to this software license.
OpenSSL/Open SSL Project
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit
(http://www.openssl.org/).
This product includes cryptographic software written by Eric Young ([email protected]).
This product includes software written by Tim Hudson ([email protected]).
License Issues
The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the
original SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses
are BSD-style Open Source licenses. In case of any license issues related to OpenSSL please contact
[email protected].
OpenSSL License:
Copyright © 1998-2007 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
1.
Redistributions of source code must retain the copyright notice, this list of conditions and the
following disclaimer.
50
Notices
2.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions, and
the following disclaimer in the documentation or other materials provided with the distribution.
3.
All advertising materials mentioning features or use of this software must display the following
acknowledgment: “This product includes software developed by the OpenSSL Project for use in the
OpenSSL Toolkit (http://www.openssl.org/)”.
4.
The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote
products derived from this software without prior written permission. For written permission, please
contact [email protected].
5.
Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear in
their names without prior written permission of the OpenSSL Project.
6.
Redistributions of any form whatsoever must retain the following acknowledgment:
“This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit
(http://www.openssl.org/)”.
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS”' AND ANY EXPRESSED OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
This product includes cryptographic software written by Eric Young ([email protected]). This product
includes software written by Tim Hudson ([email protected]).
Original SSLeay License:
Copyright © 1995-1998 Eric Young ([email protected]). All rights reserved.
This package is an SSL implementation written by Eric Young ([email protected]).
The implementation was written so as to conform with Netscapes SSL.
This library is free for commercial and non-commercial use as long as the following conditions are
adhered to. The following conditions apply to all code found in this distribution, be it the RC4, RSA,
lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is
covered by the same copyright terms except that the holder is Tim Hudson ([email protected]).
Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed.
If this package is used in a product, Eric Young should be given attribution as the author of the parts of
the library used. This can be in the form of a textual message at program startup or in documentation
(online or textual) provided with the package.
Redistribution and use in source and binary forms, with or without modification, are permitted provided
that the following conditions are met:
1.
Redistributions of source code must retain the copyright notice, this list of conditions and the
following disclaimer.
2.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and
the following disclaimer in the documentation or other materials provided with the distribution.
51
Notices
3.
All advertising materials mentioning features or use of this software must display the following
acknowledgement:
“This product includes cryptographic software written by Eric Young ([email protected])”.
The word ‘cryptographic’ can be left out if the routines from the library being used are not
cryptography-related.
4.
If you include any Windows specific code (or a derivative thereof) from the apps directory
(application code) you must include an acknowledgement: “This product includes software written
by Tim Hudson ([email protected])”.
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The license and distribution terms for any publicly available version or derivative of this code cannot be
changed. i.e. this code cannot simply be copied and put under another distribution license [including the
GNU Public License].
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional
information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and
revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed
and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
service and Cisco currently supports RSS Version 2.0.
This document is to be used in conjunction with the documents listed in the “Related Documentation” section.
CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and
Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco,
the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity,
Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient,
IOS, iPhone, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study, LightStream, Linksys, MeetingPlace, MGX, Networkers,
Networking Academy, Network Registrar, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way to Increase Your Internet
Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. (0711R)
Release Notes for the Catalyst 4500 Series Switch, Cisco IOS Release 15.2(1)Ex
Copyright © 1999–2016, Cisco Systems, Inc. All rights reserved.
52

Release Notes for the Catalyst 4500 Series Switch, Cisco IOS

Transcription

Documents pareils

Understanding Cisco Business Value Analysis

Jeux De Casinos Gratuit Machines A Sous 0 Slot Machines A Sous

Cisco RV132W ADSL2+ Wireless-N VPN Router Data

Cisco WBPN Wireless-N Bridge for Phone Adapters

Cisco Network Services Manager 5.0 Data sheet

Datasheet english

Cisco SPA901 1-Line IP Phone Cisco Small Business IP Phone

Cisco lance une solution de traçabilité sans fil pour les industriels

Cisco RV180 VPN Router

Cisco OneX Converter Module