ARU RFID UHF Reader System ARU-CSB-ELC-ETSI Order
Transcription
ARU RFID UHF Reader System ARU-CSB-ELC-ETSI Order
ARU RFID UHF Reader System ARU-CSB-ELC-ETSI Order-No. 52010263 The Kathrein-RFID Reader ARU-CSB-ELC-ETSI offers an Ethernet communication interface and an integrated 30° Wide Range antenna with three selectable read zones. Active and passive RFID tags can be read out in the frequency range from 865 to 868 MHz (865 to 867 MHz for India). The device can read and write tags conforming to the EPC Gen2 standard (ISO 18000-6C). The three well defined read zones of the integrated 30° Wide Range antenna will be controlled by the reader, to offer optimized solution for logistics, intralogistics and retail application. An EAS anti-theft protection system is also possible with this unit. Due to an embedded Linux-based module, the reader can be used as a stand-alone system, running applications and parameterization directly on the reader without the need for a remote PC. Order-No. Frequency range Emitted output power (max.) Protocols RX input sensitivity Internal antenna Far field half-power beam width MHz dBm dBm ° Switchable read field Polarization Antenna gain Axial ratio Communication interface Operating system reader Embedded PC module Processor Flash memory RAM Linux kernel Digital interfaces (GPIO) Current load digital interfaces (DO) Supply voltage Current consumption (at 24 V DC) dBiC dB mA °C °C mm kg • • • • • RoHS COMPLIANT Internet: https://www.kathrein-rfid.de KATHREIN-RFID • System compliant to EPC Class 1 Gen2/ISO 18000-6C standards Integrated Circular-Switch-Beam antenna with three read zones Dense Reader Mode (DRM) output power adjustable from 9 dBm up to 30 dBm ERP in 0.25 dB steps calibrated output power from 17 dBm up to 30 dBm ERP (50 mW - 1 W ERP) 4x Linux • ARMv7-A compatible processor 1GHz eMMC 4GB 512MB 200MHz DDR SDRAM > version 2.6 4 digital inputs; 4 digital outputs 500 each; max. 1500 +10 to +30 typ. 800 (without GPIO); max. 2500 (incl. GPIO) 1x M12, 4-pole, A-coded 1x M12, 4-pole, D-coded 2x M12, 8-pole, A-coded -20 to +55 -40 to +85 galvanized steel, fibreglass radome (UV resistance) approx. 620 x 386 x 112 9.0 IP 65 (at covering of not used connectors) EN 60529, EN301489-1, EN 302208-1, EN 302208-2, EN 60950-1:2006, EN 50364 mA V DC Technical Features: ® 30 vertical 80 horizontal +35 / 0 / -35 circular 6 typ. 2 Ethernet 10/100 MBit/s Kathrein firmware @ ARM 9 processor ° Connector (male) power supply Connector (female) Ethernet Connector (female) GPIO Operating temperature range Storage temperature range Housing materials Dimensions (without brackets) (L x W x H) Weight Degree of protection Conform to Made in Germany 52010263 865-868 (865-867 for India) +30 ERP EPC Class1 Gen2/ISO 18000-6C typ. -80 Ethernet GPIO Antenna integrated Manuals: https://www.kathrein-rfid.de/en/download-overview.html Kronstaudener Weg 1 • 83071 Stephanskirchen • Germany • Phone: +49 8036 90831-23 Page: 1 of 2 Doc.-No.: 936B105B Order-No.: 52010263 date of creation: 13.01.2015 subject to change • Fax: +49 8036 90831-99 ARU RFID UHF Reader System ARU-CSB-ELC-ETSI Order-No. 52010263 Dimensions in [mm]: Antenna features: Read range vertical cut Read range horizontal cut (if mounted like picture) Directions of the switched beam Electrical interfaces: Power supply: Ethernet: Allocation +24 V DC n.c. GND n.c. Pin 1 2 3 4 Pin 1 2 3 4 Allocation TD+ RD+ TDRD- Digital inputs and outputs (GPIO): Pin 1 2 3 4 5 6 7 8 GPIO 2 OUT_CMN INPUT 0 INP_CMN GND Vcc OUTPUT 1 OUTPUT 0 INPUT 1 GPIO 1 OUT_CMN INPUT 3 INP_CMN GND Vcc OUTPUT 3 OUTPUT 2 INPUT 2 Scope of delivery: • CD-ROM with manual and data sheet (.pdf) • Grounding set M6 Accessories (optional): • • • • RoHS Made in Germany 4x ® COMPLIANT Linux Internet: https://www.kathrein-rfid.de KATHREIN-RFID • Cable adaptor set (Order-No. 52010126; includes: 1x power supply cable, 1x Ethernet port cable, 2 x GPIO cable mast bracket (Order-No. 52010005), mounting kit for outdoor use protective cover set (Order-No. 52010127) • Ethernet GPIO Antenna integrated Manuals: https://www.kathrein-rfid.de/en/download-overview.html Kronstaudener Weg 1 • 83071 Stephanskirchen • Germany • Phone: +49 8036 90831-23 Page: 2 of 2 Doc.-No.: 936B105B Order-No.: 52010263 date of creation: 13.01.2015 subject to change • Fax: +49 8036 90831-99 ARU RFID UHF Reader-System ARU-CSB-ELC-ETSI Bestell-Nr. 52010263 Der Kathrein-RFID Reader ARU-CSB-ELC-ETSI hat eine Ethernet-Schnittstelle und eine integrierte 30° Wide Range-Antenne mit drei wählbaren Lesezonen. Aktive und passive RFIDTags können im Frequenzbereich 865 bis 868 MHz (865 bis 867 MHz für Indien) ausgelesen werden. Das Gerät kann Tags nach dem EPC Gen2 Standard (ISO 18000-6C) lesen und schreiben. Die drei definierten Lesezonen der integrierten 30° Wide Range-Antenne werden vom Reader gesteuert, um eine optimiale Lösung für Logistik, Intralogistik und RetailAnwendung zu bieten. Ein EAS Diebstahlschutzsystem ist mit dieser Einheit ebenfalls möglich. Durch das integrierte Modul auf Linux-Basis kann der Reader als Stand-aloneSystem genutzt werden, um Applikationen sowie Parametrierungen direkt auf dem Reader laufen zu lassen, ohne einen Remote-PC zu benötigen. Bestell-Nr. Frequenzbereich abgestrahlte Ausgangsleistung (max.) unterstützte Protokolle RX-Eingangsempfindlichkeit Interne Antenne Fernfeldöffnungswinkel MHz dBm dBm ° Schwenkbereich Polarisation Antennen-Gewinn Achsverhältnis Kommunikations-Schnittstelle Reader-Betriebssystem Embedded-PC-Modul Prozessor Flash-Speicher RAM Linux-Kernel Digitalschnittstellen (GPIO) Strombelastung Digitalschnittstellen (DO) Spannungsversorgung Stromaufnahme (bei 24 V DC) Ausstattung: dBiC dB mA RoHS COMPLIANT Internet: https://www.kathrein-rfid.de KATHREIN-RFID • °C °C mm kg Das System entspricht dem Standard EPC Class 1 Gen2/ISO 18000-6C integrierte Circular-Switch-Beam Antenne mit drei definierten Lesezonen beherrscht Dense Reader Mode (DRM) Ausgangsleistung einstellbar von 9 dBm bis 30 dBm ERP in 0,25 dB Schritten von 17 dBm bis 30 dBm ERP (50 mW - 1 W ERP) ist die Ausgangsleistung kalibriert 4x Linux • ARMv7-A kompatibler Prozessor 1GHz eMMC 4GB 512MB 200MHz DDR SDRAM > Version 2.6 4 digitale Eingänge; 4 digitale Ausgänge je 500; max. 1500 +10 bis +30 typ. 800 (ohne GPIO); max. 2500 (inkl. GPIO) 1x M12, 4-polig, A-kodiert 1x M12, 4-polig, D-kodiert 2x M12, 8-polig, A-kodiert -20 bis +55 -40 bis +85 Stahl verzinkt, Fiberglas Radome (UV-beständig) ca. 620 x 386 x 112 9,0 IP 65 (bei Abdeckung nicht genutzter Anschlüsse) EN 60529, EN301489-1, EN 302208-1, EN 302208-2, EN 60950-1:2006, EN 50364 mA V DC • • • • • • ® 30 vertikal 80 horizontal +35 / 0 / -35 zirkular 6 typ. 2 Ethernet 10/100 MBit/s Kathrein-Firmware @ ARM 9 Prozessor ° Anschlussstecker Stromversorgung Anschlussbuchse Ethernet Anschlussbuchse GPIO Betriebs-Temperaturbereich Lager-Temperaturbereich Gehäusematerial Abmessungen (ohne Wandhalterungen) (L x B x H) Gewicht Schutzart Konformität Made in Germany 52010263 865-868 (865-867 für Indien) +30 ERP EPC Class1 Gen2/ISO 18000-6C typ. -80 Ethernet GPIO Seite: 1 von 2 Dok.-Nr.: 936B105B Bestell-Nr.: 52010263 Erstelldatum: 13.01.2015 Änderungen vorbehalten Antenna integrated Handbücher: https://www.kathrein-rfid.de/downloaduebersicht.html Kronstaudener Weg 1 • 83071 Stephanskirchen • Germany • Phone: +49 8036 90831-23 • Fax: +49 8036 90831-99 ARU RFID UHF Reader-System ARU-CSB-ELC-ETSI Bestell-Nr. 52010263 Abmessungen in [mm]: Antennenmerkmale: Lesereichweite Vertikalschnitt Lesereichweite Horizontalschnitt (montiert wie in Bild) Richtung des Schwenkbereichs Elektrische Schnittstellen: Ethernet: Stromversorgung: Pin 1 2 3 4 Belegung +24 V DC n.c. GND n.c. Pin 1 2 3 4 Belegung TD+ RD+ TDRD- Digitale Ein- und Ausgänge (GPIO): Pin 1 2 3 4 5 6 7 8 GPIO 2 OUT_CMN INPUT 0 INP_CMN GND Ub OUTPUT 1 OUTPUT 0 INPUT 1 GPIO 1 OUT_CMN INPUT 3 INP_CMN GND Ub OUTPUT 3 OUTPUT 2 INPUT 2 Lieferumfang: • CD-ROM mit Bedienerhandbuch und Datenblatt (.pdf) • Erdungsset M6 Zubehör (optional): • • • • RoHS Made in Germany 4x ® COMPLIANT Linux Internet: http://www.kathrein-rfid.de KATHREIN-RFID • Kabel-Adaptersatz (Bestell-Nr. 52010126; bestehend aus: 1x Stromversorgungskabel, 1x Ethernet-Schnittstellenkabel, 2x GPIO-Kabel Masthalterung (Bestell-Nr. 52010005), Montagekit für Außenbereich Schutzkappenset (Bestell-Nr. 52010127) • Ethernet GPIO Seite: 2 von 2 Dok.-Nr.: 936B105B Bestell-Nr.: 52010263 Erstelldatum: 13.01.2015 Änderungen vorbehalten Antenna integrated Handbücher: https://www.kathrein-rfid.de/de/software-und-downloads Kronstaudener Weg 1 • 83071 Stephanskirchen • Germany • Phone: +49 8036 90831-23 • Fax: +49 8036 90831-99